Color IMAGINATION SI-119 FLYEYE 1920F LED Head User Manual

: June 4, 2024
: Color IMAGINATION

Table of Contents

SAFETY INSTRUCTIONS
UNPACKING
FEATURES & SPECIFICATIONS
- Features
- Specifications
PHOTOMETRIC DATA
- PHOTOMETRIC BEAM ANGLE DATA
OPERATION INSTRUCTIONS
INSTALLATIONS
DMX-512 CONTROL CONNECTIONS
MENU OPERATIONS
DMX CHANNELS
MAINTENANCE AND CLEANING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Color IMAGINATION SI-119 FLYEYE 1920F LED Head

SAFETY INSTRUCTIONS

| CAUTION
Becareful with your operations.With a dangerous voltage you cansuffer a dangerous electric shock when touching wires!
---|---

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.

| IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
---|---

If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

UNPACKING

Thank you for choosing our FLYEYE 1920F . For your own safety, please read this manual before installing the device. This manual covers the important information on installation and applications. Please install and operate the fixture with following instructions. Meanwhile, please keep this manual well for future needs.
The FLYEYE 1920F is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theater, studio, nightclubs and discos.

The FLYEYE 1920F adopts 19*15W OSRAM OSTAR 4-IN-1 RGBW LEDs which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation. And please check whether the following items are included inside the box:

FEATURES & SPECIFICATIONS

Features

19*20W OSRAM OSTAR 4-IN-1 RGBW LEDs
50000 hours life span and low power consumption
Each color and each LED controllable individually
8/16 bit smooth and precise resolution for PAN/TILT movement
Scan position memory, auto reposition after unexpected movement
Specific high precision optic lens
Variable direction rotating front lens
4°-60°Smooth electronic linear zoom
Brilliant hard beam effects at 4°
Pure and even wash coverage effects at 60°
Sophisticated 4 colors RGBW mixing texture
Petal-like micro beam effects
Pixel patterning macro effects
Built-in running programs
Built-in color and graphic effect macros
0-100% linear LED dimmer
1-25T/sec high speed LED shutter/strobe effect with variable speed
Preset variable/random strobe and dimming pulse effect
Art-Net,King-Net,DMX
21/35/78/92/97 DMX channels USITT DMX-512
DMX512, master-slave, and sound activated controllable or auto operation
DMX recorder and edit function integrated
High resolution graphic LCD display
POWER CON connector IN/OUT
3-pin XLR connectors IN/OUT
Aluminium structure with die-cast plastic cover
Two side handles for transportation
PAN lock for transport and maintenance
High efficiency low noise cooling system
Constant temperature readout and management function
45°C max ambient temperature
IP20 protection rating
55dB at 3’dB rating
2*1/4 turn fastening Omega clamp
1*Safety attachment point

Specifications

Input Voltage:	AC90-260V 50/60Hz
LED Quantities:	19*20W OSRAM OSTAR 4-IN-1 RGBW LEDs
Control Signal:	DMX512, master-slave and sound activated or auto operation
Comtrol protocols:	Ar t-Net,King-Net,DMX
Control Channel	21/35/78/92/97 DMX channels USITT DMX-512
Power Consumption:	480W
Dimensions:	253(D)358(W)494(H)mm
Packing Dimensions	333(D)438(W)564(H)mm
Net Weight:	15kg
Gross Weight:	17kg

PHOTOMETRIC DATA

PHOTOMETRIC BEAM ANGLE DATA

(FC=LUX × 0.0929)

OPERATION INSTRUCTIONS

The FLYEYE 1920F is for beam effect for on-site decoration purpose.
Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
This light should be keep away from strong shaking during any transportation or movement.
Don’t pull up the light by only the head, or it might cause damages to themechanical parts.
Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
Make sure the installation place is in good safety condition before installing the fixture.
Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture.
Make sure the lens are in good condition. It’s recommended to replace the units if there are any damages or severe scratch.
Make sure the fixture is operated by qualified personnel who knows the fixture before using.
Keep the original packages if any second shipment is needed.
Don’t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies.
It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.

INSTALLATIONS

Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails.

Mounting points: Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the
fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.

Clamp Mounting: FLYEYE 1920F provides a unique mounting bracket assembly that integrates the bottom of the base, and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the “omega bracket”. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly.

Regardless of the rigging option you choose for your , always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.

DMX-512 CONTROL CONNECTIONS

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving head together through serial linking. The cable needed should be two core, screened cable with XLR input and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below.

MENU| Address| (001~512)| |
---|---|---|---|---
Intro| Reset| NO|
YES|
Run| DMX512|
Artnet|
Auto1|
Auto2|
Sound 1|
Sound 2|
Slave|
Users m ode| Standard| |
Shapes| |
Extended| |
Extended r gbw| |
Full| |
Test| All| |
Pan&Tilt| |
LED| |
Set| Fan c ontro| Auto|
High|
Low|
Disp.setting| Shut oﬀ time| 02-60m
Flip d isplay| ON/OFF
Key lock| ON/OFF
Disp ﬂash| ON/OFF
Pan| Normal|
Reverse|
Tilt| Normal|
Reverse|
Info| Time Info| Power o n| xxx(House)
Ttl Life H rs| xxx(House)
Last R un Hrs| xxx(House)
Temp I nfo| Head Temp|
Software Ve r| Vxx|

11

|

11

|

11

|

11

|

11

|

Strobe

| 0-3| Colsed
4| Slow strobe(1ﬂash/sec)
5-103| Fast strobe(25 ﬂash/sec)
104-107| Open
108| Slow pulsation (0,5 ﬂash/sec)
109-207| Fast pilsation (25 ﬂash/sec)
208-212| Open
213-225| Random slow strobe
| | | | | | 226-238| Random medium strobe
239-251| Random fast strobe
252-255| Open
12| 12| 12| 12| 12| Dimmer| 0-255| 0-100% Linear dimmer
13| 13| 13| 13| 13| Dimmer Fine| 0-255| Fine control of dimmer
14| 14| 14| 14| 14| PAN| 0-255| 0~540° PAN movement
15| 15| 15| 15| 15| PAN Fine| 0-255| Fine control of PAN
16| 16| 16| 16| 16| TILT| 0-255| 0~230° TILT movement
17| 17| 17| 17| 17| TILT Fine| 0-255| Fine control of TILT
18| 18| 18| 18| 18| No Function| |
19| 19| 19| 19| 19| Reset| 0-25| No Function
26| Zoom reset
27-76| Zoom reset
77| Pan/Tilt reset
78-127| Pan/Tilt reset
128| Complete reset
129-255| Complete reset
20| 20| 20| 20| 20| Zoom| 0-255| 0-100% Linear zoom

21

|

21

|

21

|

21

|

21

|

Zoom Rotation

| 0-127| Linear roation
128-190| Slow rotation
191-192| Stop
193-255| Slow rotation
/| 22| /| /| 22| Shape Selection| 0-7| Macro OFF
8| Ring 1
9| Ring 2
10| Ring 3
11| No function
12| Ring 1+2
13| Ring 1+3
14| No function
15| Ring opening (closing)
16| Ring opening (closing)ﬁlled
17| Ring opening (closing/open)
18| Ring opening (closing/open)ﬁlled
19| Random pixels distributed on many ﬁxtures
20| Random pixels with varisble density and speed
21| Rainbow 1 Varisble speed
22| Rainbow 2 ﬁxed speed with variable color oﬀset
23| Fan (3 ams)
24| Bar (2 ams)
25| Half moon
26| Triangle
27| Two rotating bars of diﬀerent colors
| | | | | | 28| Two rotating arcs of diﬀerent colors
29| Two rotating arcs of diﬀerent colors and direction
30-255| Reserved
/| 23| /| /| 23| Shape speed| 0-63| Rasius size,static
64-158| Max to min speed,closing eﬀect
159-160| Stop
161-255| Min to max
/| 24| /| /| 24| Shape fade| 0-5| Snap
16| Smooth,fading cure gamma 0,5
17| Smooth,fading cure gamma 0,506
18| Smooth,fading cure gamma 0,513
19-244| Smooth,fading cure gamma 1,993
243| Smooth,fading cure gamma 1,986
245| Smooth,fading cure gamma 2
246-255| Smooth,fading cure with automatic gamma
/| 25| /| /| 25| Shape R| 0-255| 0-100% Shape Red
/| 26| /| /| 26| Shape G| 0-255| 0-100% Shape Green
/| 27| /| /| 27| ShapeB| 0-255| 0-100% Shape Blue
/| 28| /| /| 28| Shape W| 0-255| 0-100% Shape White
/| 29| /| /| 29| Shape dimmer| 0-255| 0-100% shape dimmer
/| 30| /| /| 30| Background dimmer| 0-255| 0-100% background dimmer
/| 31| /| /| 31| Shape transition| 0-4| No fade
5| 100ms
6-73| 0,5sec
74-113| 1sec
114-171| 2sec
172-216| 3sec
217-255| 4sec
/| 32| /| /| 32| Shape oﬀset| 0-9| Continuous
10-255| Random distribution of ﬂash from 2to 20 ﬁxtures

/

|

33

/

|

35

| | | | | 108| Slow pulsation (0,5 ﬂash/sec)
109-207| Fast pilsation (25 ﬂash/sec)
208-212| Open
213-225| Random slow strobe
/| /| 35| Background select| 0-255| Background select
22| 22| 36| Red LED 1| 0-255| 0-100%Red LED linear dimmer
23| 23| 37| Green LED 1| 0-255| 0-100%Green LED linear dimmer
24| 24| 38| Blue LED 1| 0-255| 0-100%Blue LED linear dimmer
/| 25| /| White LED 1| 0-255| 0-100%White LED linear dimmer
…| …| …| Red LED …| 0-255| 0-100%Red LED linear dimmer
…| …| …| Green LED …| 0-255| 0-100%Green LED linear dimmer
…| …| …| Blue LED …| 0-255| 0-100%Blue LED linear dimmer
/| …| /| White LED …| 0-255| 0-100%White LED linear dimmer
76| 94| 90| Red LED 19| 0-255| 0-100%Red LED linear dimmer
77| 95| 91| Green LED 19| 0-255| 0-100%Green LED linear dimmer
78| 96| 92| Blue LED 19| 0-255| 0-100%Blue LED linear dimmer
/| 97| /| White LED 19| 0-255| 0-100%White LED linear dimmer

MAINTENANCE AND CLEANING

The following points have to be considered during the inspection:

All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded.
There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, suspension, trussing).
Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
The electric power supply cables must not show any damage, material fatigue or sediments.

Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.

| CAUTION
Disconnect from mains before starting maintenance operation.
|
---|---|---

In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the lights.

Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust.
Clean the fan each week.
A detailed electric check by approved electrical engineer each three month, make sure that the circuit contacts are in good condition, prevent the poor contact of circuit from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.
Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.

ADD 3rd Floor, No. 288, Guangzhu East Line, Pingwen, Lanhe Town,Nansha District, Guangzhou, China
Tel. +86 20 8499 2310/2320/2330
Fax +86 20 8499 2360

E-mailinfo@color-imagination.com
Websitewww.color-imagination.com
Follow uson
www.facebook.com/color.imagination.1
www.youtube.com/user/colorimaginationj
twitter.com/colorimaginej