FRIDJA F2500-BLK Slow Juicer Instruction Manual
- May 15, 2024
- FRIDJA
Table of Contents
FRIDJA F2500-BLK Slow Juicer
INTRODUCTION
Thank you for purchasing this Fridja f2500 slow juicer! As with any new electrical product please allow several hours of use before all components have acclimatised themselves with your surroundings and settled into optimum operation.
Please follow the instructions in the manual carefully. The appliance cannot be covered under the manufacturer warranty if the product is abnormally or commercially used. This appliance is for household use only.
Brand: Fridja | Model Number: F2500/BLK
Input Voltage: 220-240V 50/60 Hz | Power Consumption: 300W
Maximum Use: Less than 20 minutes | Instruction Booklet: 1.0
SAFETY WARNINGS
- Read all the instructions carefully before use.
- To protect against risk of electrical shock and permanent damage to the juicer, do not submerge the base of unit in water or other liquid.
- Close supervision is necessary when using any appliance near children.
- Unplug the juicer from plug socket when not in use, before putting on or taking off parts, and before cleaning.
- Avoid contact with moving parts.
- Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, is dropped, or damaged. Return appliance to the nearest authorised service facility for examination, repair, electrical or mechanical adjustment.
- The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.
- Do not use outdoors.
- Do not let the cord hang over the edge of table or counter.
- Always make sure the juicer cover is clamped securely in place before the juicer is turned on. Do not open or remove the juice jug while in operation.
- Be sure to turn switch to OFF position after use. Make sure the motor stops completely before disassembling.
- Do not put your fingers or other objects into the juicer opening while it is in operation. Only push produce with the pusher.
- Always check the silicone valve lip is inserted into the bowl before use.
- Do not operate without the juice/pulp containers in place.
- Do not alter the appliance in anyway.
- Do not use the appliance for anything other than its intended purpose as described in the manual.
- The appliance should be used for a limited period of time (no longer than 20 minutes continuously).
JUICING TIPS
Juicer damage due to owner negligence or from not following the instructions in the owner’s manual will void the warranty service.
Please be careful! We recommend you juice slowly! Enjoy the process. Do not rush, what’s the hurry?
- Ha r d Fruit – Carrots and beetroots should be juiced first when mixed with high yield fruit such as apples and pears for best results.
- Fibrous and/or tough leafy ingredients – Fibrous ingredients like celery and kale should be cut into small lengths before juicing and mix with high yield fruit. If the juicer becomes stuck, run in reverse or remove. Use the pusher to push through if necessary.
- Seeded Fruit – ingredients with seeds like grapes, afterwards always thoroughly clean all the bottom of the auger.
- Nuts (for nut milk) – Always soak overnight before putting them in the juicer.
DO NOT put the following ingredients into the juicer:
- Ice – Do not use ice inside the juicer. Add ice afterwards. Even better, refrigerate the fruit/vegetables before juicing.
- Hard seeds – Peach, nectarines, apricot, plum, mango, etc. Remove from the stones before juicing.
- Skins – Pineapple, melon, mango, orange, etc. Peel the skins from fruit before juicing. If you don’t eat it, don’t juice it!
- Sesame seed, butter, margarine – Do not extract ingredients containing vegetable or animal oil. This can reduce performance and permanently damage the juicer.
- Coconut, sugarcane, whole grains – Do not extract ingredients with no water content. They will damage the juicer.
We constantly update our social media with recipes, tips and more. Why not
check them out now?
Scan the QR codes on the front or back page!
YOUR FRIDJA JUICER
- Juicing Jug
- Auger
- Juicing Bowl with Anti Drip Tap
- Base
- Juice Jug
- Pulp Jug
- Pusher
- Cleaning Brush
- On/Off/Reverse Rotary Knob
ANTI DRIP TAP
Use the anti drip tap to minimise mess and to mix different fruit and
vegetable juices.
Once the juice bowl is full, release the juice by opening the anti drip tap.
-
Open
-
Closed
HOW TO ASSEMBLE
For a YouTube video on how to assemble scan this QR code or go to this link:
https://www.youtube.com/Fridja
Wash the parts before first use. The juicer may leak and not turn on if assembled incorrectly.
-
Always check the silicon valve plug is inserted into the bowl (particularly after washing).
-
Position the juice bowl onto the base, aligning the juice and pulp spouts.
-
Once the bowl is in position, place the auger firmly into the centre of the bowl. Make sure it touches the bottom, otherwise it will not be possible to close the cover of the juicing jug.
-
Position the juicing jug so that the ▲ on the chute aligns with the padlock. Twist the juicing bowl until it clicks. This will release the safety mechanism.
-
Place the juice and pulp jugs under the correct spouts. The juice jug has measurements and a spout to pour. it’s juice time!
HOW TO JUICE
For a product overview YouTube video scan this QR code or go to this link:
https://www.youtube.com/Fridja
Wash and prepare all your ingredients. Plug the power cord into a wall plug socket.
- Open the lid and add fruits and vegetables into the juicing jug. Make sure to note which fruits and vegetables are recommended according to this manual.
- Close the lid and ensure the anti drip tap is closed.
- Rotate the rotary knob to the on position.
On position – Pulls down and slowly masticates the ingredients.
Reverse position: Pushes the ingredients back up to dislodge them.
- If you are juicing a mixture of hard and soft fruits, juice the hard fruit first.
- Use the anti-drip tap to make mixed juices and stop juice from escaping the juicing bowl. Juicing with the anti-drip tap closed creates various mixed juice creations when different fruits and vegetables are juiced. Open the anti drip tap to pour juice into the juice jug. After juicing, close the anti-drip tap to stop the juice from dripping, especially when disassembling the juicing bowl off the base.
- After the fruits and vegetables are completely extracted from the juicing jug, switch the unit OFF.
After each extraction, run the juicer for an additional 30 seconds to let the juicer extract the remaining pulp. Clean the juicer immediately. Details are on the following pages.
Your juicer has a safety mechanism when it overheats. The juicer will switch off automatically. If the juicer switches off, turn the rotary knob to ‘off’. Wait at least 10 minutes to let the juicer cool down before turning back on.
MAKING NUT MILK
Using almond or cashew nut milk instead of dairy is a fantastic idea and really simple to do with your new juicer. Assemble the juicer and use the juice filter, just like you were going to make juice.
Soak nuts such as almonds overnight in a bowl. The next day replace the water with fresh water. Add the nuts along with the fresh water using a ladle into the juicer for delicious nut milk!
HOW TO DISASSEMBLE
Turn the rotary knob to OFF and unplug the power cord from the plug socket. Extract all the remaining produce in the juicing bowl before stopping the juicer. For easier clean up, operate the juicer for an additional 30 seconds after the juicer has finished extracting.
-
Close the anti drip tap. Remove the pulp and juice jugs.
-
Remove the juicing jug by rotating anti-clockwise until the ▲ on the chute aligns with the padlock. Lift the juicing jug off.
-
Remove the auger by lifting from the bowl. If it is stuck, gently rotate until loose.
-
Lift the bowl from the base.
Immediately clean the juicer after each use. If remaining residue in the juicer dries up, it can make disassembling and clean-up difficult. The excess build up can cause poor performance in future uses.
HOW TO CLEAN
It’s important to keep your juicer clean to ensure its long life. Switch off the juicer and unplug. Wash all parts with warm soapy water. If the mesh on the juicer jug is clogged with pulp, use the supplied cleaning brush.
Please note:
- Do not use an iron wire brush to clean.
- If you use the dishwasher, It is important to not wash above temperatures of 40°C.
-
When washing the bowl, remove the silicone valve from the socket. This will make it easier to clean.
-
Clean the seal ring of the bowl by turning the bowl upside down and pushing the ring out with your thumb.
-
When putting the seal ring back in, the small ribbed surface should at the bottom/outside the bowl. The flat side should be inside the bowl.
When cleaning the base, never submerge it under water. Simply wipe it clean using with a damp cloth.
After cleaning, please make sure all parts are fully dry before reassembling
TROUBLESHOOTING
When there is no power to the juicer:
- Check if the power cord is properly plugged into the plug socket (and the plug socket is turned on).
- Check if the drum lid and the juicing bowl are properly assembled. Watch the video on how to assemble! It won’t turn on if assembled incorrectly.
- If the juicer stops due to the overload protection, let the juicer cool before juicing again.
Low juice yield:
- Different ingredients hold different amounts of fluid that will yield different amounts of juice. If the ingredients are not fresh, they may contain reduced amounts of fluid, which will yield less juice.
- Check if the silicone valve lip is firmly inserted into the bowl to ensure no juice is leaking.
- If the ingredients have low water content, it may help to soak them in water before juicing. If juicing ingredients with small seeds, the yield may reduce due to seed residue.
- For certain fruit, disassemble and wash the top-set in between juicing. If there is seed residue on the bottom of the auger, this can affect juicer performance and the overall juice yield.
There is too much pulp in the juice:
- When continuously juicing, depending on the ingredients, the juice may contain a lot of fine pulp. To reduce the fine pulp, clean the juicer jug frequently.
- Use an external sieve and put the juice through it to collect the unwanted pulp.
- If the juice jug and the auger are damaged and affecting the juicer’s performance, it is recommended the parts be replaced. The lifetime of each part may vary depending on length and method of use and ingredients extracted.
The drum lid will not close:
- Make sure the auger is pushed all the way in to the strainer in order for the drum lid to close properly. If the auger is not properly in position, the drum lid may not close.
Odd noise from the juicer:
- Check if the parts are assembled correctly. Try reassembling the parts and listen for the odd noise. Do not start the juicer unless there are ingredients and/or liquid in it.
- If excessive noise occurs when ingredients are inserted into the juicer, check the size of the ingredients. Try cutting up dense/stringy/hard fruits and vegetables.
- Noise can occur if the juicer is operated on an uneven or slanted surface. Place the juicer on a horizontally flat surface when operating.
Juice dripping down the body of the base:
- If the silicone valve lip on the bottom of the juicing bowl is not plugged in correctly, the juice may seep out on to the juicer base. Before assembling the parts, check and make sure the compression silicone is plugged in correctly
Discolouration of the plastic parts:
-
After juicing, if the juicer is not cleaned right away, the remaining pulp inside the juicing jug and auger can dry up which can make disassembling and cleaning hard.
This can also affect the juicer’s performance and colour. -
Ingredients that are rich in carotenoid such as carrots and spinach may dye plastic parts. When the parts are dyed with carotenoid please use mild detergent to clean.
-
Do not use vegetable oil on the juicer. Vegetable oil or oil from animal fat affects the juicer’s performance and will result in damaged parts.
Using for purposes other than juicing:
- This juicer is designed to juice ingredients like fruits and vegetables. Do not use the juicer for extracting vegetable oil.
GUARANTEE
This guarantee is applicable for goods bought directly from Fridja. If you purchased your juicer from another vendor, please contact them.
If by chance you are unhappy with your purchase, please contact us within fourteen days of delivery for a refund. Returned items must be in unused condition with all supplied Fridja accessories and packaging. You are responsible for the condition of your goods until they reach us, so pack your items carefully to prevent damage in transit. Worn, damaged, or incomplete returns will not be eligible for a refund and will be returned to you.
All our goods are supplied with a 12 month warranty from the date of purchase, covering defects in materials and workmanship under conditions of normal use and maintenance. If your goods develop a fault within this period, we will repair or replace the item. If we cannot do this we will refund your actual purchase price.
If goods become defective within three months of delivery, we will pay for
collection of the items and delivery of the replacement. After this time, we
will not pay to collect items.
In the unlikely event that your goods arrive damaged, please inform us within
24 hours of delivery, including photos of the damage. The claim will be
assessed, and if approved we will arrange for the goods to be collected, and
we will replace or refund as necessary.
It is your responsibility to securely package items for their safe return to us using a trackable service. Not doing so will void your warranty.
To arrange the return of your item please contact: info@fridja.com.
This guarantee is subject to the following provisions:
- The product must be correctly installed and operated in accordance with the instructions contained in these operating instructions.
- This guarantee does not cover accidental damage or misuse.
- This guarantee will be rendered invalid if the product is resold or has been damaged by inexpert repairs. The manufacturers disclaim any liability for incidental or consequential damages.
This guarantee is in addition to, and does not diminish, your statutory or legal rights.
PLUG SAFETY
Your appliance is supplied with a non-rewireable plug fitted to the mains lead and should the fuse need replacing, you must use an ATSTA approved one (conforming to BS1362) of the same rating. If in doubt, consult a qualified electrician.If you need to remove the plug – DISCONNECT IT FROM THE MAINS and then cut off the mains lead and immediately dispose of it safely. Never attempt to re-use the plug or insert it into a socket outlet as there is a danger of an electric shock.
CORRECT DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL & ELECTRONIC EQUIPMENT)
This marking on the product, accessories, or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
CUSTOMER SUPPORT
UK REGISTERED ADDRESS
FAIRFIELD, CAMDEN HILL, KENT,
TN17 2AR, UNITED KINGDOM
EU REGISTERED ADDRESS
77 CAMDEN STREET, DUBLIN 2, D02
XE80, REPUBLIC OF IRELAND
www.fridja.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>