BaByliss PRO BAB726U LO-PRO Trimmer User Manual

BaByliss PRO BAB726U LO-PRO

LO-PRO TRIMMER

Ergonomically designed, ultra-low profile, high torque metal trimmer for smooth powerful cutting and comfortable handling.

FEATURES

• High torque 6800 rpm brushless motor
• Metal housing with ultra-low profile design
• Ergonomic design for comfortable handling
• Advanced high-capacity lithium battery for up to 4 hours of cordless use
• Ultra-durable low friction, lower temperature PVD graphite coated zero-gap adjustable T-Blade
•  360° exposed T-Blade for total visibility
• Cord/cordless
• LED low battery indicator
• Cord/cordless

SAFETY CAUTIONS

Original instructions. Read these safety precautions carefully before using the unit! This appliance should only be used as described within this instruction booklet. Please retain for future reference.

IMPORTANT CHILD SAFETY

• ALWAYS keep out of the reach of very young children (during and after use).
• This appliance should not be used, cleaned or maintained by children.
• Always take extra care if used on children or near children.
• Do not use on very young children.

IMPORTANT SAFETY

• WARNING! Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
• Do not immerse the appliance in water or other liquids.
• Keep the appliance dry.
• UK Only: Do not use this appliance in the bathroom.
• Outside the UK: If using the appliance in a bathroom, unplug after use as the proximity of water can be dangerous even if the appliance is switched off. For additional protection the installation of a residual current device (RCD) with a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.
• The appliance’s charging stand and/or adaptor must be kept away from sources of water so that they do not fall into the water.
• CAUTION! Keep the power cord and the appliance dry. For appliances with a removable power supply unit, remove the power cord before cleaning.
• Always inspect the appliance before use for noticeable signs of damage. Do not use if damaged or if the appliance has been dropped. In the event of damage contact the Conair Customer Care Line (refer to ‘UK After Sales Service’ section for further information).
• Do not use the appliance if the charging adaptor or lead is damaged. In the event of damage, discontinue use immediately. If the charging adaptor or lead is damaged, it must be replaced by the manufacturer. Return the appliance to the Customer Care Centre (refer to ‘UK After Sales Service’ section for further information). No repair must be attempted by the consumer.
• Only use the attachments supplied with this appliance.
• WARNING! For the purposes of recharging the battery, only use the detachable charging supply unit provided with this appliance – (CA78M). This symbol indicates there is a detachable power supply for means of charging.
• Do not leave the appliance unattended when switched on.
• Do not leave the appliance plugged in for more than 24 hours.
• Unplug immediately if any problems occur during use.
• Do not place the appliance on any surface whilst in operation.
• Special care is required when using the appliance close to the ears, eyes and face.
• This appliance may be used by children aged from 8 and older and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction on the safe use of the appliance and understand the hazards involved. Children must not play with the appliance.
• This product contains a lithium ion rechargeable battery that is not to be removed from the appliance for charging. The batteries in this appliance are non-replaceable. Batteries must be disposed of safely at the end of life. Please take to a recycling centre for safe disposal. If the battery leaks, avoid touching it and dispose of it at a recycling centre.
• The supply terminals are not to be short circuited.
• This product complies fully with all appropriate EU and UK Legislation and the standards relevant to this type and class of appliance. We are an ISO9001:2015 certified company that continually evaluates our Quality Management System performance. If you have any queries regarding product safety and compliance, please contact the Conair Customer Care Line (refer to ‘UK After Sales Service’ section).

WEEE – END-OF-LIFE ELECTRICAL AND ELECTRONIC EQUIPMENT
In everybody’s interest and to actively participate in protecting the environment and human health:

• Do not discard your products with your unsorted household wastes.
• The WEEE (Waste electrical and electronic equipment) must be collected separately.
• Use the return and collection systems dedicated to the WEEE available in your area. In this way, some materials can be recycled, re-used or recovered.
• By ensuring this product is disposed of properly, you will help prevent potential negative consequences for the environment and human health due to possible content of hazardous substances.
• For more detailed information about the disposal of this product, please contact your local household waste disposal service.

TECHNICAL DATA

Vibration and noise levels

PREPARATION FOR USE General

• Always inspect the appliance before use to ensure the trimmer blades are free from hair, debris etc.
• Use on clean, dry hair that has been combed until tangle-free.

Oiling Instructions

• For optimum cutting performance, it is highly recommended to oil the blades after every use.
• When using the oil for the first time, unscrew the cap and cut off the very end of the plastic tube with a pair of scissors.
• Remove the blade guard and switch the appliance on.
• Holding the trimmer at a 45 degree angle, gently squeeze the oil tube and apply 2 drops directly onto the blades.
• Leave the unit on for a further few seconds to allow the oil to thoroughly spread along the length of the blades.
• Switch off the unit and remove any excess oil by gently dabbing with a cloth before using on hair.

INSTRUCTIONS FOR USE

Charging the Appliance

• Before using the appliance for the first time, charge the battery continuously for 3 hours. Maximum battery capacity will only be reached after 3 completed charging and discharging cycles.
• Plug the charging adapter into a suitable mains power socket and connect to the unit and switch on. The LED indicator light will flash when correctly connected to the mains power and will continuously flash until the battery has fully charged. When the battery is fully charged the LED indicator light will stop flashing but remain on.

NOTE: Always place the trimmer in the base with the ‘I/0’ switch in the OFF position.

• When the trimmer is running low on charge, the LED indicator light will flash, warning there is approximately 3 minutes of battery use remaining. A 3 hour charge will provide approximately 4 hours use.
• If the charging light starts to flash rapidly (more than 4 flashes per second) then the appliance is faulty. If this happens then please stop charging and remove the adapter from the mains and contact the Conair Customer Care Line. (See ‘UK After Sales Service’ section for further information).

Preserving the Batteries

• In order to maintain the optimum capacity of the rechargeable batteries, the appliance should be recharged for 3 hours approximately every 6 months.
• Using the trimmer on the mains – ensure that the trimmer is switched off. Plug into a suitable mains socket. Wait for approximately a minute, and then switch on.

IMPORTANT: Do not use the trimmer in this mode for more than 20 minutes.

REMOVING AND REPLACING THE BLADE

Ensure the trimmer isn’t connected to the mains and is switched off. Turn the trimmer upside down so that the teeth of the trimmer are facing down. Place the trimmer on a flat surface and using the screwdriver, loosen the fastening screws from the blade. Remove the blade from the trimmer (Fig. 1).

To install or replace your trimmer blade, reverse the procedure, aligning the blade cushion shaft into the moving blade cushion (Fig. 2). With the blade held in place, replace blade screws and tighten loosely. Turn the trimmer over and align the blade set parallel to the trimmer’s upper housing.

ZERO GAP ADJUSTMENT TOOL
IMPORTANT! Only attempt to zero gap the blades by using the adjustment tool and following the instructions very precisely.
The adjustment tool is required to adjust the blades to zero gap, which will achieve a closer, more precise cut.

• Step 1 – Using the screwdriver included, gently loosen the two small screws on each side of the blade.
• Step 2 – Slide the zero gap tool over the gold fixed blade until it is tight against the back portion of the moving cutting blade.
• Step 3 – Using your fingers on each side of the zero gap tool, push up until the cutting blade is even with or slightly below the fixed blade.
• Be sure that the blades are aligned properly. The teeth of the smaller blade (cutter) should rest slightly below the upper edge of the larger blade (comb) — approximately 0,5 mm to 1 mm apart (Fig. 3). If the blades are not correctly aligned, they may cut or scratch your skin when trimming. Once the blades have been aligned, tighten the screws firmly.
• Step 4 – WARNING! Make sure the moving cutting blade doesn’t extend past the fixed blade. If the cutting blade extends past the fixed blade it can potentially cut the skin.
• Step 5 – Once the blade is adjusted to zero gap or your liking, gently tighten the two screws on each side of the blade while holding the zero gap tool in place. If the blade is not adjusted to satisfaction after testing, repeat the adjusting process.

Cleaning & Maintenance

• To maintain optimum performance, the appliance should be cleaned after each use.
• Blow away any remaining hair on the blades or use the cleaning brush provided.
• Oil the blades after every use to ensure optimum cutting performance.

IMPORTANT: Blades must be cleaned and oiled on a regular basis for proper functioning. Failure to regularly clean and oil the blades will void the guarantee.
DO NOT RINSE BLADE, TRIMMER HANDLE OR ADAPTER

UK GUARANTEE
This BaByliss PRO appliance is guaranteed for professional use for 2 years and is only valid within the United Kingdom.
Exclusions
This guarantee will no longer be valid meaning that The Conair Group Ltd will not be liable to repair or replace your product where:

1. The appliance has been used on a voltage supply other than that which is marked on the product, or advised within this instruction booklet.

2. The appliance has been purchased from an unauthorised stockist*. 3.) Repairs or alterations have been attempted by unauthorised
   persons.

3. The failure of the appliance is a direct result of misuse.

4. The failure is a result of not following the instructions for use.7
   This guarantee does not cover any cosmetic damage due to misuse of the product nor any damage to persons or property that occurs because of product misuse.111111111

• unauthorized stockists include, but are not limited to online auction sites, private sellers and those selling second hand goods, refurbished products etc. Please contact the Conair Customer Care Line on 03705 133 191 (09:00 to 17:00 Monday to Friday) or e-mail ukinfo@conair.com for further information on authorised stockists.
• It is important to retain your proof of purchase. We recommend attaching your receipt to this page.
• Even where a refund may be applicable, no refund will be provided without a valid receipt or proof of purchase, we will only be able to offer a repair or replacement service. Please note this does not apply if the product was purchased directly from The Conair Group Ltd.
• Guarantees on replacement products run from the original purchase date or date of delivery, whichever is later, and not from the date of replacement.
• This guarantee is an additional benefit and does not affect your statutory rights as a consumer.
• If you have any queries regarding this guarantee please contact the Conair Customer Care Line on 03705 133 191 (09:00 to 17:00 Monday to Friday) or e-mail ukinfo@conair.com.
• UK AFTER-SALES SERVICE
• For further advice on using the appliance or should you need to return your product, please contact the Conair Customer Care Line on 03705 133 191 (09:00 to 17:00
• Monday to Friday) or e-mail your inquiry to ukinfo@conair.com.
• Return address:
• Customer Care Centre
• Conair Logistics
• Unit 4, Revolution Park
• Buckshaw Avenue
• Buckshaw Village
• Chorley
• PR7 7DW
• Please enclose your return number, name, and address details, together with a copy of proof of purchase and details of the fault.
• Please note this Instruction Booklet is not the guaranteed.

SAFE DISPOSAL

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be handed to an appropriate collection point for the recycling of Electrical and Electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about the recycling of this product, please contact your local council office or your household waste disposal service.

EU DECLARATION OF CONFORMITY DECLARATION UE DE CONFORMITY

• This declaration of confonnity is issued under the sole responsibility of the manufacturer
• La presente declaration de conformite est etabfie sous la seule responsabifite du fabricant soussigne
• Type of product / Type de produit Type number / Numero de type Trademark/ Marque
• With following characteristics
• Avec /es caraderistiques suivantes
• Countrv of oriain / Pavs d’oriaine
• Trimmer/ Tondeuse
• T178a
• BaByliss PRO/ Conair / CPL
• PRI: 100-240V-, 50-60Hz, 0.2A Max
• SEC: 4.5VDC, 1.2A, 5.4W
• China
• The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:
• L’objet de fa declaration d8crit ci-dessus est conforme a la /6gislation d’harmonisation de /’Union applicable:
• 2014/35/USE
• 2014/30/USE
• 2011/65/USE
• 2009/125/CE
• 2006/42/EC
• Low Voltage Directive / Directive base tension
• ElectroMagnetic Compatibility Directive / Directive concernant la compatibilite 8lectromagn8tique
• RoHS Directive and its amendments including (EU) 2015/863 / Directive RoHS et ses amendments don’t (UE) 2015/863
• Ecodesign Directives implemented by the Commission Regulations (EC) No. 1275/2008 amended by (EU) No. 801/2013 and (EC) No. 2019/1782 (where applicable) /
• Directive relative a l’ecoconception mise en ceuvre par Jes regtements de fa Commission (CE) No. 1275/2008 modifiee par (UE) No. 80112013 et (CE) No. 2019/1782 (le cas echeant) Machinery Directive / Directive Machine In accordance with the following standards: En accord avec /es normes suivantes:
• CE mark first affixed / Date de 19m appos1t1on du marquage CE: 04/2022
• Signed by and on behalf of / Signe par et au nom de: 2019;
• BABYLISS FACO S.R.L. (authorised by / autorise parBABYLISS S.A.R.L. and/ et The Conair Group Ltd)
• Avenue de l’lnd9pendance 25
• B-4020 Wandre, Belgium
• UKCA DECLARATION OF CONFORMITY In accorcltmce with UK Goi,ernment guic/1111ce
• We, the undersigned, take full responsibility for the product’s compliance.

• BoByliss FACO s.r.l. 25, Avenue de l’lndependonce B-4020 WANDRE BELGIQUE tr· {0032} 04 345 60 60 FAX: {0032} 04 345 60 BB Reg.Com.Lg 16.914 B.tE 0412.537.139 ‘V.A.BE0412.S37 39-Soc1ilt1Gine1ale BE846881 0043 92S9 Swt1 SGABBEBt

Documents / Resources

| BaByliss PRO BAB726U LO-PRO Trimmer [pdf] User Manual
BAB726U LO-PRO Trimmer, BAB726U, BAB726U Trimmer, LO-PRO Trimmer, Trimmer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>