WiMo UB-20MX EHU Tube Modification Kit Instruction Manual

June 1, 2024
WiMo

WiMo UB-20MX EHU Tube Modification Kit

WiMo-UB-20MX-EHU-Tube-Modification-Kit-product

Product Information

Specifications

  • Product Name: EHU Guide Tube Modification
  • Part Number: 12255.TubeModi
  • Compatibility: For combining older antenna models with new EHU
  • Kit Contents: Connection components for new EHU and older internal guide tubes

Product Usage Instructions

Installation Process

  1. Preparation: Degrease the tube ends with thinner or spirit, and avoid touching the bonding area.
  2. Assembly: Join the parts of the internal guide tube and secure the connection with an electrician’s plug. Fix with insulating tape.
  3. Connecting Tubes: Push the guide tube into the GRP tube, ensuring a secure fit. Use the provided black cone and sleeve for alignment.
  4. Final Steps: Secure the GRP tube with clamps to complete the installation.

Version for Cut Tube

  • If you have cut off the extended end of the internal guide tube, use the connecting piece supplied.
  • Follow the same installation steps as above, ensuring joints are fixed with insulating tape.

FAQ

  • Q: What should I do if I accidentally touch the bonding area during assembly?
  • A: If you touch the bonding area, clean it with thinner or spirit before proceeding with assembly to ensure a secure connection.
  • Q: Can I use this modification kit with any antenna model?
  • A: The kit is specifically designed to work with UltraBeam models that have internal guide tubes. Ensure compatibility before installation.

Introductions

  • If you want to combine an older antenna model with a new EHU, you need the EHU Guide Tube Modification Kit supplied by us.
  • The kit provides a connection between the new EHU and the older internal guide tubes.
  • This short manual explains how to correctly install the EHU Guide Tube Modification Kit.

WiMo-UB-20MX-EHU-Tube-Modification-Kit-fig-1

Models with internal guide tubes

  • All UltraBeam models with folded elements have internal guide tubes on the left and right elements that are connected to the motor unit.

WiMo-UB-20MX-EHU-Tube-Modification-Kit-fig-2

  • All motor units of the vertical loop elements require the installation of internal guide tubes in the upper elements connected to the motor unit.

WiMo-UB-20MX-EHU-Tube-Modification-Kit-fig-3

Construction of the internal guide tubes

WiMo-UB-20MX-EHU-Tube-Modification-Kit-fig-4

Assembly

  • “You can’t stick on dirt”: Degrease the ends of the tubes with thinner, spirit or similar and then avoid touching the bonding area.

  • Join the parts of the internal guide tube and secure the connection with commercially available electrician insulating tape (not supplied, Figs. 1 – 3). The adhesive layer of the insulating tape should ‘smear’ as little as possible and also be as heat-resistant as possible so that it does not dissolve later in the sun.

  • Push the guide tube completely into the GRP tube up to the outer edge of the black cone (Figs. 4 – 6).

  • Insert the GRP tube with the black cone first into the GRP part of the EHU as far as it will go (Figs. 7 + 8).
    Important: The outer edge of the black cone must be firmly clamped between the edge of the GRP tube and the stop inside the EHU!!

  • Fix the GRP tube to the EHU using the sleeve and the two clamps as shown in Fig. 9.

WiMo-UB-20MX-EHU-Tube-Modification-Kit-fig-5

Version for cut tube

  • In case you have cut off the extended end of the internal guide tube, we have supplied a connecting piece. This is fitted between the two internal tubes as shown in the illustration.
  • The joints are also fixed here with insulating tape (Figs. 12). The installation of the GRP tube with the internal guide tube is the same as in Figure 4 – 9.

WiMo-UB-20MX-EHU-Tube-Modification-Kit-fig-6

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals