FelixKing FK968ZK Ergonomic Desk Chair Instruction Manual

FelixKing FK968ZK Ergonomic Desk Chair

Accessories List

Notice If any question, contact FelixKing-service@outlook.com / FelixKing-Spt@outlook.com]

• This is a single chair, so please do not seat 2 or more persons, just seat only one person.
• Do not stand on the chair.
• Do not sit reverse or sit outside of the seat cushion.
• Check the screws once every 6 months, to make sure the screws are tight. Do not use the chair when the screws are loose.
• Please assemble according to the instructions

Instructions for Use

Thanks for purchasing our products. Please read this manual before assembly. And please assemble in order. After the assembly, keep the instruction properly. Make sure all the parts are included (18 kinds in total).

Assembly Instruction

Please assemble in a wide and flat place.

1. Take out Split Base Tube (4) and Central Base Tube (5). Insert Split Base Tube (4) into Central Base Tube (5) as shown. You can see there are two screw holes. Align with the holes, tighten Screws M6X12mm (17) with Allen Driver (18) to fix 5 Split Base Tube (4) to Central Base Tube (5). Repeat five times.

2. Take out Castors (9). Insert Castors (9) into part of Step 1 as shown. There are 5 Castors (9) need to be inserted.
   Caution: Confirm Castors (9) must be insert­ed deeply. Otherwise the castors could easily fall out and the chair could fall down

3. Take out Gas Lift (10). Insert Gas Lift (10) into the hole of Central Base Tube (5) as shown. Put it aside and we’ll use it in Step 8.

4. Take out Seat Cushion (3). Put Armrests (6) under Seat Cushion (3) as shown. You can see there are three screw holes. Align with the holes, tighten Screws M6X30mm (16) with Allen Driver (18) to fix 2 Armrests (6) to the bottom of Seat Cushion (3).
   Caution : There is a FRONT sticker on the front of Seat Cushion (3).

5. Take out Mechanism (7). Put Mechanism (7) on the bottom of Seat Cushion (3) as shown. You can see there are four screw holes. Align with the holes, tighten Screws M6X20mm (14) with Allen Driver (18) to fix Mechanism (7) to the bottom of Seat Cushion (3).
   

6. Tighten the Screws M6X30mm (16) with Allen Driver (18) to fix 2 Armrests (6) to the bottom of Seat Cushion (3).Tighten the Screws M8X25mm (15), Spring Shim (13) and Flat Gasket (12) with Allen Driver (18) to fix Keel (8) to Mechanism (7). * Caution: There is a FRONT sticker on the front of Seat Cushion (3).
   

7. Take out Back (2). You can see there are three screw holes as shown. Align with the holes, tighten Screws M6X20mm (14) with Allen Driver (18) to fix Back (2) to Keel (8) and then cover the screws with L2 (11 ). In the same way, tighten the Screws M6X20mm (14) with Allen Driver (18) to fix Headrest (1) to Back (2) and then cover the screws with L 1 (11).

8. Take out completed part of previous Step. You can see there is a hole in the middle of Mecha­nism (7). Insert it into part of Step 2 as shown. At this time, you should use your whole strength to press the seat cushion hardly to make sure they combine with each other better.

9. Caution : If the Gas Lift (10) doesn’t insert to Mechanism (7) firmly, it’s likely to fall down when the chair raises up.

Activate Your Warranty Now!
FelixKing guarantees you a pleasant buying experience. Please scan the QR code to activate your warranty, so that you can enjoy priority and better after-sales service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>