SAMSUNG DV55CG7500 Smart Dryer User Manual

SAMSUNG DV55CG7500 Smart Dryer

Specifications

• Model Numbers: DVE(G)55CG7500, DVE(G)55CG7100, DVE(G)55CG7130*
• Control Panel: Included
• Special Features: SmartThings integration
• Vent Sensor: Available in DVE(G)55CG7500* models

Product Usage Instructions

Safety Information:

Congratulations on your new Samsung dryer. This manual contains important information on the installation, use, and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features.

What You Need to Know About the Safety Instructions:

Important safety symbols:

• WARNING: Hazards or unsafe practices that may result in severe personal injury, death, and/or property damage.
• CAUTION: Hazards or unsafe practices that may result in personal injury and/or property damage.
• NOTE: Indicates that a risk of personal injury or material damage exists.

These warning signs are here to prevent injury to yourself and others. Please follow them explicitly. After reading this manual, store it in a safe place for future reference. Read all instructions before using the appliance.

Installation

• What’s Included: Check the package contents to ensure all necessary components are present.
• Step-by-Step Installation: Follow the detailed installation steps provided in the manual for proper setup.
• Vent Blockage Test: Ensure proper ventilation by conducting a vent blockage test as instructed.
• Exhaust Ducting Guide: Properly set up the exhaust ducting following the guidelines provided.
• Switching the Door Position: If needed, refer to the manual for instructions on switching the door position for convenience.

Before You Start

• Sort and Load: Arrange and load the dryer with clothes as per the guidelines in the manual.
• Functional Prerequisite: Ensure all prerequisites are met before starting the dryer for optimal performance.

Operations

• Control Panel: Familiarize yourself with the control panel layout and functions.
• Simple Steps to Start: Follow the simple steps outlined to start using the dryer efficiently.
• Cycle Overview: Understand the different cycles available for various drying needs.
• Cycle Chart and Guide: Refer to the cycle chart and guide for selecting the appropriate drying cycle.

Maintenance

• *Vent Sensor (DVE(G)55CG7500 models only):** Utilize the vent sensor feature for enhanced safety and efficiency.
• Cleaning: Regularly clean the dryer as per maintenance instructions to ensure longevity.

Troubleshooting:

• Checkpoints: Refer to the troubleshooting section for common issues and solutions.
• Information Codes: Understand the information codes displayed for effective issue resolution.

Frequently Asked Questions

• Q: What should I do if I detect a gas smell?
  • A: In case you smell gas, immediately follow safety protocols and turn off the appliance. Contact a professional for assistance.
• Q: How often should I clean my dryer?
  • A: Regular cleaning is recommended based on usage frequency. Refer to the maintenance section for detailed cleaning instructions.

“`

Dryer
User manual
DVE(G)55CG7500/DVE(G)55CG7100/DVE(G)55CG7130*

Untitled-3 1

2023-10-05 3:11:05

Contents
Safety information What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING IMPORTANT SAFETY INSTRUCTIONS Warnings Cautions
Regulatory notice FCC Notice IC Notice Open Source Announcement
Installation requirements Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements Electrical requirements
Installation What’s included Step-by-step installation Vent blockage test Exhaust ducting guide Switching the door position
Before you start Sort and load Functional prerequisite RACK DRY (applicable models only)

Safety information

Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features.
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance. Please store the manual in a safe location close to the appliance for future reference. Use this appliance only for its intended purpose as described in this instruction manual. Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution and care when installing, maintaining and operating your dryer. Because the following operating instructions cover various models, the characteristics of your dryer may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or find help and information online at www. samsung.com.
Important safety symbols
What the icons and signs in this user manual mean:
WARNING Hazards or unsafe practices that may result in severe personal injury, death and/or property damage.
CAUTION Hazards or unsafe practices that may result in personal injury and/or property damage.
NOTE Indicates that a risk of personal injury or material damage exists.
These warning signs are here to prevent injury to yourself and others. Please follow them explicitly. After reading this manual, store it in a safe place for future reference. Read all instructions before using the appliance. As with any equipment that uses electricity and moving parts, potential hazards exist. To safely operate this appliance, familiarize yourself with its operation and exercise care when using it.

SAVE THESE INSTRUCTIONS
4 English

Untitled-3 4

2023-10-05 3:11:05

WARNING – Risk of Fire
· Clothes dryer installation must be performed by a qualified installer.
· Install the clothes dryer according to the manufacturer’s instructions and local codes.
· Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
· Do not install a booster fan in the exhaust duct. · To reduce the risk of severe injury or death, follow all installation
instructions. · Save these instructions.

Untitled-3 5

SAVE THESE INSTRUCTIONS
English5
2023-10-05 3:11:05

Safety information
WARNING – To reduce the risk of fire or explosion:
· Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed. There are many highly flammable items used in homes, such as acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers.
· Items containing foam rubber (which may be labeled latex foam) or similarly textured rubberlike materials must not be dried on a heat setting. Heated foam rubber materials can, under certain circumstances, ignite spontaneously.

SAVE THESE INSTRUCTIONS
6 English

Untitled-3 6

2023-10-05 3:11:05

WARNING – Fire or explosion hazard
· Failure to follow safety warnings exactly could result in serious injury, death or property damage.
· Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.
· Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
· Do not install a booster fan in the exhaust duct.
WARNING – What to do if you smell gas:
· Do not try to light any appliance. · Do not turn on the appliance. · Do not touch any electrical switch. · Do not use any phone in your building. · Clear the room, building or area of all occupants. · Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions. · If you cannot reach your gas supplier, call the fire department.
CALIFORNIA PROPOSITION 65 WARNING
WARNING
Cancer and Reproductive Harm – www.P65Warnings.ca.gov.

Untitled-3 7

SAVE THESE INSTRUCTIONS
English7
2023-10-05 3:11:06

Safety information
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, or other flammable or explosive substances, as they give off vapours that could ignite or explode. 3. Risk of Suffocation and Injury from Entrapment: Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children. 4. Before the appliance is removed from service or discarded, remove the door to the drying compartment. 5. Do not reach into the appliance if the drum is moving. 6. Do not install or store this appliance where it will be exposed to the weather. 7. Do not tamper with controls. 8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out. 9. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product. 10. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials. 11. Clean lint screen before or after each load. 12. Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. 13. The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel. 14. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of a tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. 15. Do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer). 16. (For Heat pump Clothes dryer) Sharp Edges ­ to reduce the risk of injury, use care when cleaning the condenser or evaporator coil fins.
SAVE THESE INSTRUCTIONS
8 English

Untitled-3 8

2023-10-05 3:11:06

Warnings
WARNING
· Ensure pockets are free of small, irregularly shaped hard objects and foreign material, i.e. coins, knives, pins, etc. These objects could damage your dryer.
· Gas leaks may occur in your system, resulting in a dangerous situation.
Cautions
CAUTION
· Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.
· Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside.
· Do not reach into the appliance when the drum is moving. · Do not install or store this appliance where it will be exposed to the weather. · Do not tamper with the controls. · Do not repair, replace, or attempt to service any part of the appliance unless specifically instructed to in
the user-repair instructions and you have the understanding and skills to carry out the procedure. · Do not use fabric softeners or products to eliminate static unless the softener or product is
recommended for dryer use by the manufacturer of the fabric softener or product. · Clean the lint screen before or after each load. · Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt. · The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. · This appliance must be properly grounded. Never plug the power cord into a receptacle that is
not grounded adequately or not in accordance with local and national codes. See the installation instructions for information about grounding this appliance. · Do not sit on top of the dryer. · Do not dry clothing with large buckles, buttons, or other heavy metal or solid objects. · Gas leaks may not be detected by smell alone. · Gas suppliers recommend you purchase and install a UL-approved gas detector. · Install and use in accordance with the manufacturer’s instructions. · Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even after being washed, these items may contain significant amounts of these oils.

Untitled-3 9

SAVE THESE INSTRUCTIONS
English9
2023-10-05 3:11:06

Safety information
· Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat from escaping and can create a fire hazard.
· All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous. Washing these items in hot water with extra detergent will reduce, but not eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their temperature. Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle. Never pile or stack these items when they are hot.

SAVE THESE INSTRUCTIONS
10 English

Untitled-3 10

2023-10-05 3:11:06

Regulatory notice
FCC Notice
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including interference that cause undesired
operation.
For products sold in the US and Canadian markets, only channels 1­11 are available. You cannot select any other channels.
FCC STATEMENT: This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorienting or relocating the receiving antenna · Increasing the separation between the equipment and receiver · Connecting the equipment to an outlet that is on a different circuit than the radio or TV. · Consulting the dealer or an experienced radio/TV technician for help.

Untitled-3 11

SAVE THESE INSTRUCTIONS
English11
2023-10-05 3:11:06

Regulatory notice
IC Notice
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of
the device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. For products sold in the US and Canadian markets, only channels 1­11 are available. You cannot select any other channels.
IC RADIATION EXPOSURE STATEMENT: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there is at least 8 inches (20 cm) between the radiator and your body. This device and its antenna(s) must not be colocated or operated in conjunction with any other antenna or transmitter.

SAVE THESE INSTRUCTIONS
12 English

Untitled-3 12

2023-10-05 3:11:06

Open Source Announcement
The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by contacting our support team via http://opensource.samsung.com (Please use the “Inquiry” menu.) It is also possible to obtain the complete corresponding source code in a physical medium such as a CDROM; a minimal charge will be required. The following URL http://opensource.samsung.com/opensource/SMART_AT_051/seq/0 leads to the open source license information as related to this product. This offer is valid to anyone in receipt of this information.

NOTE Hereby, Samsung Electronics, declares that the radio equipment type appliance is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: The official Declaration of conformity may be found at http://www.samsung.com, go to Support > Search Product Support and enter the model name. Wi-Fi max transmitter power : 20 dBm at 2.412 GHz ­ 2.472 GHz
SAVE THESE INSTRUCTIONS
English13

Untitled-3 13

2023-10-05 3:11:06

Installation requirements

Read through the following instructions before installing the dryer, and keep this manual for future reference.
WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the following parts while the appliance is energized: Control board and inlet valve.
Key installation requirements
· A grounded electrical outlet. · A power cord for electric dryers (except in Canada). · Gas lines (for gas models) that must meet national and local regulations. · An exhaust system made of rigid metal or flexible stiff-walled metal exhaust ducting.
WARNING Remove the door from all discarded appliances to prevent a child from suffocating.
Location considerations
· Adequate clearances between the dryer and adjacent walls or other surfaces. · Adequate air circulation for ventilation and gas combustion. · Away from water and weather.
WARNING · Make sure to exhaust the dryer outdoors to reduce the risk of fire. · Keep the dryer area clear of combustible materials, gasoline, and other flammable vapors and liquids. · Do not install other fuel-burning appliances around or in the same place as the dryer. · Place the dryer at least 18 in. (460 mm) above the floor for garage installation.

14 English
Untitled-3 14

2023-10-05 3:11:06

Dimensions

A U

Dimensions (in. (mm))

9
Type Model
A. Overall height B. Width
C. Depth with door open D. Depth

Front loading dryer DVE(G)55CG7500 / DVE(G)55CG7100
/ DVE(G)55CG7130* 45.8 (1163) 27.0 (686) 50.1 (1273) 30.2 (768)

Untitled-3 15

English15
2023-10-05 3:11:06

Installation requirements

Clearance requirement This clearance requirement is applicable for dryers only.
NOTE · For washer’s clearance requirement, see the washer’s user manual. · If the washer and dryer have different clearance requirements, use the one with the larger value.
Alcove or closet installations
WARNING · The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or
closet. · No other fuel-burning appliance should be installed in the same closet as the dryer. · Place the dryer at least 18 in. (460 mm) above the floor for garage installation. Minimum clearance for stable operation:

Sides 1 in. / 25 mm

Top 17 in. / 432 mm

Rear 4.0 in. / 102 mm

Front 1 in. / 25 mm

If both the washer and a dryer are installed in the same location, the front of the alcove or closet must have two unobstructed air openings for a combined minimum total area of 72 in.² (465 cm²).

16 English
Untitled-3 16

2023-10-05 3:11:06

This clearance requirement is applicable for washer and dryer pair installation. Side by side installation
B

A

A

A

1 in. (25 mm)

B

21 in. (533 mm)

C

1 in. (25 mm)

D

4.0 in. (102 mm)

C

D

Untitled-3 17

English17
2023-10-05 3:11:06

Installation requirements

Ducting requirements

Recommended

Use only for short-run installation

Weather hood type

No. of 90° elbows 0 1 2 3

4″ (10.2 cm) Rigid
80 ft. (24.4 m) 68 ft. (20.7 m) 57 ft. (17.4 m) 47 ft. (14.3 m)

2.5″ (6.4 cm) Rigid
74 ft. (22.6 m) 62 ft. (18.9 m) 51 ft. (15.5 m) 41 ft. (12.5 m)

NOTE * Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.
If you integrate the dryer’s vent system with an existing exhaust system, make sure: · The exhaust system meets all applicable local, state, and national regulations. · Not to use a flexible plastic duct. · To regularly check and clean all lint buildup from inside the existing ducts. · The duct is not kinked or crushed. · The exhaust hood damper opens and closes freely.
Manometer measurements The static pressure in any exhaust system must not exceed 0.83 inches of water column or be less than 0. Note that these values are measured with the dryer running with a manometer presented to the exhaust duct that connects to the dryer. The dryer tumbler must be empty and lint filter clean.

18 English
Untitled-3 18

2023-10-05 3:11:07

Exhausting requirements
The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room.
In the United States and Canada · All dryers must be exhausted to the outside. · The required exhaust duct is 4 inches (10.2 cm)
in diameter. · See “Ducting requirements” in the
“Installation” section for the maximum duct length and number of bends that can be used. · The total length of flexible metal duct must not exceed 7′ 10 1/2″ (2.4 m). · Do not assemble the duct with screws or other fastener means that extend into the duct and catch lint. · For the United States only: Use only those foiltype flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct. Use Subject 2158A.

Outside the United States and Canada · Refer to the local codes.
WARNING
· You must exhaust the dryer to the outside to reduce the risk of fire when you install the dryer in an alcove or closet.
· Do not use a plastic or non-metal flexible duct. · If your existing ductwork is plastic, non-metal,
or combustible, replace it with metal. · Use only a metal exhaust duct that is non-
flammable to ensure containment of exhaust air, heat, and lint.

Untitled-3 19

English19
2023-10-05 3:11:07

Installation requirements

Gas requirements
WARNING
· Use only natural or LP (liquid propane) gases. · The installation must be conformed with local
codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision (for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1 (for Canada). · Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician. (LNG models only) You must check the burner of your model and use the proper LP Kit accordingly. To check the detail information of the burner, open the door and check the rating label location on the door frame.
– 20,000 BTU: LPKIT-4/XAA (DC98-04114A) – 22,000 BTU: LPKIT-3/XAA (DC99-00792A) · A 1/2″ (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8″ (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off valve be installed within 6″ of your dryer. · Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor. · Additionally, a 1/8″ (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must be installed immediately upstream of your dryer’s gas supply connection. · Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system.

· Do not reuse old flexible metal gas lines. Flexible gas lines must be designed and certified by the standard for connectors for Gas Appliances, ANSI Z21.24 · CSA 6.10.
NOTE
· Your dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot.
· Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.
· As a courtesy, most local gas utilities will inspect a gas appliance installation.
Commonwealth of Massachusetts installation instructions Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the connector can be no longer than 3′ (36″).
WARNING
· Gas leaks may occur in your system, creating a dangerous situation.
· Gas leaks may not be detected by smell alone. · Gas suppliers recommend you purchase and
install a UL-approved gas detector. · Install and use in accordance with the
manufacturer’s instructions.

20 English
Untitled-3 20

2023-10-05 3:11:07

Electrical requirements
The wiring diagram is located on the plate under the control panel or rear frame.
WARNING
· Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer ­ if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
· To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding must be done in accordance with local codes, or in the absence of local codes, in accordance with the National Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 ­ Latest Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical service for your dryer.
· All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 ­ Latest Revision (for the U.S.) or CAN/CGA ­ B149 Installation Codes ­ Latest Revision (for Canada) and local codes and ordinances.

Grounding This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current.
Gas models
WARNING
· Your dryer has a cord with an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
· Do not modify the plug provided with your dryer ­ if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
· Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.
Electric models
WARNING
· Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug. This cord is sold separately.
· The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
· Do not modify the plug provided with your dryer ­ if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
· If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dryer.

English21

Untitled-3 21

2023-10-05 3:11:07

Installation requirements

Electrical connections Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord.
Gas models ­ U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required.
Electric models ­ U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some require 120 / 208 volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of the line is required. · If a power cord is used, the cord should be
plugged into a 30-ampere receptacle. · The power cord is not provided with U.S.
electric model dryers. This cord is sold separately.

WARNING
Risk of Electric Shock When local codes allow, you can connect the dryer’s electrical supply with a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120 / 240 volts, 30-amperes with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads. · Do not reuse a power supply cord from an old
dryer. The power cord electric supply wiring must be supported at the dryer cabinet by a suitable UL-listed strain relief. · Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. (Use a 4-prong plug for a 4 wire receptacle, NEMA type 14-30R.)
Electric models ­ Canada Only A 120 / 240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker on both sides of the line is required.
NOTE
All Canadian models are shipped with the power cord attached. The power cord should be plugged into a 30-ampere receptacle. In Canada, you may convert a dryer to 120 / 208 volts.

22 English
Untitled-3 22

2023-10-05 3:11:07

Installation

This dryer must be installed by a qualified technician. The installer is responsible for connecting the dryer to the main power while observing the relevant safety regulations of your area.
What’s included
Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer.
01 02
04 03

01 Control panel 04 Door

05
02 Worktop 05 Exhaust duct

03 Lint filter

Untitled-3 23

English23
2023-10-05 3:11:07

Installation
Parts supplied

Y-connector Tools needed for installation

Water hose (Canadian elec. models only)

Short water hose

Pliers

Cutting knife

Pipe wrench (gas models only)

Nut driver

Level

Phillips screwdriver

Duct tape

Wrench

LPG-safe compound or Teflon Tape (for gas
installation)

Gloves

WARNING
Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.

24 English
Untitled-3 24

2023-10-05 3:11:08

Step-by-step installation
Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. · Do not remove the protective film on the door before completing the product installation. If you remove
the protective film before the installation is complete, the door may get scratched or damaged during installation. · Make sure the installation location allows enough space for the dryer door to be fully open.
STEP1Install the exhaust system
1. Select a location and move the dryer to the site. For easy access, we recommend you install the dryer in the same location as your washer.
2. To change the door direction, see “Switching the door position” on page 34. 3. Install the exhaust system as instructed in the “Exhaust ducting guide” section.
CAUTION Before installing your dryer, remove the packing in the duct.
NOTE · To move the dryer easily, lay two of the carton cushion-from the packaging on the floor. Tip the dryer on
its side so it lies across both cushion-tops. Push the dryer so that it is near its final location, and then set the dryer upright. · Secure room around the dryer to facilitate ducting and wiring.
STEP2Connect the gas line (for gas models)
Before connecting the gas line, make sure you have read the “Gas requirements” section on page 20. 1. Remove the protective cap from the gas pipe. 2. Apply an LPG (Liquefied Petroleum Gas)-safe compound or 1.5 wraps of Teflon tape to all threaded
connections. 3. Connect the gas supply to the dryer. An additional fitting is required to connect the 3/4″ (1.9 cm) female
thread end of a flexible connector to the 3/8″ (1 cm) male threaded end on the dryer. Tighten up the fitting over all threads. 4. Turn on the gas supply, and check for any leaks using a soap solution. If a leak is found, tighten the connections and try again. Do not use an open flame to check for gas leaks.

Untitled-3 25

English25
2023-10-05 3:11:08

Installation

STEP3Connect the electrical wiring (for electric models) Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 21.
3-wire system

D

A B C L2

L1 E

A. External ground connector B. Neutral grounding wire (white) C. Center silver-colored terminal block
screw D. Neutral wire (white or center wire) E. 3/4″ (1.9 cm) UL-listed strain relief

1. Loosen or remove the screws from the center terminal block.
2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block. Tighten the screws.
3. Connect the other wires to outer terminal block screws. Tighten the screws.
4. Tighten the strain relief screws. 5. Insert the terminal block cover into the rear panel of
the dryer. Then, secure the cover with a hold-down screw.
CAUTION
· To convert from the 4-wire system to 3-wire system, connect the ground strap to the terminal block support to ground the dryer frame to the neutral conductor.
· Ring-type terminals are recommended. If using strap terminals, make sure they are tightened.
· Connect the power cord and check L1/L2/N voltage. If the voltage is low, it may not heat properly. Review the “Electrical requirements” section on page 21 if needed.

26 English
Untitled-3 26

2023-10-05 3:11:08

4-wire system

F D

A B C L2

L1 E

A. External ground connector B. Neutral grounding wire (white) C. Center silver-colored terminal block
screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief F. Neutral wire (white or center wire)

1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw.
CAUTION – To connect the ground wire to the neutral position
without through contact A (cabinet ground), contact a technician. This is not user serviceable. – Ring-type terminals are recommended. If using strap terminals, make sure they are tightened. 2. Loosen or remove the screws from the center terminal block. 3. Connect the neutral wire (white or center wire) and ground wire (white) to the center screw of the terminal block. Tighten the screw. 4. Connect the other wires to the outer terminal block screws. Tighten the screws. 5. Tighten the strain relief screws. 6. Insert the tab of the terminal block cover into the rear slot of the dryer. Secure the cover with a holddown screw.

CAUTION
Connect the power cord and check L1/L2/N voltage. If the voltage is low, it may not heat properly. Review the “Electrical requirements” section on page 21 if needed.
WARNING
· All U.S. models are designed for a 3-wire system connection. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-wire system connection is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block.
· Remove the terminal block cover plate. Insert the power cord with a UL- listed strain relief through the hole provided in the cabinet near the terminal block.
· A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8″ (1 cm) deep well socket.
· Since january 1, 1996, The national electric code requires that new wiring (not existing) utilize a 4-wire connection to this dryer.

Untitled-3 27

English27
2023-10-05 3:11:08

Installation
STEP4Connect the water hose
The dryer must be connected to a cold water tap using the provided water hoses.
1. Connect the angled end of the water hose to the filling valve at the bottom of the rear frame. Turn the coupling manually until it is tight.
2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten because the coupling may be damaged.
3. If you detached the cold water hose from your washer, attach the hose to the open end of the Y-connector, tighten the coupling by hand until it is tight, and then, using a pliers, tighten an additional two-thirds turn.
4. Open the cold water tap, and then check for any leaks.
If the Y-connector cannot be directly connected to the cold water tap, use the short hose. See the “Using the short hose as an extension” section on page 29.

28 English
Untitled-3 28

2023-10-05 3:11:09

Using the short hose as an extension
B A C

1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight.
2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten because the coupling may be damaged.
3. Connect the Y-connector (A) to the short hose. Turn the coupling by hand until it is tight.
4. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten because the coupling may be damaged.
5. Connect the angled end of the water hoses (C) to the filling valve at the bottom of the rear frame. Turn the coupling manually until it is tight.
6. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten because the coupling may be damaged.
7. If you detached the cold water hose from your washer, attach the hose to the free end of the Y-connector, tighten the coupling by hand until it is tight, and then, using a pliers, tighten an additional two-thirds turn.
8. Open the cold water tap, and then check for any leaks.

Untitled-3 29

English29
2023-10-05 3:11:09

Installation
STEP5Level the dryer To ensure optimal performance, the dryer must be level.
Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling feet (B) clockwise to lower the dryer or counterclockwise to raise the dryer.
A

B

A

B

NOTE
· To set the dryer to the same height as your washer, fully retract (A) the leveling feet by turning them counterclockwise, then loosen (B) the feet by turning them clockwise. Once the dryer is the same height as the washer, follow the directions above to level the dryer.
· Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.

30 English
Untitled-3 30

2023-10-05 3:11:09

STEP6Power on (for gas models)
Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7 below.
STEP7Final check
When installation is complete, confirm that: · The dryer is plugged into an electrical outlet and grounded properly. · The exhaust ductwork is connected, and the joints are taped. · You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct. · The dryer is level and is sitting firmly on the floor. · The dryer starts, runs, heats, and shuts off properly.
For gas models: · The gas is supplied properly with no leaks (For gas models only).
CAUTION The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the exhaust for heat.

Untitled-3 31

English31
2023-10-05 3:11:09

Installation
Vent blockage test
After the dryer is installed, start the Vent Blockage Test to check if the duct system is properly installed. The Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy.
NOTE
The Vent Blockage Test must run when the dryer is cool. If the dryer warms up after the installation check, run the AIR FLUFF cycle for several minutes to reduce its internal temperature.
Running the vent blockage test 1. Make sure the drum is empty, and then close the door. (If there are any clothes or other items in the
drum, the test will not give accurate results.)
2. Press the Power button to turn the dryer on, then simultaneously press and hold the Adjust Time and Dryness buttons for 3 seconds. “InS or In” appears in the dryer’s display. (If you have started other procedures before the Vent Blockage Test, the dryer will not enter the Vent Blockage Test mode.)
3. Press the Start/Pause (Hold to Start) button. The Vent Blockage Test starts immediately. During the test, the number indicator makes a circle in 6 clockwise steps. The test takes about 2 minutes. Do not open the door during the test.
4. After 2 minutes, when the test is complete, the results are displayed and the dryer sounds a tone. If status of the duct system is normal, “0” appears and the dryer sounds a completion tone. If the duct system cannot exhaust properly, the check code appears, and the dryer sounds an alarm tone. For description about the code, see the “Installation check codes” section on page 33. If there are any other problems, an information code appears in the display. For description about the code, see the “Information codes” section on page 57. – To stop or cancel the Vent Blockage Test, press the Power button to turn off your dryer. – The results remain on the display for about 5 minutes and then automatically turn off. You can turn the results off immediately by pressing the Power button.
NOTE
· During or after the test, the internal drum is hot. Use caution to prevent burns. The Vent Blockage Test is used to check for problems in the current duct system when the dryer is installed for the first time.
· If the test result displays check code (the duct system is blocked ), refer to the “Ducting requirements” section on page 18 and the “Exhaust ducting guide” section below, and then take proper measures to correct any problems. If the test is suspended, it could result in incorrect results. Follow the proper procedures when testing the dryer.
· Even if the test result is normal (“End or 0”), the duct system could be blocked slightly. Properly install all duct work according to the installation instructions in this manual.

32 English
Untitled-3 32

2023-10-05 3:11:09

Installation check codes

Check code 0 Clg (Cg) C80 (C8) C90 (C9)
Ct tC C1
dC
9C1
HC

Meaning

Solution

Vent condition is good.

The vent is clogged.

About 80 % of the vent is clogged. (This may decrease the drying performance.)
Over 90 % of the vent is clogged. (This may lead to poor drying performance or cause malfunction)

1. Clean the lint filter. 2. Check your vent condition. (Refer to the
“Ducting requirements” section) * You must take measures (such as cleaning) through expert personnel.

The internal temperature of the dryer is too low (below 32 °F (0 °C)) or too high (over 104 °F (40 °C)) and therefore vent blockage cannot be detected.

Leave the dryer at room temperature (41~95 °F (5~35 °C)) for an hour and check again.

Temperature sensor error

Contact a service center.

Unit is detecting items inside the drum or there is an error on the dry sensor.

Remove items from the drum and check again.
If the problem continues, contact a service center.

Unit is detecting door is open

Close the door properly and check again. If the problem continues, contact a service center.

Abnormal voltage detected

Check the power connection. (Refer to the “Connect the electrical wiring (for electric models)” section)
If the problem continues, contact a service center.

Detection of abnormal temperature in drum.

Check the power connection. Check the vent condition if the problem continue, contact a service center.

Untitled-3 33

English33
2023-10-05 3:11:09

Installation
Exhaust ducting guide
Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping
screws. 3. To facilitate the exhaust, keep the ducts as straight as possible.
Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely. We recommend that you to clean the exhaust system annually or on a regular basis.
WARNING · To prevent fire, do not use plastic, thin-foil, or non-metal flexible ducts of any kind. · Do not use a poor exhaust system because it slows down the dryer’s performance. · Do not use excessively long ducts that have multiple elbows. · Do not use crushed or clogged venting or ducts.
Switching the door position
To reverse the direction of the door, we recommend that you contact a qualified technician. 1. Put a soft rug on the floor to rest the door on after
you have removed it. This will prevent the door from being scratched. 2. Unplug the power cord of the dryer. 3. Remove the four hinge screws from the door, and then remove the door by lifting it up slightly.
4. Remove the two screws from the lever holder, and then remove the holder cover.
5. Put the lever holder on the other side as shown, and then tighten the screws. Install the holder cover on the opposite side as shown.

34 English
Untitled-3 34

2023-10-05 3:11:09

6. Use a flat-head screwdriver to remove the two hinge covers from the original side. Install the hinge covers on the opposite side as shown.
7. Locate and remove the 10 screws as shown. Note that screw B (x2) is longer than the others.
B
8. Remove the glass holder, and switch the positions of: a. the hinge cover and the door handle. b. the hinge holder and the glass-guide holder
9. Remove the door lever, and then move it to the other side as shown.

Untitled-3 35

English35
2023-10-05 3:11:09

Installation
B

10. Remove the hole cover (C), and then insert and tighten the glass holder using the removed 10 screws.
11. Install the hole cover on the opposite side as shown.
C

12. Reinstall the door on the front frame, and then carefully insert and tighten the 4 hinge screws.

36 English
Untitled-3 36

2023-10-05 3:11:10

Before you start

Here are a few things you should know before starting your dryer.

Sort and load
· Put one wash load in the dryer at a time. · Do not mix heavy and lightweight items
together. · To improve drying efficiency for one or two
items, add a dry towel to the load. · For best results, untangle items before
inserting them into the dryer. Tangled items may degrade the drying efficiency or cause the door to open.

· Overloading reduces the tumbling performance, resulting in uneven drying and wrinkling.
· Unless recommended on the care label, do not dry woolens or fiberglass items.
· Avoid drying unwashed items. · Do not dry items soiled with oil, alcohol,
gasoline, etc.

Functional prerequisite

Lint filter

To prevent a risk of fire, make sure to clean the lint filter before or after every load. 1. Turn off the dryer. 2. Open the door and pull out the lint filter (A) from
inside the drum. 3. Remove the lint, and then clean the lint filter. 4. Reinsert the lint filter, and then close the door.

A

CAUTION

· Do not operate the dryer without the lint filter in place.
· Do not use a damaged or broken lint filter. This may reduce performance and/or cause fire.

Untitled-3 37

English37
2023-10-05 3:11:10

Before you start

RACK DRY (applicable models only)
Some models come with a drying rack which is inserted into the drum at the factory. If your model came with a drying rack, remove the rack from the drum before you use the dryer for the first time. To remove the rack, pull the rack straight up, and then take it out of the drum. Remove the drying rack from its packaging and store the rack for later use.

If a drying rack is not provided, you can purchase it at a local Samsung service center. (Part Code : DC93-

00374H)

To use the drying rack, follow these steps:

1. Insert the drying rack (A) inside the tumbler with the

filter handle to the front.

2. Insert the rear legs of the drying rack into the

recessed areas of the rear wall, and then press down

the middle of the drying rack to secure it in place.

3. Put items to dry on the rack. Make sure to leave

A

space between the items for air flow.

4. Press RACK DRY or other Cycle Setting according to rack drying suggestions below, then select the drying

time.

5. When the items are dry, remove the them from the

dryer, and then remove the drying rack.

38 English
Untitled-3 38

2023-10-05 3:11:10

Drying rack drying suggestions
Item Washable sweaters (fold sweater into same shape
as rack and lay it flat on the rack) Stuffed toys (cotton or polyester fiber- filled)
Stuffed toys (foam or rubber-filled) Foam rubber pillows Sneakers

Cycle settings TIME DRY with the Low temperature setting
AIR FLUFF

WARNING
· Make sure to unpack the drying rack before using it. Otherwise, the dryer can be damaged or its performance diminished.
· Drying foam rubber, plastic, or rubber on a heat setting may damage the items and create a fire hazard.

Untitled-3 39

English39
2023-10-05 3:11:10

Operations

WARNING To reduce the risk of fire, electric shock, or injury to persons, read the “Safety information” before operating this appliance.
Control panel
DVE55CG7500*

02 01

07

10

12 08

09

11 13

DVG55CG7500*
01

03

04 05 06

02

07

10

12 08

09

11 13

DVE55CG7100 / DVE55CG7130
01

03

04 05 06

02

07

10

12 08

09

11 13

03

04 05 06

40 English
Untitled-3 40

2023-10-05 3:11:10

DVG55CG7100 / DVG55CG7130
01

02

07

08 09

03

04 05 06

10 12
11 13

01 Cycle Selector 02 Digital Graphic
Display 03 Dryness
04 Temp.

Turn the Cycle Selector to select a desired cycle. When a cycle is selected, the cycle indicator lights up. · Steam Cycles: The dryer sprays water into the drum to deodorize clothes
and reduce static electricity and wrinkles. · Manual Dry: The drying time is fixed.
Displays all cycle information, including the cycle time, information code, and operating status.
Press to select a dry level. You can select from 5 different options (Less to More). Please refer to following recommendations to select the appropriate dryness. · For larger or bulkier loads, select More for complete dryness. · For items that needs to lay flat or hang to dry, use Less to partially dry
items.
NOTE
This option is not available with REFRESH, STEAM SANITIZE, ACTIVEWEAR, TIME DRY, QUICK DRY, and AIR FLUFF.
Temperature can only be adjusted in TIME DRY cycle. Press to change the temperature of the current cycle. You can select from 5 different options (Low to High). Please select the appropriate temperature depending on the items in the load. · High: For sturdy cottons or those labeled Tumble Dry. · Medium: For permanent press, synthetics, lightweight cottons, or items
labeled Tumble Dry Medium. · Low: For heat sensitive items labeled Tumble Dry Low or Tumble Dry
Warm. Provides the lowest heated drying temperature possible.

Untitled-3 41

English41
2023-10-05 3:11:11

Operations

05 Time
06 Wrinkle Prevent
07 Eco Dry
08 Damp Alert
09 Drum Light
10 Adjust Time 11 Smart Control
(Electric models only) / Smart Monitor (Gas models only) 12 Power 13 Start/Pause (Hold to Start)

Press to adjust the drying time for the Manual Dry cycles. This is not available with the Sensor Dry cycles because the dryer determines the drying time by sensing the current moisture level of the load.
Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Press Wrinkle Prevent to activate this feature. The load is dry, and can be removed at any time during the Wrinkle Prevent cycle.
This function is available with NORMAL and TIME DRY. With the Eco Dry activated, drying takes a longer time but the power consumption is reduced. The drying time can be extended by up to 3 times depending on the temperature and load. (See the “Cycle chart” on page .)
This alert is available for all Sensor Dry cycles except for ACTIVEWEAR. Available dry levels are Normal, More, and Extra. If a load contains mixed fabrics, the Damp Alert indicator blinks when average dryness of the items in the load is 80 % dry. This lets you take items that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry.
Press to turn the interior lamp on or off. The lamp stays lit for 2 minutes after it has turned on, regardless of whether the power is on or off or the door is open or closed, and then turns off automatically.
You can change the set time in the Manual Dry cycles. (QUICK DRY, TIME DRY, and AIR FLUFF) To change the cycle time, press or until the desired time is displayed.
After connecting the Tumble Dryer to your home network using the Samsung Smart Washer/Dryer app, you can control or monitor the dryer remotely. When started, the Smart Control (Smart Monitor) indicator blinks. The dryer enters waiting mode and waits for remote commands.
Press to turn on/turn off the dryer.
Press to start or stop operation.

NOTE Do not take extremely tangled items from your washer and put them into the dryer. They can degrade the drying efficiency of the dryer or cause the door to open. We recommend that you untangle the items before putting them into the dryer. Also, do not put objects on the dryer, especially on the control panel.
CAUTION Do not spray water directly onto the control panel. This may cause a system failure.

42 English

Untitled-3 42

2023-10-05 3:11:11

Icon description

Sensor Dry
Filter Check Vent Sensor (DVE(G)55CG7500* models only) Steam
Child Lock Sound Off

This icon appears when the dryer operates the cycle which senses the internal humidity to determine the drying time.
This icon displays after every load as a reminder to clean the lint filter. Clean the lint filter before every cycle and make sure the filter is properly inserted before starting a cycle.
The dryer features a vent sensor that detects and notifies you when it is time to clean the ductwork. The indicator lets you know the status of the duct.
This icon appears when the dryer is in steam process. The dryer sprays water into the drum to deodorize clothes and reduce static electricity and wrinkles.
This icon indicates that Child Lock is on. For more information on Child Lock, see page 49.
This icon indicates that the alarm is off. For more information on Sound Off, see page 49.

Wi-Fi

This icon indicates that the dryer is connected to Wi-Fi.

Untitled-3 43

English43
2023-10-05 3:11:11

Operations

Simple steps to start
1. Press Power to turn the dryer on. 2. Turn the Cycle Selector to select a cycle. 3. Change the cycle settings (Dryness, Temp., and Time) as necessary. 4. Select desired options as necessary. 5. Press and hold Start/Pause (Hold to Start).
To change the cycle during operation 1. Press Start/Pause (Hold to Start) to stop operation. 2. Select a different cycle, and repeat steps 2-4 above if necessary. 3. Press and hold Start/Pause (Hold to Start) again to start the new cycle.
Cycle overview

Standard Cycles Cycle
NORMAL HEAVY DUTY
ACTIVEWEAR
PERM PRESS DELICATES BEDDING
DOWNLOADED

Description
For most fabrics including cottons and linens. If NORMAL is selected, the Eco Dry function is enabled. For more information, see Eco Dry in the “Control panel” section.
For drying items made out of heavy fabrics, such as jeans, corduroys, or work clothes, with high temperature heat.
For exercise wear and outdoor wear such as sports jerseys, training pants, water-repellent jackets, and other performance clothing. Thick fabrics like a zipper or velcro closure of a jacket, or training socks may not be completely dried.
For drying wrinkle-free cottons, synthetic fabrics, knits, and permanent press fabrics automatically.
For heat-sensitive items at a low drying temperature.
For bulky items such as blankets, sheets, and comforters.
· Select to choose from more cycles available on the Samsung Smart Washer/Dryer app on your smartphone.
· Available cycles: ECO NORMAL, SHIRTS, DENIM, TOWELS, RACK DRY, WRINKLE AWAY, SANITIZE, WOOL, LOW TEMP.
· Factory setting: WRINKLE AWAY

44 English
Untitled-3 44

2023-10-05 3:11:11

Manual Dry You can change the drying settings manually to your preference.

Cycle QUICK DRY
TIME DRY AIR FLUFF

Description
A quick drying cycle running for 30 minutes. The default cycle time is 30 minutes. However, you may manually change the cycle time if necessary.
You can specify a cycle time in minutes. If TIME DRY is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Control panel” section.
Tumbles the load in room temperature air.

Steam Cycles Use steam to reduce wrinkling and odors on items.

Cycle STEAM SANITIZE
REFRESH

Description
Use to sanitize items by applying steam and high-temperature heat to the fabric. This cycle can make items soft and reduce smells. Confirm that the laundry load is wet or partially wet before starting this cycle.
Use to smooth out wrinkles and reduce odors in loads of one to four items. With this cycle selected, a small amount of water is sprayed into the dryer drum after several minutes of tumbling with heat. Confirm that the laundry load is dry.

Untitled-3 45

English45
2023-10-05 3:11:11

Operations

Cycle chart

NOTE
For best results, follow the load size recommendations for each dry cycle. · Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble
freely. · Medium load : Fill the drum to about 1/2 full. · Small load : Fill the drum with 3-5 items, not more than 1/4 full.

Cycle NORMAL HEAVY DUTY ACTIVEWEAR PERM PRESS DELICATES BEDDING QUICK DRY TIME DRY AIR FLUFF STEAM SANITIZE REFRESH

Recommended items Cottons, work clothes, linens, mixed loads
Heavy fabrics such as jeans, corduroys, heavy work clothes Water-repellent wear, performance clothes, sports wear
(Maximum : 4 lbs) Shirts, synthetic fabrics, knits, wrinkle-free cottons, permanent
press Underwear, blouses, lingerie
Bulky items such as blankets, sheets, comforters, pillows Small loads Any load
Foam,rubber, plastic Bedding, curtains, children’s clothing Shirts, trousers, comforters, pillows

Load size

Dry level Normal dry (Adjustable) Normal dry (Adjustable) Normal dry (Not adjustable) Normal dry (Adjustable) Normal dry (Adjustable) Normal dry (Adjustable)
–
–
–
Very dry (Not adjustable)
–

46 English
Untitled-3 46

2023-10-05 3:11:12

NOTE : factory setting, : can be selected

Cycle
NORMAL HEAVY DUTY ACTIVEWEAR PERM PRESS DELICATES
BEDDING QUICK DRY TIME DRY AIR FLUFF STEAM SANITIZE REFRESH

High

Functions (Temp. Control)

Time Low

Cycle
NORMAL
HEAVY DUTY ACTIVEWEAR PERM PRESS
DELICATES BEDDING QUICK DRY TIME DRY AIR FLUFF STEAM SANITIZE REFRESH

Adjust Time

Damp Alert

Options
Eco Dry
: DVE(G)55CG7100 / DVE(G)55CG7130
models : DVE(G)55CG7500*
models

Wrinkle Prevent

Untitled-3 47

English47
2023-10-05 3:11:12

Operations

Cycle guide

The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference.

Cycle

Description

Bedspreads & Comforters

Follow the care label instructions or dry using BEDDING. · Make sure the item is thoroughly dry before using or storing. · May require repositioning in the drum to ensure even drying.

Blankets

Use NORMAL and dry only one blanket at a time for best tumbling action. · Make sure blankets are thoroughly dry before using or storing.

Curtains & Draperies

Use PERM PRESS and the Medium temperature setting to help minimize wrinkling.
· Dry curtains and draperies in small loads for best results and remove as soon as possible.

Cloth Diapers

Use NORMAL and the Medium temperature setting for soft, fluffy diapers.

Down­filled Items (jackets, sleeping bags, comforters, etc.)

Use NORMAL and the Medium temperature setting. · Add a couple of dry towels to absorb moisture and shorten drying time.

Foam Rubber (rug backs, stuffed toys, shoulder pads, etc.)

Do not dry on a heat setting. WARNING
Drying a rubber item with heat may damage it or cause a fire.

Pillows

Use NORMAL.
· Add a couple of dry towels and a pair of clean sneakers to help the tumbling action and to fluff the items.
· Do not dry kapok or foam pillows using a heated drying cycle.

Plastics (shower curtains, outdoor furniture covers, etc.)

Use TIME DRY and the Low or Extra Low temperature settings depending on the care label instructions.

WARNING
Do not dry: · Fiberglass items (curtains, draperies, etc.) · Woolens, unless recommended on the label · Items spotted or soaked with vegetable or cooking oils

48 English
Untitled-3 48

2023-10-05 3:11:12

Special features
Child Lock Child Lock prevents children from playing with the dryer. When Child Lock is activated, all buttons except for the Power button are disabled. To activate/deactivate Child Lock, simultaneously press and hold Dryness and Temp. for 3 seconds.
NOTE Once Child Lock is activated, it will remain active even after you restart the dryer. If other buttons, except for the Power button, do not respond, check the Child Lock indicator. If the indicator is on, follow the instructions above to turn Child Lock off.
Sound Off You can turn on or off the sound from the dryer. Please note that this setting does not affect the sound that notifies information codes and Damp Alert. · To mute the sound, hold down Drum Light for 3 seconds. · To unmute the sound, hold down again for 3 seconds.
Smart Control To enable this function, you must first download the Samsung Smart Washer/Dryer app at the Play Store or the App Store and install it on a mobile device featuring a camera function. The Smart Control function has been optimized for Galaxy & iPhone series (applicable models only). 1. When the dryer detects an issue to check, an information code appears on the display. To enter Smart
Control mode, press and hold Wrinkle Prevent for 3 seconds. 2. The dryer starts the self-diagnosis procedure and displays an information code if a problem is detected. 3. Run the Samsung Smart Washer/Dryer app on your mobile device, and then tap Smart Control. 4. Put the mobile device close to the dryer’s display so that the smartphone camera and the dryer face
each other. The app automatically recognizes the information code. 5. When the information code is recognized correctly, the app provides detailed information about the
problem with applicable solutions.
NOTE · The function name, Smart Control, may differ depending on the language. · If light is reflected off the dryer’s display, the app may fail to recognize the information code. · If the app fails to recognize the information code, you can enter the code manually in the app.

Untitled-3 49

English49
2023-10-05 3:11:12

Operations
DOWNLOADED cycle You can choose from more cycles available on the SmartThings app on your smartphone. 1. On your smartphone, select the DOWNLOADED cycle.
You can choose from TOWELS, SANITIZE, SHIRTS, DENIM, WOOL, ECO NORMAL, LOW TEMP., RACK DRY, and WRINKLE AWAY. 2. Press Power on your dryer. 3. Turn the Cycle Selector to DOWNLOADED. 4. Press and hold Start/Pause (Hold to Start).

50 English
Untitled-3 50

2023-10-05 3:11:12

SmartThings
Wi-Fi connection On your smartphone, go to Settings, turn on the wireless connection, and then select your AP (Access Point). · This appliance supports the Wi-Fi 2.4 GHz protocols.
Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app using the search term “SmartThings”. Download and install the app on your device.
NOTE The app is subject to change without notice for improved performance.
Log in You must first log into SmartThings with your Samsung account. To create a new Samsung account, follow the instructions in the app. You don’t need a separate app to create your account.
NOTE If you have a Samsung account, use the account to log in. A registered Samsung smartphone user automatically logs in.
To register your appliance to SmartThings 1. Make sure your smartphone is connected to a wireless network. If not, go to Settings and turn on the
wireless connection, and then select your AP (Access Point). 2. Open SmartThings on your smartphone. 3. If the “A new device is found.” message appears, select Add. 4. If no message appears, select + and then select your appliance from the list of devices available. If
your appliance is not listed, select Device Type > Specific Device Model, and then add your appliance manually. 5. Register your appliance to the SmartThings app. a. Add your appliance to SmartThings. Make sure your appliance is connected to SmartThings. b. When registration is complete, then name of your appliance appears on your smartphone.

Untitled-3 51

English51
2023-10-05 3:11:12

Maintenance

Keep the dryer clean to prevent decreased performance and to lengthen its life.
WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the following parts while the appliance is energized: Control board and inlet valve.

Vent Sensor (DVE(G)55CG7500* models only)
The dryer features a vent sensor that detects and notifies you when it is time to clean the ductwork. The indicator lets you know the status of the duct.

Level 0 1
2

Indicator Off On
Blinking

Status

Action

The ductwork is not clogged.

· The duct or lint filter is clogged. · The pressure applied to the duct
is high because the duct is too long or bent.

· Check the lint filter or duct and clean if necessary.
· Check the duct connections and shorten or straighten the duct if necessary.

· The duct or lint filter is severely clogged.
· The pressure applied to the duct is very high because the duct is too long or bent.

· Check and clean the lint filter or duct and make sure they are not clogged.
· Check the duct connections and shorten or straighten the duct work.

If the dryer is in the Level 2 state, the indicator blinks for 3 hours after the completion of the current cycle. If you press Power or open the door, the dryer powers off immediately.
NOTE
· For duct installation, see “Exhaust ducting guide” on page 34 and “Ducting requirements” on page 18. · The dryer may keep running even if the duct is clogged, but the drying time will be extended. · If the indicator turns on for the first time and is solid (not blinking), check and clean the lint filter and/
or duct. · If the indicator turns on again later, it is because the duct is installed or connected with some
restrictions (it’s too long or has too many bends). This is not a system failure. However, drying time may be extended or the drying performance may be degraded.

52 English
Untitled-3 52

2023-10-05 3:11:12

Cleaning
Control panel · Clean with a soft, damp cloth. Do not use
abrasive substances. · Do not spray liquid cleaning agents directly
onto the dryer display. · Some laundry pre-treatment soil and stain
removers may damage the control panel. · When using liquid cleaning agents, apply
them to the cleaning cloth. Do not apply them directly to the dryer. Wipe up any spills or overspray immediately.
Drum · Remove any stains from the drum with an all-
purpose cleaner. · Tumble old towels or rags to remove any
remaining stains or cleaning substances. Stains may be still visible but will not affect subsequent loads.

Powder coated drum To clean the powder coated drum, use a damp cloth with a mild, non-abrasive cleaner suitable for easily marred surfaces. Remove cleaner residue and dry with a clean cloth.
Dryer exterior · Clean with a soft, damp cloth. Do not use
abrasive substances. · Protect the surface from sharp objects. · Do not place any heavy or sharp objects or
a detergent container on the dryer. They can scratch or damage the top cover of the dryer. · The dryer has a high-gloss finish on the entire surface. Be careful not to scratch or damage the surface.
Exhaust system · Check and clean the exhaust system
on a regular basis to maintain optimum performance. · The external exhaust hood must be cleaned frequently to ensure proper air flow.

Untitled-3 53

English53
2023-10-05 3:11:13

Troubleshooting

Checkpoints
If the dryer operates abnormally, first check the list of problems in the table below and try the suggested actions.

Problem Does not run. Does not heat.
Does not dry.

Action
· Make sure the door is latched shut. · Make sure the power cord is plugged into a live electrical outlet. · Check your home’s circuit breakers or fuses. · Press or tap Start/Pause (Hold to Start) again if the door is opened
during a cycle. · Clean the lint filter.
· Check your home’s circuit breakers or fuses. · Some cycles do not require heating. Check the selected cycle again. · For a gas dryer, make sure the gas supply is on. · Clean the lint filter and exhaust duct. · The dryer may have moved into the cool-down phase of the cycle. · Turn off the Eco Dry option for the NORMAL or TIME DRY cycles. When
the Eco Dry option is on, the dryer performs an air dry process in the beginning of the cycle to reduce energy consumption. The air dry process does not use heated air, so you may feel that the dryer is not being heated, but this is normal.
· Check all of the above, plus… · Make sure the exhaust hood outside your home can open and close
freely. · Check the exhaust system for lint buildup. Ducting should be
inspected and cleaned annually. · Use a 4″ rigid metal exhaust duct. · Do not overload. 1 wash load = 1 dryer load. · Dry heavy items and light weight items separately. · Large, bulky items, such as blankets or comforters, may require
repositioning to ensure even drying. · Make sure that your washer is draining properly and extracting
adequate water from the load. · The load may be too small to tumble properly. Add a few towels and
restart the dryer. · The load may be too large to tumble properly. Remove some items
and restart the dryer. · Clean the lint filter.

54 English
Untitled-3 54

2023-10-05 3:11:13

Problem Is noisy.
Dries unevenly.
Has odors.
Lint on clothes. Items still wrinkled after WRINKLE PREVENT (WRINKLE-CARE, WRINKLE RELEASE).

Action
· Check the load for objects such as coins, loose buttons, nails, etc. Remove promptly.
· It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle.
· Make sure the dryer is leveled properly as outlined in the installation instructions.
· It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum, fan, or exhaust system.
· Seams, pockets, and other similarly heavy areas may not be completely dry when the rest of the load has reached the selected dryness level. This is normal. You can choose a higher dryness level or a cycle that involves a higher dryness level.
· If one heavy item is dried with a light weight load, such as one towel with sheets, it is possible that the heavy item will not be completely dry when the rest of the load has reached the selected dryness level.
· For the best drying results, dry heavy items and light weight items separately.
· Household odors from paint, varnish, strong cleaners, etc. may enter the dryer with the surrounding room air. This is normal as the dryer draws the air from the room, heats it, pulls it through the tumbler, and exhausts it outside.
· When these odors linger in the air, completely ventilate the room before using the dryer.
· Use a cycle featuring the Refresh function. If odors persist, wash and dry the item again.
· Use the REFRESH cycle. If odors persist, wash and dry the items again.
· Make sure the lint filter is cleaned before every load. For clothes that naturally build up lint, clean the filter during the cycle.
· Some fabrics are lint producers (for example, a fuzzy white cotton towel) and they must be dried separately from clothes that are lint trappers (for example, a pair of black linen pants).
· Divide larger loads into smaller loads for drying. · Check pockets thoroughly before drying, then dry clothes. · Remove lint inside the drum before drying.
· Small loads of 1 to 4 items work best. · Load fewer items. Load similar-type items. · Take out the items immediately after drying is complete.

Untitled-3 55

English55
2023-10-05 3:11:13

Troubleshooting

Problem Water drips from the nozzle when STEAM CARE starts. Sprayed water is not visible during STEAM CARE.
Extended time.

Action · This is steam condensation. The dripping water will stop after a short
time.
· Sprayed water is difficult to see when the door is closed.
· Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level is reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference.

If a problem persists, contact a local Samsung service center.

56 English
Untitled-3 56

2023-10-05 3:11:13

Information codes
If the dryer fails to operate, you may see an information code on the display panel. To determine what you should do, check the list of codes in the table below, and then try the suggested actions.

Code dC FC AC HC
9C1
tC
tC5 dF 3C

Action
Operating the dryer with the door open. · Make sure the door is properly closed. · Make sure laundry is not caught in the door.
Invalid power source frequency. · Try restarting the cycle. · If this information code remains, contact a Samsung service center.
Electronic control problem (Invalid Communication). · Contact a Samsung service center.
High temperature heating check · Clean the lint filter. · If this information code remains, contact a Samsung service center. (enter the
line test mode)
The electronic control needs to be checked. · Check if power cord is connected properly. · Check if the electrical outlet is working properly. · If the information code remains, contact a Samsung service center.
The Thermistor1 resistance is very low or high. · Check for a clogged lint screen · Check if the vent system is restricted. · If this information code remains, contact a Samsung service center.
The Thermistor2 resistance is very low or high. · Check for a clogged lint screen. · Check if the vent system is restricted. · If this information code remains, contact a Samsung service center.
Incorrect door switch. · Contact a Samsung service center.
The PBA needs to be checked. · Unplug the power plug and contact a Samsung service center.

If any information code keeps appearing on the display, contact a Samsung service center.

Untitled-3 57

English57
2023-10-05 3:11:13

Specifications

Fabric care chart
The following symbols provide garment care direction. The clothing care labels include symbols for drying. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems. Tumble Dry Cycles
Dry Normal Permanent Press Delicate/Gentle Do Not Dry (Used with Do Not Wash) Do Not Tumble Dry In the Shade (Added to Line Dry, Drip Dry or Dry Flat) Line Dry/ Hang to Dry Drip Dry Dry Flat
Tumble Dry Heat Setting Any Heat High Medium Low No Heat/ Air

58 English
Untitled-3 58

2023-10-05 3:11:14

Protecting the environment
This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance.
Specification sheet

Type

Capacity (Cu.ft)

Water pressure (psi (kPa))

Weight

lb (kg)

Heater rating

Electric dryer (W) Gas dryer (BTU/hr)

Power consumption (W)

Front loading dryer 7.4
20-116 (137-800) 119.0 (54.0) 5300 20000 5400

Untitled-3 59

English59
2023-10-05 3:11:14

LIMITED WARRANTY

LIMITED WARRANTY (U.S.A.)

SAMSUNG DRYER
LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF PURCHASE AND/ OR PROOF OF DELIVERY
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials or workmanship for the following limited warranty periods, starting on the date of delivery to the original consumer purchaser:
One (1) Year All Parts and Labor
This limited warranty is valid only on products purchased and used in the United States that have been installed, operated, and maintained according to the instructions attached to or furnished with the product. To receive warranty service, the purchaser must contact SAMSUNG at the address or phone number provided below for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale and/or proof of delivery must be presented upon request to SAMSUNG or SAMSUNG’s authorized service center to receive warranty service.
SAMSUNG will provide in-home service within the contiguous United States during the warranty period at no charge, subject to availability of SAMSUNG authorized servicers within the customer’s geographic area. If in-home service is not available, SAMSUNG may elect, at its option, to provide transportation of the product to and from an authorized service center. If the product is located in an area where service by a SAMSUNG authorized servicer is not available, you may be responsible for a trip charge or required to bring the product to a SAMSUNG authorized service center for service.
To receive in-home service, product must be unobstructed and accessible to the service agent.
During the applicable warranty period, a product will be repaired, replaced, or the purchase price refunded, at the sole option of SAMSUNG. SAMSUNG may use new or reconditioned parts in repairing a product, or replace the product with a new or reconditioned product. Replacement parts and products are warranted for the remaining portion of the original product’s warranty or ninety (90) days, whichever is longer. All replaced parts and products are the property of SAMSUNG and you must return them to SAMSUNG.

60 English
Untitled-3 60

2023-10-05 3:11:14

This limited warranty covers manufacturing defects in materials or workmanship encountered in normal household, noncommercial use of this product and shall not cover the following: damage that occurs in shipment, delivery, installation, and uses for which this product was not intended; damage caused by unauthorized modification or alteration of the product; product where the original factory serial numbers have been removed, defaced, changed in any way, or cannot be readily determined; cosmetic damage including scratches, dents, chips, and other damage to the product’s finishes; damage caused by abuse, misuse, pest infestations, accident, fire, floods, or other acts of nature or God; damage caused by use of equipment, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG; damage caused by incorrect electrical line current, voltage, fluctuations and surges; damage caused by failure to operate and maintain the product according to instructions; in-home instruction on how to use your product; and service to correct installation not in accordance with electrical or plumbing codes or correction of household electrical or plumbing (i.e., house wiring, fuses, or water inlet hoses). The cost of repair or replacement under these excluded circumstances shall be the customer’s responsibility.
Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues.
EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights, and you may also have other rights, which vary from state to state.

Untitled-3 61

English61
2023-10-05 3:11:14

LIMITED WARRANTY (U.S.A.)
LIMITATION OF REMEDIES YOUR SOLE AND EXCLUSIVE REMEDY IS PRODUCT REPAIR, PRODUCT REPLACEMENT, OR REFUND OF THE PURCHASE PRICE AT SAMSUNG’S OPTION, AS PROVIDED IN THIS LIMITED WARRANTY. SAMSUNG SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TIME AWAY FROM WORK, HOTELS AND/OR RESTAURANT MEALS, REMODELING EXPENSES, LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights, and you may also have other rights, which vary from state to state.
SAMSUNG does not warrant uninterrupted or error-free operation of the product. No warranty or guarantee given by any other person, firm, or corporation with respect to this product shall be binding on SAMSUNG.
To obtain warranty service, please contact SAMSUNG at: Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660 1-800-SAMSUNG (726-7864) www.samsung.com/us/support

62 English
Untitled-3 62

2023-10-05 3:11:14

Warranty (CANADA)
SAMSUNG DRYER
LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of: · One (1) year part and labor
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the Canada.
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability within the Canada. In- home service is not available in all areas.
To receive in-home service, product must be unobstructed and accessible to the service agent. If service is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized service center. SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following: damage that occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal and reinstallation; problems caused by pest infestations. This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply, light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
English63

Untitled-3 63

2023-10-05 3:11:14

Warranty (CANADA)
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE.
WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE, OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights, and you may also have other rights, which vary from province to province.
To obtain warranty service, please contact SAMSUNG at: Samsung Electronics Canada Inc. 2050 Derry Road West, Mississauga, Ontario L5N 0B9 Canada 1-800-SAMSUNG (726-7864) www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French)
Visits by a Service Engineer to explain functions, maintenance, or installation is not covered by warranty. Please contact the Samsung call center at the number above for help with any of these issues.

64 English
Untitled-3 64

2023-10-05 3:11:14

Memo

Untitled-3 65

2023-10-05 3:11:14

Memo

Untitled-3 66

2023-10-05 3:11:14

Memo

Untitled-3 67

2023-10-05 3:11:14

Scan this with your smartphone
Energy Star only applies to DVE(G)55CG7500* model. This product qualifies for ENERGY STAR in the factory default “NORMAL + Eco Dry” setting. If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR.

QUESTIONS OR COMMENTS?

COUNTRY U.S.A

CALL 1-800-SAMSUNG (726-7864)

CANADA

1-800-SAMSUNG(726-7864)

OR VISIT US ONLINE AT www.samsung.com/us/support www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French)

Untitled-3 68

2023-10-05 3:11:14

References

• Samsung Open Source
• Samsung US | Mobile | TV | Home Electronics | Home Appliances | Samsung US
• P65Warnings.ca.gov
• Aide et assistance : produits | Samsung Canada
• Product Help & Support | Samsung CA
• Support Home | Official Samsung Support US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>