SEAGATE ST2000DM008 2TB 3.5 Inch Internal Hard Drive User Manual

SEAGATE ST2000DM008 2TB 3.5 Inch Internal Hard Drive

© 2023, Seagate Technology LLC All rights reserved. Publication number: 100817550 Rev. N, March 2023 Seagate Technology reserves the right to make changes to the product(s) or information disclosed herein at any time without notice. Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. SeaTools is either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners. No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC. Call 877-PUB-TEK1(877-782-8351) to request permission. When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment and other factors. The export or re- export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for more information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications.

Seagate® Technology Support Services

• For Seagate Product Support, visit: www.seagate.com/support
• For Seagate Compliance, Safety, and Disposal, visit: www.seagate.com/support
• For Firmware Download and Tools Download for Secure Erase, visit: www.seagate.com/support/downloads/For information regarding online support and services, visit: www.seagate.com/contacts/
• For information regarding Warranty Support, visit: www.seagate.com/support/warranty-and-replacements/For information regarding data recovery services, visit: www.seagate.com/services-software/recover/resources/For Seagate OEM and Distribution
• partner and Seagate reseller portal, visit: www.seagate.com/partners

Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate® BarraCuda® model drives:

• ST2000DM008
• ST1000DM014

These drives provide the following key features:

• Compliant with RoHS requirements in China and Europe.
• High instantaneous (burst) data-transfer rates (up to 600MB per second).
• Native Command Queuing with command ordering to increase performance in demanding applications.
• Quiet operation.
• SeaToolsTM diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Supports latching SATA cables and connectors.
• Worldwide Name (WWN) capability uniquely identifies the drive.

About the SATA interface
The Serial ATA (SATA) interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.

In addition, SATA makes the transition from parallel ATA easy by providing legacy software support. SATA was designed to allow users to install a SATA host adapter and SATA disk drive in the current system and expect all of the existing applications to work as normal. The SATA interface connects each disk drive in a point-to-point configuration with the SATA host adapter. There is no master/slave relationship with SATA devices like there is with parallel ATA. If two drives are attached on one SATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0 (master) devices. The SATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated. The SATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All SATA devices behave like Device 0 devices. For additional information about how SATA emulates parallel ATA, refer to the “Serial ATA International Organization: Serial ATA Revision 3.0”. The specification can be downloaded from www.sata-io.org.

Note
The host adapter may, optionally, emulate a master/slave environment to host software where two devices on separate SATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical SATA environment.

Drive Specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models:

• ST2000DM008
• ST1000DM014

Specification summary tables
The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to the appropriate section of this manual.

Table 1 Drive specifications summary for 2TB and 1TB models

Bytes per sector

(4K physical emulated at 512-byte sectors)

| 4096
Default sectors per track| 63
Default read/write heads| 16
Default cylinders| 16,383
Recording density (max)| 2200 kB/in
Track density (avg)| 540 ktracks/in
Areal density (avg)| 1188 Gb/in2
Spindle speed (RPM)| 7200
SATA interface transfer rate| 600 MB/s
Maximum data transfer rate| 220 MB/s
__

ATA data-transfer modes supported

| PIO modes: 0 to 4

Multiword DMA modes: 0 to 2

Ultra DMA modes 0 to 6

Cache buffer| 256MB
Height (max)| 20.20mm / 0.795 in
Width (max)| 101.6mm (± 0.25) / 4.0 in (± 0.010)
Length (max)| 146.99mm / 5.787 in
Weight (typical)| 490g / 1.08 lb
Average latency| 4.167 ms
Power-on to ready (typ)| 11.0s
Standby to ready (typ)| 11.0s
Startup current (typical) 12V| 2.0A
Voltage tolerance (including noise)| 5V ±5%

12V ±10%

Non-Operating (Ambient °C)| –40° to 70°
Operating ambient temperature (min °C)| 0°
Operating temperature (drive case max °C)| 60°†
Temperature gradient| 20°C per hour max (operating) 30°C per hour max (non- operating)
Relative humidity| 5% to 90% (operating)

5% to 95% (non-operating)

Relative humidity gradient (max)| 30% per hour
Drive **Specification*| ST2000DM008 and ST1000DM014
---|---
Wet bulb temperature (max)| 30°C max (operating) 40°C max (non-operating)
Altitude, operating| –304m to 3048m (–1000 ft to 10,000 ft)
Altitude, non-operating (below mean sea level, max)| –304m to12,192m (–1000 ft to 40,000+ ft)
Operational shock (max)| 80 Gs (read) / 70 Gs (write) at 2ms
Non-operational shock (max)| 350 Gs at 2ms
__**

Vibration, operating

| 10Hz to 22Hz: 0.25 Gs, Limited displacement 22Hz to 350Hz: 0.50 Gs

350Hz to 500Hz: 0.25 Gs

__

Vibration, non-operating

| 5Hz to 22Hz: 3.0 Gs 22Hz to 350Hz: 3.0 Gs

350Hz to 500Hz: 3.0 Gs

Drive acoustics, sound power|
Idle***| 2.8  bels (typical)

2.9  bels (max)

Seek| 3.1 bels (typical)

3.3 bels (max)

Non-recoverable read errors| 1 per 1014 bits read
__

__

Rated workload

| Average annualized workload rating: <55 TB/year.

The specifications for the product assumes the I/O workload does not exceed the average annualized workload rate limit of 55 TB/year. Workloads exceeding the annualized rate may degrade and impact reliability as experienced by the particular application. The average annualized workload rate limit is in units of TB per calendar year.

__

Warranty

| To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/warranty-and- replacements/ From this page, click on “Is my Drive under Warranty”. Users will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for the drive.
Load/unload cycles| 600,000 at 25°C, 50% rel. humidity
Supports hotplug operation per the Serial ATA Revision 3.2 specification| Yes

• All specifications above are based on native configurations.
• One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.
• During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.
• Seagate does not recommend operating at sustained case temperatures above 60°C. Operating at higher temperatures will reduce useful life of the product.

Note
If the drive is powered off before issuing the flush cache command, in some instances, the end-user data in the DRAM cache might not be committed to the disk.

Formatted capacity

Model| Formatted **capacity*| Guaranteed sectors| Bytes per sector
---|---|---|---
2TB| 2000GB| 3,907,029,168| **

4096

1TB| 1000GB| 1,953,525,168

• One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting.

LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.3.1, “Identify Device command” (words 60-61 and 100-103) for additional information about 48-bit addressing support of drives with capacities over 137GB.

Default logical geometry

• Cylinders: 16,383
• Read/write heads: 16
• Sectors per track: 63

LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above.

Recording and interface technology

Physical characteristics

Start/stop times
The start/stop times are listed below.

Time-to-ready may be longer than normal if the drive power is removed without going through normal OS power-down procedures.

Power specifications
The drive receives DC power (+5V or +12V) through a native SATA power connector. Refer to Figure 1 on page 16.

Power consumption
Power requirements for the drives are listed in Table 2. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. These power measurements are done with DIPM enabled.

• Spinup current is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Read/Write current is measured with the heads on track, based on three 64-sector read or write operations every 100 ms.
• The drive supports three idle modes: Performance Idle mode, Active Idle mode and Low Power Idle mode. Refer to Section 2.7.4 for power-management modes.

Table 2 DC power requirements for 2TB and 1TB models

Power dissipation| Avg (watts 25° C)| Avg 12V type amps
---|---|---
Spinup| —| 2.0
Idle, Low Power| 3.9|
Read/Write| 5.1|
Standby| 0.3|
Sleep| 0.3|

Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.

• Using 12-volt power, the drive is expected to operate with a maximum of 200 mV peak-to-peak sine-wave injected noise at up to 10MHz.
• Using 5-volt power, the drive is expected to operate with a maximum of 150 mV peak-to-peak sine-wave injected noise at up to  10MHz.

Note Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.

Voltage tolerance
Voltage tolerance (including noise):

• 5V ±5%
• 12V ±10%

Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems, users can control power management through the system setup program. The drive features the following power-management modes:

Active mode
The drive is in Active mode during the read/write and seek operations.

Idle mode
The electronics remain powered, and the drive accepts all commands and returns to Active mode when disk access is necessary.

Standby mode
The drive enters Standby mode immediately when the host sends a Standby Immediate command. If the host has set the standby timer, the drive enters Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby mode, the electronics are in low power mode, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to Active mode when disk access is necessary.

Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the electronics are in low power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby mode.

Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands  and returns to Active mode when disk access is necessary.

Environmental specifications
This section provides the temperature, humidity, shock, and vibration specifications for Barracuda drives. Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000ft. (305 meters), the maximum temperature is derated linearly by 1°C every 1000 ft. Refer to Section 3.4 on page 17 for base plate measurement location.

Ambient Temperature

• Non-operating (Ambient) –40° to 70°C (–40° to 158°F)
• Operating ambient (min °C) 0° (32°F)
• Operating (Drive case max °C) 60° (140°F) †
• Seagate does not recommend operating at sustained case temperatures above 60°C. Operating at higher temperatures will reduce useful life of the product.

Temperature gradient

• Operating 20°C per hour (68°F per hour max), without condensation
• Non-operating 30°C per hour (54°F per hour max)

Humidity

Relative humidity

• Operating 5% to 90% non-condensing (30% per hour max)
• non-operating 5% to 95% non-condensing (30% per hour max)

Wet bulb temperature

• Operating 30°C / 86°F (rated)
• Non-operating 40°C / 104°F (rated)

Altitude

• Operating –304m to 3048m (–1000 ft. to 10,000 ft.)
• Non-operating –304m to 12,192m (–1000 ft. to 40,000+ ft.)

Shock and Vibration
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 80 Gs (read) / 70 Gs (write) based on half-sine shock pulses of 2ms during read operations. Shocks should not be repeated more than two times per second.

Non-operating shock
The non-operating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on a non-repetitive half-sine shock pulse of
2ms duration.

Operating vibration
The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below.

• 10Hz to 22Hz 0.25 Gs (Limited displacement)
• 22Hz to 350Hz 0.50 Gs
• 350Hz to 500Hz 0.25 Gs

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis. Throughput may vary if improperly mounted.

Non-operating vibration
The maximum non-operating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below.

• 5Hz to 22Hz 3.0 Gs (Limited displacement)
• 22Hz to 350Hz 3.0 Gs
• 350Hz to 500Hz 3.0 Gs

Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.

Note
For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.4 / (average latency + average access time

Table 3 Fluid Dynamic Bearing (FDB) motor acoustics

2.9  bels (max)

| 3.1 bels (typical)

3.3 bels (max)

Test for Prominent Discrete Tones (PDTs)
Seagate follows the ECMA-74 standards for the measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to the computation of tone ratios according to Annex D of the ECMA-74 standards.

Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in Table 4.

Table 4 Radiofrequency environments

Test| Description| Performance level| Reference standard
---|---|---|---
Electrostatic discharge| Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV| B| EN61000-4-2: 95
Radiated RF immunity| 80MHz to 1,000MHz, 3 V/m,

80% AM with 1kHz sine

| A| EN61000-4-3: 96
Electrical fast transient| ± 1 kV on AC mains, ± 0.5 kV on external I/O| B| EN61000-4-4: 95
Surge immunity| ± 1 kV differential, ± 2 kV common, AC mains| B| EN61000-4-5: 95
Conducted RF immunity| 150kHz to 80MHz, 3 Vrms, 80% AM with 1kHz sine| A| EN61000-4-6: 97
Voltage dips, interrupts| 0% open, 5 seconds

0% short, 5 seconds

40%, 0.10 seconds

70%, 0.01 seconds

| C C C B| EN61000-4-11: 94

Warranty
To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/warranty-and-replacements/ From this page, click on “Is my Drive under Warranty”. Users will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for the drive.

Storage
Maximum storage periods are 180 days within the original unopened Seagate shipping package or 60 days unpackaged within the defined non-operating limits (refer to the environmental section in this manual). Storage can be extended to 1 year packaged or unpackaged under optimal environmental conditions (25°C, <40% relative humidity non-condensing, and non-corrosive environment). During any storage period the drive non-operational temperature, humidity, wet bulb, atmospheric conditions, shock, vibration, magnetic and electrical field specifications should be followed.

Data loss under power interruption with write cache enabled
Drive preserves its data during all operations except in cases where the power to the drive is interrupted during write operations. This could result in either an uncorrected data error being reported, or the entire sector/track becoming unreadable. This can be permanently recovered by rewriting to the same location on the drive. Additionally, any data present in the DRAM buffer will not be written to the disk media, additionally, the drive will not be able to return the original data. To prevent this data loss, the host should issue a standby immediate or flush cache command before a controlled power off operation to the drive.

HDD and SSD Regulatory Compliance and Safety
For the latest regulatory and compliance information see: www.seagate.com/support/ scroll down the page and click the Compliance, Safety and Disposal Guide link.

Regulatory models
The following regulatory model number represents all features and configurations within the series: Regulatory Model Numbers: SKR005

Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years of exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution when exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Configuring and Mounting the Drive

This section contains the specifications and instructions for configuring and mounting the drive.

Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:.

Caution

• Before handling the drive, put on a grounded wrist strap, or ground oneself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.
• Handle the drive by its edges or frame only.
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until mounting it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

Configuring the drive
Each drive on the SATA interface connects point-to-point with the SATA host adapter. There is no master/slave relationship because each driver is considered a master in a point-to-point relationship. If two drives are attached on one SATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices. SATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive for proper operation; however, if users connect the drive and receive a “drive not detected” error, the SATA-equipped motherboard or host adapter may use a chipset that does not support SATA speed auto-negotiation.

SATA cables and connectors
The SATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 5 for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host. For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate features that enable the direct connection to be hot-pluggable and blind-mateable. For installations that require cables, users can connect the drive as illustrated in Figure 1.

Each cable is keyed to ensure correct orientation. Seagate BarraCuda drives support latching SATA connectors.

Drive mounting
Users can mount the drive in any orientation using four screws in the side- mounting holes or four screws in the bottom-mounting holes. Refer to Figure 2 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:

• Allow a minimum clearance of 0.030 inches (0.76mm) around the entire perimeter of the drive for cooling.
• Use only 6-32 UNC mounting screws.
• The screws should be inserted no more than 0.140 inch (3.56 mm) into the bottom or side mounting holes.
• Do not overtighten the mounting screws (maximum torque: 8 inch-lbs max).

SATA Interface

These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6. For detailed information about the SATA interface, refer to the “Serial ATA: High- Speed Serialized AT Attachment” specification.

Hot-Plug compatibility
Seagate BarraCuda drives incorporate connectors that enable users to hot plug these drives per the SATA Revision 3.2 specification. This specification can be downloaded from www.serialata.org.

SATA device plug connector pin definitions
Table 5 summarizes the signals on the SATA interface and power connectors.

Table 5 SATA connector pin definitions

Key and spacing separate signal and power segments
Power| P1| V33| 3.3V power
P2| V33| 3.3V power
P3| V33| 3.3V power, pre-charge, 2nd mate
P4| Ground| 1st mate
P5| Ground| 2nd mate
P6| Ground| 2nd mate
P7| V5| 5V power, pre-charge, 2nd mate
P8| V5| 5V power
P9| V5| 5V power
P10| Ground| 2nd mate
P11| Ground or LED signal| If grounded, drive does not use deferred spin
P12| Ground| 1st mate.
P13| V12| 12V power, pre-charge, 2nd mate
P14| V12| 12V power
P15| V12| 12V power

Notes

1. All pins are in a single row, with a 1.27 mm (0.050 in) pitch.
2. The comments on the mating sequence apply to the case of the backplane blindmate connector only. In this case, the mating sequences are:
   • the ground pins P4 and P12.
   • the pre-charge power pins and the other ground pins.
   • the signal pins and the rest of the power pins.
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration.
   • All used voltage pins (Vx) must be terminated.

Supported ATA commands
The following table lists the SATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 3.0 (www.sata- io.org). See “S.M.A.R.T. commands” on page 27 for details and subcommands used in the S.M.A.R.T. implementation.

Table 6 SATA standard commands

Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right.| Address: 00H

Password:                         01H

Lock:                               02H

Unlock:                            03H

Freeze Lock:                        04H

Set Max Address Extended| 37H
Set Multiple Mode| C6H
Sleep| E6H
S.M.A.R.T. Disable Operations| B0H / D9H
S.M.A.R.T. Enable/Disable Autosave| B0H / D2H
S.M.A.R.T. Enable Operations| B0H / D8H
S.M.A.R.T. Execute Offline| B0H / D4H
S.M.A.R.T. Read Attribute Thresholds| B0H / D1H
S.M.A.R.T. Read Data| B0H / D0H
S.M.A.R.T. Read Log Sector| B0H / D5H
S.M.A.R.T. Return Status| B0H / DAH
S.M.A.R.T. Save Attribute Values| B0H / D3H
S.M.A.R.T. Write Log Sector| B0H / D6H
Standby| E2H
Standby Immediate| E0H
Write Buffer| E8H
Write Buffer DMA| EBH
Write DMA| CAH
Write DMA Extended| 35H
Write DMA FUA Extended| 3DH
Write FPDMA Queued| 61H
Write Log Extended| 3FH
Write Log DMA Extended| 57H
Write Multiple| C5H
Write Multiple Extended| 39H
Write Multiple FUA Extended| CEH
Write Sectors| 30H
Write Sectors Extended| 34H
Write Uncorrectable| 45H

Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in “Supported ATA commands” on page 19. All
reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. The following commands contain drive-specific features that may not be included in the SATA specification.

Table 7 Identify Device commands

__

__

0

| Configuration information:

•   Bit 15: 0 = ATA; 1 = ATAPI

•  Bit 7: removable media

•  Bit 6: removable controller

•  Bit 0: reserved

| __

__

0C5AH

1| Number of logical cylinders| 16,383
__

__

__

2

| Specific configuration:

__

37C8h Device requires SET FEATURES subcommand to spin-up after power-up and IDENTIFY DEVICE data is incomplete.

738Ch Device requires SET FEATURES subcommand to spin-up after power-up and IDENTIFY DEVICE data is complete.

8C73h Device does not require SET FEATURES subcommand to spin-up after power- up and IDENTIFY DEVICE data is incomplete.

C837h Device does not require SET FEATURES subcommand to spin-up after power- up and IDENTIFY DEVICE data is complete.

| __

__

__

C837H

3| Number of logical heads| 16
4| Retired| 0000H
5| Retired| 0000H
6| Number of logical sectors per logical track: 63| 003FH
7–9| Retired| 0000H
10–19| Serial number: (20 ASCII characters, 0000H = none)| ASCII
20| Retired| 0000H
21| Retired| 0000H
22| Obsolete| 0000H
23–26| Firmware revision

(8 ASCII character string, padded with blanks to end of string)

| x.xx
27–46| Drive model number:

(40 ASCII characters, padded with blanks to end of string)

|
47| (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16)| 8010H
__

__

48

| Trusted Computing feature set options:

15 Shall be cleared to zero 14 Shall be set to one

13:1 Reserved for the Trusted Computing Group 0 Trusted Computing feature set is supported

| __

__

4000H

49| Standard Standby timer, IORDY supported and may be disabled| 2F00H
Word| Description| Value
---|---|---
__

__

50

| Capabilities: (see 7.17.7.17)

15 Shall be cleared to zero 14 Shall be set to one

13:2 Reserved

1 Obsolete

0 Shall be set to one to indicate a vendor specific Standby timer value minimum

| __

__

4000H

51| PIO data-transfer cycle timing mode| 0200H
52| Retired (Obsolete)| 0200H
__

__

53

| 15:8 Free-fall Control Sensitivity 7:3 Reserved

2 the fields reported in word 88 are valid

1 the fields reported in words (70:64) are valid 0 Obsolete

| __

0007H

54| Number of current logical cylinders (Obsolete)| xxxx H
55| Number of current logical heads (Obsolete)| xxxx H
56| Number of current logical sectors per logical track (Obsolete)| xxxx H
57–58| Current capacity in sectors (Obsolete)| xxxx H
__

__

__

59

| 15 The BLOCK ERASE EXT command is supported 14 The OVERWRITE EXT command is supported

13 The CRYPTO SCRAMBLE EXT command is supported 12 The Sanitize feature set is supported

11:9 Reserved

8 Multiple logical sector setting is valid

7:0 Current setting for number of logical sectors that shall be transferred per DRQ data block on READ/WRITE Multiple commands

| __

__

__

5D10H

__

__

60–61

| Total number of user-addressable LBA sectors available (see Section 2.2for related information)

*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB). Drives with capacities over 137GB will have 0FFFFFFFh in this field and the actual number of user-addressable LBAs specified in words 100-103. This is required for drives that support the 48-bit addressing feature.

| __

__

0FFFFFFFh*

62| Obsolete| 0000H
63| Multiword DMA active and modes supported (see note following this table)| xx 07H
64| Advanced PIO modes supported (modes 3 and 4 supported)| 0003H
65| Minimum multiword DMA transfer cycle time per word (120 nsec)| 0078H
66| Recommended multiword DMA transfer cycle time per word (120 nsec)| 0078H
67| Minimum PIO cycle time without IORDY flow control (240 nsec)| 0078H
68| Minimum PIO cycle time with IORDY flow control (120 nsec)| 0078H
Word| Description| Value
---|---|---
__

__

__

__

__

__

69

| Additional Supported

15 CFast Specification Support

14 Deterministic data in trimmed LBA range(s) is supported

13 Long Physical Sector Alignment Error Reporting Control is supported 12 Obsolete

11 READ BUFFER DMA is supported 10 WRITE BUFFER DMA is supported 9 Obsolete

8 DOWNLOAD MICROCODE DMA is supported 7 Reserved for IEEE 1667

6 0 = Optional ATA device 28-bit commands supported

5 Trimmed LBA range(s) returning zeroed data is supported 4 Device Encrypts All User Data

3 Extended Number of User Addressable Sectors is supported 2 All write cache is non-volatile

1:0 Reserved

| __

__

__

__

__

__

0000H

70–74| ATA-reserved| 0000H
75| Queue depth| 001FH
76| SATA capabilities| xxxxH
77| Reserved for future SATA definition| xxxxH
78| SATA features supported| xxxxH
79| SATA features enabled| xxxxH
80| Major version number| 07E0H
81| Minor version number| 006DH
82| Command sets supported| 346BH
83| Command sets supported| 7D69H
84| Command sets support extension (see note following this table)| 4163H
85| Command sets enabled| 34 xx H
86| Command sets enabled| BC49H
87| Command sets enable extension| 4163H
88| Ultra DMA support and current mode (see note following this table)| xx 7FH
89| Security erase time| xxxx H
90| Enhanced security erase time| xxxx H
92| Master password revision code| FFFEH
93| Hardware reset value| xxxx H
94| Automatic acoustic management| D0D0H
95–99| ATA-reserved| 0000H
__

100–103

| Total number of user-addressable LBA sectors available (see Section 2.2for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh.| ST2000DM008 = 3,907,029,168

ST1000DM014 = 1,953,525,168

104| ATA-reserved| 0000H
105| ATA-reserved| 0008H
Word| Description| Value
---|---|---
106| Physical sector size / logical sector size| 6003H
107| ATA-reserved| 0000H
108-111| The mandatory value of the worldwide name (WWN) for the drive.

NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support.

| Each drive will have a unique value.
112-118| ATA-reserved| 0000H
119| Commands and feature sets supported| 405CH
120| Commands and feature sets supported or enabled| 405CH
121-127| ATA-reserved| 0000H
128| Security status| 0021H
129–159| Seagate-reserved| xxxx H
160–167| ATA-reserved| 0000H
168| Device Nominal Form Factor| 0002H
169-205| ATA-reserved| 0000H
206| SCT Command Transport| 30A5H
207-208| ATA-reserved| 0000H
209| Alignment of logical blocks within a physical block| 4000H
210-216| ATA-reserved| 0000H
217| Nominal media rotation rate| 1C20H
218-221| ATA-reserved| 0000H
222| Transport major version number| 107FH
223-229| ATA-reserved| 0000H
230-233| Extended Number of User Addressable Sectors| ST2000DM008 = 3,907,029,168

ST1000DM014 = 1,953,525,168

234–254| ATA-reserved| 0000H
255| Integrity word| xxA5H

Note
Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported.

Note
See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data.

Description (if bit is set to 1)

 | Bit| Word 63
 | 0| Multiword DMA mode 0 is supported.
 | 1| Multiword DMA mode 1 is supported.
 | 2| Multiword DMA mode 2 is supported.
 | 8| Multiword DMA mode 0 is currently active.
 | 9| Multiword DMA mode 1 is currently active.
 | 10| Multiword DMA mode 2 is currently active.
 | Bit| Word 84
 | 0| SMART error login is supported.
 | 1| SMART self-test is supported.
 | 2| Media serial number is supported.
 | 3| Media Card Pass Through Command feature set is supported.
 | 4| Streaming feature set is supported.
 | 5| GPL feature set is supported.
 | 6| WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported.
 | 7| WRITE DMA QUEUED FUA EXT command is supported.
 | 8| 64-bit World Wide Name is supported.
 | 9-10| Obsolete.
 | 11-12| Reserved for TLC.
 | 13| IDLE IMMEDIATE command with IUNLOAD feature is supported.
 | 14| Shall be set to 1.
 | 15| Shall be cleared to 0.
 | Bit| Word 88
 | 0| Ultra DMA mode 0 is supported.
 | 1| Ultra DMA mode 1 is supported.
 | 2| Ultra DMA mode 2 is supported.
 | 3| Ultra DMA mode 3 is supported.
 | 4| Ultra DMA mode 4 is supported.
 | 5| Ultra DMA mode 5 is supported.
 | 6| Ultra DMA mode 6 is supported.
 | 8| Ultra DMA mode 0 is currently active.
 | 9| Ultra DMA mode 1 is currently active.
 | 10| Ultra DMA mode 2 is currently active.
 | 11| Ultra DMA mode 3 is currently active.
 | 12| Ultra DMA mode 4 is currently active.
 | 13| Ultra DMA mode 5 is currently active.
 | 14| Ultra DMA mode 6 is currently active.

Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows:

Table 8 Set Features command

register values:
 | 00H  Set PIO mode to default (PIO mode 2)
 | 01H  Set PIO mode to default and disable IORDY (PIO mode 2)
 | 08H PIO mode 0
 | 09H PIO mode 1
 | 0AH PIO mode 2
 | 0BH PIO mode 3
 | 0CH PIO mode 4 (default)
 | 20H Multiword DMA mode 0
 | 21H Multiword DMA mode 1
 | 22H Multiword DMA mode 2
 | 40H Ultra DMA mode 0
 | 41H Ultra DMA mode 1
 | 42H Ultra DMA mode 2
 | 43H Ultra DMA mode 3
 | 44H Ultra DMA mode 4
 | 45H Ultra DMA mode 5
 | 46H Ultra DMA mode 6
06H| Enable the PUIS feature set
07H| PUIS feature set device spin-up
10H| Enable use of SATA features
55H| Disable read look-ahead (read cache) feature
82H| Disable write cache
86H| Disable the PUIS feature set
90H| Disable use of SATA features
AAH| Enable read look-ahead (read cache) feature (default)
F1H| Report full capacity available

Note
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.

S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-5 Standard. SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. Users must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Table 9 S.M.A.R.T. commands

Note If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

Seagate Technology LLC
AMERICAS Seagate Technology LLC 47488 Kato Road, Fremont, California 94538, United States, 510-661-1000

• Publication Number: 100817550 Rev. N March 2023

References

• Warranty & Replacements | Support Seagate US
• The Leader in Mass Data Storage Solutions | Seagate US
• Contact Us | Seagate US
• Rescue Data Recovery Services | Seagate US
• Warranty & Replacements | Support Seagate US
• Rescue Data Recovery Services | Seagate UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>