ROOQ RQ1 IoT Sensor User Manual
- June 5, 2024
- ROOQ
Table of Contents
ROOQ RQ1 IoT Sensor User Manual
Product Description
-
Ultra-Low-Power: 1.71 V to 3.6 V
power supply; 13 nA
shutdown mode; 600 nA Standby mode + RTC + 32 KB RAM;
Radio: Rx 4.5 mA / Tx at 0 dBm 5.2 Ma. -
Supports Bluetooth Low Energy and 2.4 GHz proprietary/custom protocols RX Sensitivity: -96 dBm (Bluetooth® Low Energy at 1 Mbps), -100 dBm (802.15.4)
-
Equipped with the latest Bluetooth 5.0 chip, the transmission data is further improved, and the connection is faster and more stable.
-
Use more accurate 3-axis accelerometer and 3-axis gyroscope to make punch recording more accurate.
-
Compact body, built-in large-capacity battery, with large-capacity MCS, longer battery life.
-
Different status of the sensor corresponds to different status light display, which is more intuitive.
MCS has a more accurate battery display, so you know it well. -
Restricts Bluetooth access to trustworthy users who presents a real digital identity.
-
Provide complete quality assurance, after-sales service and technical support.
Product Specification
Processor specification
| CPU | Arm®-based Cortex®-M4 |
|---|---|
| CPU Frequency | 64MHz |
| Internal Storage | 64Mbyte of flash memory |
| OS | Support FreeRTOS |
| Connective | BT5.0 |
| OTA | Suports |
Multi-Sensor
3-axis accelerometer
| Range: 0-10000g
---|---
3-axis gyroscope|
Sensitivity : 16.4 LSB/(deg/s)
Basic parameters
| Single Sensor Net Weight | ~10 g |
|---|---|
| Total weight with MCS | ~75 g |
| Sensor battery life | ~10 h |
| Including MCS battery life | ~25 h |
| Single Sensor battery capacity | 100mAh Li-on |
| MCS battery capacity | 1000mAh Li-on |
| Sensor size | 31.9mm8.9mm42.0mm |
| MCS size | 74.9mm35.5mm54.6mm |
| Sensor charging time | ~1.5 h |
| MCS charging time | ~1.5 h |
Power consumption
| Single Sensor sleep mode | ~7.5mA |
|---|---|
| Single Sensor working mode | ~9mA |
| MCS working mode | ~150mA |
Sensor signal test
- Install BLE debugging assistant (base.apk)
- Filter settings
Purpose: Screen out ROOQ sensors to be tested ：
-
Click the filter button
-
Set the filter name to ROOQ and RSSI to ‐45db
-
After the setting is completed, refresh, the scanned ROOQ sensoris within 10cm of the mobile phone.
FCC STATEMENT
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Importer :
Geniatech Europe GmbH
Address: Kaiserstrasse 100 (TPH 3) 52134 Herzogenrath, Aachen, Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>