wimo BCD 6-2 MK2 Antenna Switch 6-to-2 MK2 Classic Instruction Manual
- March 7, 2024
- WiMo
Table of Contents
wimo BCD 6-2 MK2 Antenna Switch 6-to-2 MK2 Classic Instruction Manual
This 6-to-2 (six-2-two) RF switch designed for SCR operations. Version MK2 have got higher colletion and new hazard protecton board. There is still Fint- Win switching and added BCD inputs Unused ANT ports are connected to ground. Switch can handle more than 3 kW of the RF power. Do not forget to Hat Switch Protection
Jump to
Applications
Switch ControlConnection
BCD control examples
Parameters
Product details
Applications
- SO2R antenna switch (2 TRX to 6 ANT)
- BPF switch for 2 TRX
- 6 TRX to 2 antennas
version with PL SO-239 connectors
version with N connectors
Example for 2 TRX and 6 antennas
Example for Band Pass Filters switching for 2 TRX
6-to-2 RF SWITCH BPF switching example
Switch Control – Connection
- It is possible to use connectors A – IN 1-6, B – IN 1-6 for conventional control over 2×6 wires (+ GND). The switch is controlled by + DC voltage > 12 V
- You can also use the BCD inputs A – BCD IN and B – BCD IN
- The switch uses binary combinations for 1 to 6. Again + DC voltage
- The BCD control has a voltage range from 3 V to 15 V. It is therefore compatible with TTL logic
- If you use TTL logic, it is necessary to connect also voltage for relay control – terminal +12 at BCD. The recommended voltage is 13.8 V. It is possible to supply this voltage separately for the A and B part. If the jumper (+12V A/B | AB) is switched to the A/B position, each half of the switch needs its own voltage (+12V at BCD). In this case, the part not in use may be without power. In the AB position, only one power supply to one of the +12 at the BCD connector is needed.
- If the BCD control voltage is higher than +13 V (13 to 15 V DC), you can use only the BCD + GND wires. The voltage for the relay is derived from the BCD control voltage.
Control connectors
BCD control examples
The control voltage can range from 3 to 15 V. In case it is lower than 12 V, the power supply for relay control (+12 V) must be connected. You need 5 wires for one TRX. If the BCD voltage is higher than 13 V, no additional voltage needs to be connected. 4 wires are needed (for each TRX). If you are using a long control cable, you can use the > 12 V control BCD voltage and also connect > 12 V to the +12 V connector.
When you use device with Open Collector:
- You have to add Pull Up resistors 4k7, 0.25 W from + 12 V DC (12-15 V)
- Or smaller 1k when you use + 5 V for Pull Ups
Parameters
A – 1 VSWR
B – 4 VSWR
B – 6 VSWR
A – B no selected
A – 2, B – 1
A – 4, B – 1
Product details
Included in package
Switch assembled and tested
Mounting holder with bracket – image
Box dimensions (mm) | 222x145x75 – al box IP65 |
---|---|
Weight brutto (kg) | 2.75 kg |
Manufacturer:
Ing. Jan Šustr
ID 05476356, VAT CZ8407024780
Palachova 1777/7, 591 01 Czech republic, Europe
General instructions:
Please also read general instructions before handling the product
European Union Declaration of Conformity
Manufacturer Ing. Jan Šustr (QRO.cz):
ID 05476356, VAT CZ8407024780
Palachova 1777/7, 591 01 Žďár nad Sázavou, Czech republic, Europe
declares that the assembled product
6-2 SWITCH MK2 CLASSIC
is compatible with the relevant Union harmonisation legislation directives:
EMC Directive 2014/30/EU ČSN EN 61000-6-3 ed. 2 ČSN EN 61000-6-1 ed. 2
(333432)
On behalf of Ing. Jan Šustr (QRO.cz)
Ing. Jan Šustr, CEO
1st January 2023
Tag: manual, switch, antenna switch, 6-2, 6 to 2, classic
Previous article
RELATED PRODUCTS
Easy Controller manual
Easy controller manual
Antenna switch 6-to-1 manual
Easy Controller 5-2
6-to-2 antenna switch MIG CLASSIC
6-to-1 antenna switch
LEAVE A COMMENT
agree to the Terms and Conditions and the Privacy Policy
Post comment
2021-2023 hamparts shop All Rights Reserved. Designed by Lucine Terms and
Conditions Privacy Policy Cookies EU COCOR platform Cookies settings
References
- QRO.cz | not only amateur radio projects
- hamparts.shop
- 6-to-1 antenna switch ASSEMBLED version | hamparts.shop
- 6-to-2 antenna switch classic MK2 ASSEMBLED version | hamparts.shop
- Blog | hamparts.shop
- manual 4-way switch by qro.cz | hamparts.shop
- manual 6-2 easy controller by qro.cz | hamparts.shop
- manual 6-to-1 antenna switch by qro.cz | hamparts.shop
- manual 6-to-2 antenna switch MK2 classic version by qro.cz | hamparts.shop
- manual bias tee box AC/DC by qro.cz | hamparts.shop
- manual easy controller by qro.cz | hamparts.shop
- technical article holder by qro.cz | hamparts.shop
- Blog | hamparts.shop
- Blog | hamparts.shop
- Blog | hamparts.shop
- Blog | hamparts.shop
- Blog | hamparts.shop
- Blog | hamparts.shop
- Wiki - manuals
- Contact us
- ADR/ODR platform
- Cookies information
- FAQs - your frequently asked questions | hamparts.shop
- General instructions for qro.cz brand products | hamparts.shop
- All the information you need to know
- About Jan OK2ZAW and history of QRO.cz brand
- Privacy policy
- Terms and conditions
- Track & Trace - Find out where is your order right now
- Easy controller 6-2 | hamparts.shop
- hamparts.shop/img/cms/6-2/classic/6-2_bcd.jpg
- hamparts.shop/img/cms/6-2/classic/6-2_bpf.jpg
- hamparts.shop/img/cms/6-2/classic/6-2_classic.jpg
- hamparts.shop/img/cms/6-2/classic/6-2_mk2_control.jpg
- 6-2_N_classic_3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>