FelixKing FK-18-HT Ergonomic Office Chair Instruction Manual

: May 15, 2024
: FelixKing

Table of Contents

FK-18-HT Ergonomic Office Chair
Accessories List
Instructions for Use
Assembly Instruction
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FK-18-HI
Assembly Instruction

FK-18-HT Ergonomic Office Chair

FelixKing FK 18 HT Ergonomic Office Chair - QR Code https://aftersale.qingtong123.com/landingpage/index.html?landing_page_id=109 FelixKing
FK 18 HT Ergonomic Office Chair - QR Code 1 https://aftersale.qingtong123.com/landingpage/index.html?landing_page_id=109

installation video

Accessories List

FelixKing FK 18 HT Ergonomic Office Chair -
Accessories Notice [if any question, contact Felixking-serive@outlook.com / Felixking-Spt@outlook.com]

One chair can only bear one person’s weight.
Please use on the flat floor.
Please don’t let the child sit on the chair alone if he Is under 5 year-old.
Please don’t sit on the armrest, in case cause some danger.
Do not stand on the chair or use it as a ladder or footsteps.
Please don’t put overweight on the chair, or used as trolley.
Don’t use sharp or hooked objects to scrape the chair and do not get it close to the fire.
To avoid any harm to your fingers, don’t insert them into the mechanism while sitting.

Instructions for Use

FelixKing FK 18 HT Ergonomic Office Chair -
Instruction Thanks for purchasing our products. Please read this manual before assembly.
And please assemble in order. After the assembly, keep the instruction properly.
Make sure all the parts are included (26 kinds in total).

Assembly Instruction

Please assemble in a wide and flat place. Extend the Foot Stool(6). Take out Castors(8). Insert Castors (8)into Foot Stool(6). There are 5 Castors(8) need to be inserted.

Caution: Confirm Castors(8) must be inserted deeply Otherwise, the casters could easily fall out and the chair could fall down. First, take out Gas Lift(7). Put Gas lift(7) into the hole of Foot Stool(6) as shown.
Second, take out the Headrest(1)and install 2 Screws
M6x14mm(23), 2 Plastic Caps(24), and 2 Gaskets(25)on
Headrest Bracket(26) as shown in the figure. Then combine it with the Headrest(1). Set them aside, we will use them in step 8. Take out the Seat Cushion(3). Take the Armrest(4)under the Seat Cushion(3)as shown in the picture. Three screw holes can be seen. Align the holes, and tighten the Screws M6X30(15), the Screws M6X35(16)and Flat Gasket M6X16X2mm(22)with an 5mm Hexagon Wrench(11). Take Base Plate(5). Put Base Plate(5)on the bottom of Seat Cushion(3)as shown. You can see there are four screw holes.
Align with the holes, tighten Screws M6X25mm(14), Flat Gaskets M6X10X2mm(21), Flat Gaskets M6X16X2mm(22), with 5mm Hexagon Wrench(11)to fix Base Plate(5) to the bottom of Seat Cushion(3).
*Note: There is a FRONT sticker on the front of the Seat Cushion(3). Take Corner Connector(10). Put Corner Connector(10)on the bottom of Base Plate(5)as shown. You can see there are three screw holes. Align with the holes, tighten Screws M8X20mm(18), Flat Gaskets M8X13X2mm(19), Flat Gaskets M8X20X2mm(20), with 5mm Hexagon Wrench(11)to fix Corner Connector(10)to the Base Plate(5). Take Backrest(2). Put Corner Connector(10) on the Backrest(2) as shown. You can see there are four screw holes. Align with the holes, tighten Screws M8X25mm(17), Flat Gaskets M8X13X2mm(19), Flat Gaskets M8X20X2mm (20), with 5mm Hexagon Wrench(11)to fix Backrest(2)to the Corner Connector(10). Take Decorative Cover L1(9). Put Decorative Cover L1(9)on the Base Plate(5)as shown. You can see there are two screw holes. Align with the holes, tighten Screws M6X16mm(13) with 4mm Hexagon Wrench(12)to fix Decorative Cover L1 (9)to the Base Plate(5).
Take Decorative Cover L2(9). Fasten it to the Backrest(2) without screws. Take out completed part of previous Step. You can see a hole in the middle of the Base Plate (5). Insert it into the section from step 2 as shown in the picture. At this point, you should press the seat cushions with all your strength to make sure they fit each other better.
Then align the Headrest(1)installed in step 2 with the screw hole at the top of the Backrest(2) and tighten the Screws M6X16mm (13) with a 4mm Hexagon Wrench(12).
Caution: If the Gas Lift (7) doesn’t insert to Base Plate (5) firmly, it’s likely to fall off when the chair raises up.

Activate Your Warranty Now!
FelixKing guarantees you a pleasant buying experience. Please scan the QR code to activate your warranty, so that you can enjoy priority and better after- sales service.

FelixKing FK 18 HT Ergonomic Office Chair - QR Code 2 https://aftersale.qingtong123.com/landingpage/index.html?landing_page_id=109