VEVOR TS-103 Handheld Metal Detector User Manual
- May 15, 2024
- VEVOR
Table of Contents
VEVOR TS-103 Handheld Metal Detector
We continue to be committed to providing you tools with at competitive prices. “Save Half”, “Half Price” or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to other brands and do not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are saving half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us: Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
Warning
To reduce the risk of injury, users must read the instructions manual
carefully. This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions
This device may not cause harmful interference, and (2)this device must accept
any interference received, including interference that may cause undesired
operation.
This product is subject to the provision of EuropeanDirective2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste but must be taken to a collection point for recycling electrical and electronic devices.
FEATURES
- Detect metal objects in all directions.
- High-precision identifying system.
- Auto power off.
- Low power consumption.
- Shock resistance.
- Small size, lightweight.
- Waterproof design, IP degree of IP68.
SPECIFICATIONS
- Sensitivity: 40mm ( for one dollar coin )
- Alarm Mode:
- Mode 1: Vibration and buzzer sound alarm mode
- Mode 2: Buzzer sound alarmmode
- Mode 3: Vibration alarm mode
STRUCTURE
INSTALLING BATTERY
- Remove the battery cover by turning it counterclockwise.
- Install a new 9V battery ( 6F22 or equivalent ) in the battery compartment, and make sure the polarity connections are correct (see Figure 2 ); the metal detector may be damaged.
- Reinstall the battery cover, and turn it clockwise to secure the place
OPERATION INSTRUCTION
-
Hold the detector by the handle. Make sure that the detector is far away from any metal object, and then press the power of the detector.
-
The green power indicator LED and the illumination lamp light up, and the detector vibrates once and/or the buzzer sounds a beep, indicating that the detector has been turned on.
-
The detector starts calibration automatically. The calibration takes about 2 to 4 secs. When the calibration is completed, the detector vibrates briefly two times and/or the buzzer sounds two beeps.
Note: lf you want to use this detector to detect metal objects buried in mineralised soil, salt water or wet salt sand, you must hold the tip of the detector to mineralized soil! saltwater or wet salt sand and turn on the detector to let it perform auto calibration there. -
Move the detecting wand smoothly along thesurface of the object to be checked. As the detector gets close to a metal object, it will start to vibrate and/or the built-in buzzer will sound.
-
The vibration and/or the beep sound will intensify as the detector gets closer to the metal.
-
After the detector is turned on and calibrated, you can press and hold the power button for about 2 seconds to enter the alarm-mode-switching state.
-
The illumination light will flash as an indication
-
The detectors or default to enter the alarm mode with vibration and buzzer sound.
-
Press the power button once to switch to the buzzer sound alarm mode. and press it again to switch to the vibration alarm mode.
-
After selecting the desired mode, press and hold the power button for about 2 seconds, or wait for about 5 seconds for the detector to automatically confirm.
Note: After the next power-up, the detector will default to the one confirmed in the previous use. -
After finishing using the detector, press the power button once to turn off the detector; the detector will vibrate three times and/or the sound will beep
Note: -
Before each use, verify the detector’s operation by detecting a known metal object.
-
Do not use the detector if it operates abnormally.
- If the display shows the symbol ” “, the battery is not high enough and you must replace the battery immediately; otherwise, the detector may not operate or detect metal normally.
- When the battery is too low, the detector will turn off automatically.
- When the battery is too low, the detector will turn off automatically.
- To save battery charge, turn off the detector when not in use.
AUTOMATIC POWER OFF
lf you have not pressed the power button and the detector has not detected any
metal object for about 5 minutes, the detector will start to prompt with
vibration and/or buzzer sound every 12 secs. After six prompts, the detector
will turn off automatically. Note: If any metal object is detected or the
power button is pressed, the prompt will be cancelled andthe timer will reset.
DECLARATION
- This Instruction Sheet is subject to change without notice.
- Our company will not take the other responsibilities for any loss.
- The contents of this Instruction Sheet can not be used without the detector for any special application.
LIST OF ACCESSORIES
- 9V carbon tandem battery (6F22)*1
- Waist hanging cover*1
- Telescopic lanyard*1
- Instructions*1
DISPOSAL OF THIS ARTICLE
Dear Customer,
lf you at some point intend to dispose of this article, then please keep in
mind that many of its components consist of valuable materials which can be
recycled. Please do not discharge it in the garbage bin, but check with your
local council for recycling facilities in your area. Address: Baoshanqu
Shuangchenglu 803long 11hao 1602A-1609shi ShanghaiImported to AUS: SIHAO PTY
LTD.ROKEVA STREETEASTWOODNSW2122Australia Imported to the USA: Sanven
Technology Ltd. Suite 250, 9166 AnaheimPlace, Rancho Cucamonga, CA 91730
SHUNSHUN GmbH
Römeräcken 9 22021, 76351
inkenheim-Hochstetten, Germany
Pooledas Group Ltd
Unit 5 Albert Edward House, The
Pavilions Preston, United Kingdom
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>