INDESIT DF9E 1B10 S UK Slimline Dishwasher User Manual
- May 15, 2024
- INDESIT
Table of Contents
INDESIT DF9E 1B10 S UK Slimline Dishwasher
Product Information
Specifications
- Capacity: 9 standard place-settings
- Energy Consumption: Varies per program
- Water Consumption: Varies per program
FAQ
- How do I cancel an active cycle?
- To stop an active cycle, long press the START/PAUSE button to activate the DRAIN OUT function. The active program will be stopped, and the water in the dishwasher will be drained out.
- What should I do if water leaks during salt reservoir filling?
- If water leaks during filling, ensure the cap is screwed on tightly to prevent detergent from entering during the wash program.
THANK YOU FOR BUYING AN INDESIT PRODUCT
In order to receive a more complete assistance, please register your appliance on: www.indesit.com/register
Warning
- Before using the appliance carefully read Safety Instructions guide.
PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO HAVE MORE DETAILED INFORMATION
CONTROL PANEL
- On-Off/Reset button with indicator light
- Program selection knob
- Start/Pause button with indicator light / Drain out
FIRST TIME USE
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components.
- It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
- It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see PRODUCT DESCRIPTION) and must be filled when the green float on the cap of the salt reservoir is no longer visible.
- Remove the lower rack and unscrew the reservoir cap (anticlockwise).
- Only the first time you do this: fill the salt reservoir with water.
- Position the funnel (see figure) and fill the salt reservoir right up to its edge (approximately 1 kg); it is not unusual for a little water to leak out.
- Remove the funnel and wipe any salt residue away from the opening.
- Make sure the cap is screwed on tightly, so that no detergent can get into the container during the wash program (this could damage the water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the procedure before the beginning of the washing cycle to avoid corrosion.
FILLING THE RINSE AID DISPENSER
- Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be filled when the dark optical indicator on the dispenser door C becomes transparent.
- NEVER pour the rinse aid directly into the appliance tub.
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device D. Introduce the
detergent into the dry dispenser E only. Place the amount of detergent for
pre-washing directly inside the tub.
Usage of detergent not designed for dishwashers may cause malfunction or
damage to the appliance.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on heater, contributing also to better cleaning efficiency.
This system regenerates itself with salt, therefore it is required to refill
salt container when empty.
Frequency of regeneration depends on water hardness level setting –
regeneration takes place once per 5 Eco cycles with water hardness level set
to 3. Regeneration process starts in final rinse and finishes in drying phase,
before cycle ends.
- Single regeneration consumes: ~3.5L of water;
- Takes up to 5 additional minutes for the cycle;
- Consumes below 0.005kWh of energy.
PROGRAMS TABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020. Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor calibration.
The sensor calibration can increase program duration up to 20 min.
OPTIONS AND FUNCTIONS
Please scan the QR code on your product in order to have more detailed information.
DRAIN OUT: To stop and cancel the active cycle, the Drain Out function can be used. A long press of START/PAUSE button, will activate the DRAIN OUT function. The active program will be stopped and the water in the dishwasher will be drained out.
LOADING THE RACKS
CAPACITY: 9 standard place-settings
UPPER RACK
- Load delicate and light dishes: glasses, cups, saucers, low salad bowls.
- (loading example for the upper rack)
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
LOWER RACK
- For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should ideally be placed at the sides to avoid interferences with the spray arm.
- (loading example for the lower rack)
CUTLERY BASKET
The basket is equipped with top grilles for improved cutlery arrangement. The cutlery basket should be positioned only at the front of the lower rack. Knives and other utensils with sharp edges must be placed in the cutlery basket with the points facing downwards or they must be positioned horizontally in the tip-up compartments on the upper rack.
CLEANING AND MAINTENANCE
More information in the Daily Reference Guide on website.
CLEANING THE FILTER ASSEMBLY
- In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.) please remove them carefully.
- NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
CLEANING THE SPRAY ARMS
- To remove the upper spray arm, turn the plastic locking ring in a clockwise direction.
- The lower spray arm may be removed by pulling it upwards.
TROUBLESHOOTING
Please scan the QR code on your product in order to have more detailed information.
| PROBLEMS | POSSIBLE CAUSES | SOLUTIONS |
|---|
The dishwasher does not fill the water.
All LEDs are blinking rapidly.
| No water in the water supply or the tap is closed.| Make sure there is water
in the water supply or the tap running.
The inlet hose is bent.| Make sure the inlet hose is not bent ( see
INSTALLATION ) reprogram the dishwasher and reboot.
The sieve in the water inlet hose is clogged; it is necessary to clean it.|
After having carried out the verification and cleaning, turn off and turn on
the dishwasher and restart a new program.
The dishwasher finishes the cycle prematurely.
| Drain hose positioned too low or siphoning into home sewage system.| Check
if end of drain hose is placed at correct height (see INSTALLATION). Check for
siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply.| Check water supply for leaks or other issues letting air
inside.
More Information
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
- Using QR code on your product.
- Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
- Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our Aftersales Service, please state the codes provided on your product‘s identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>