rako RMT-500 500W Trailing Edge Wireless Dimmer Instruction Manual

rako RMT-500 500W Trailing Edge Wireless Dimmer

Product Information

Specifications:

• Model: RMT-500
• Power Output: 1W minimum, 500W maximum
• Compatibility: Mains dimmable LEDs, tungsten, and incandescent lamps
• Wireless Control: Works with any Rako device that transmits wireless messages

Product Usage Instructions

Installation:

1. Installation should only be carried out by a competent electrician.
2. RMT-500 modules should be mounted in areas that are adequately ventilated, dry, and outside of any enclosed metal casings that may interfere with the wireless signal.
3. Modules should be mounted vertically, with the terminals at the bottom, or horizontally.
4. Ensure the cable clamp is fitted tightly to secure the cables.

Initial Checks:

• When power is initially connected, the load should power up to full brightness.
• Use the clear button as a manual on/off switch for testing.
• The internal LED behind the clear button flickers when receiving any wireless message.

Programming the RMT-500:

1. Ensure the RMT-500 is powered up and working with the setup button.
2. Follow the Wireless Module Setup Guide for programming instructions.

FAQ:

• Q: What should I do if I experience bad wireless reception with the RMT-500?
  A: If you are experiencing bad wireless reception, where there are intermittent pulses on the LED when any wireless message is sent, it is recommended to install a wireless repeater (WRB-100) to improve the wireless range.

For more information relating to the RMT-500 see the Wireless Module Application Sheet, Wireless RAK Application Sheet, and Wireless Device LED Diagnostics.
For programming a wireless system, include the device in this manual: Wireless Module Programming Guide.

What is the RMT500

• The RMT-500 is a wireless trailing edge dimming module designed for mains dimmable LEDs as well as tungsten and incandescent lamps.
• The RMT-500 dimmer modules are not suitable for inductive loads such as wire-wound transformers or electric motors.
• The RMT-500 can be controlled by any Rako device that transmits wireless messages.

Loadings

NB
Derating is a precaution to account for varying characteristics in the lighting loads; this can i nclude inrush currents and higher ambient temperatures, as well as recommendations from 3rd party lighting manufacturers.

Installation

WARNING: Installation should only be carried out by a competent electrician.

• RMT500 modules should be mounted in areas that are adequately ventilated, dry, and outside of any enclosed metal casings that may interfere with the wireless signal.
• Modules should be mounted vertically, with the terminals at the bottom, or horizontally.
• While the modules are designed to be maintenance-free, they should be mounted in an accessible location should investigation or re-addressing of the units be necessary.
• Ensure that the cable clamp is fitted tightly to secure the cables.

Initial checks

• When power is initially connected to the module, the load should power up to full brightness.
• The clear button can be used as a manual on/off switch to test the circuit.
• The internal LED behind the clear button will flicker when the module receives any Rako wireless message and is a useful diagnostic indicator. The LED feedback becomes inactive after 20 minutes to avoid a nuisance light spill but can be re-activated by pressing the clear button.

Programming the RMT-500
Once the RMT-500 has powered up and has been tested working with the setup button, the device is ready to be programmed. For instructions on how to program the RMT-500, see the Wireless Module Setup Guide.

Appendix 1: LED Diagnostics

be four rapid pulses on the LED when any wireless message is sent.
Bad wireless reception| | When the unit is out of range, there will be intermittent pulses on the LED when any wireless message is sent.

NB

It is recommended to install a wireless repeater (WRB-100) if you are experiencing intermittent wireless range.

Should the module not respond to any of the above, check the supply voltage.

Thank you for choosing Rako Controls; we hope that you are pleased with your system. Should you require further assistance, please contact us via our website, www.rakocontrols.com, or by calling our customer support helpline on 01634 226666.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>