COWSAR Z5820AF Portable Automatic Ice Maker Instruction Manual

COWSAR Z5820AF Portable Automatic Ice Maker

Product Information

• Specifications
  • Model: HZB-12/H
  • Type: Portable Automatic Ice Maker
  • Manufacturer Contact: 213-4467172 or 661-4358826

Product Usage Instructions

• Important Safety Tips
  • Do not operate the ice maker with a damaged cord. Replace damaged cords to avoid hazards.
  • Position the ice maker where the plug is accessible and connect to properly polarized outlets only.
  • Avoid running the power cord over carpeting or heat insulators. Keep the cord away from water and traffic areas.
  • Avoid using extension cords. If necessary, use a No.14AWG minimum size cord with rated watts no less than 1875W.
  • Unplug the ice maker before cleaning, repairing, or servicing.
  • Exercise caution when using the appliance near children.
  • Do not use the ice maker outdoors or with liquids other than water.
  • Ensure proper clearance around the unit for ventilation and avoid direct sunlight exposure.
  • Do not clean the ice maker with flammable fluids or tip it over.
  • If bringing the ice maker indoors from outside in winter, allow it to warm up before plugging it in.
  • The appliance must be earthed and repaired only by trained service personnel.
• Installation Guidelines
  • Install the ice maker according to ASHRAE15 safety standards for Refrigeration Systems.
  • Avoid installing the ice maker in corridors or hallways of public buildings.
  • Service or component replacement should be carried out by authorized service personnel to prevent hazards.
• Cleaning and Maintenance
  • Regularly clean the ice maker following the manufacturer’s instructions.
  • Use a soft cloth and mild detergent to clean the exterior.
  • Do not use abrasive cleaners or immerse the unit in water.
• Frequently Asked Questions (FAQ)
  • Q: Can I use an extension cord with the ice maker?
  • A: It is not recommended to use an extension cord with the ice maker. If necessary, use a No.14AWG minimum size cord with rated watts no less than 1875W.
  • Q: Can I clean the ice maker with flammable fluids?
  • A: No, do not clean the ice maker with flammable fluids as it can create a fire hazard or explosion. Use a soft cloth and mild detergent for cleaning.
  • Q: How should I position the ice maker for optimal performance?
  • A: Place the ice maker away from direct sunlight with at least 4 inches of clearance from walls on all sides to ensure proper ventilation and performance.

IMPORTANT SAFETY INSTRUCTIONS

• Your safety and the safety of others are very important.
• We have provided many important safety messages in this manual and on your appliance.
• Always read and obey all safety messages.
• This is the safety alert symbol:
• All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”.

DANGER

• These words mean:
  • Serious injury may occur if you don’t immediately follow instructions.
  • All safety messages will tell you what the potential hazard is, how to reduce the chance of injury, and what could happen if the instructions are not followed.

PREPARING YOUR ICE MAKER FOR USE

IMPORTANT SAFETY TIPS: When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliances.

• Do not operate this ice maker, or any other appliance with a damaged cord
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person to avoid a hazard.
• This ice maker must be positioned where the plug is accessible.
• Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the socket.
• Do not run the power cord over carpeting or other heat insulators. Do not cover the cord.
• Keep the cord away from traffic areas and do not submerge it in water.
• We do not recommend the use of an extension cord, as it may overheat and become a risk of fire.
• If you must use an extension cord, the cord must be of No.14AWG minimum size with its rated watts no less than 1875W.
• Unplug the ice maker before cleaning or making any repairs or servicing.
• Exercise caution and use reasonable supervision when the appliance is used near children.
• Do not use your ice maker outdoors. Place the ice-maker away from direct sunlight and make sure that there is at least 4 inches of clearance between the back of your unit and the wall.
• The minimum clearance from each side of the unit must be no less than 4 inches.
• Do not use any liquids other than water to make the ice cube.
• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
• Do not tip it over.
• If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to room temperature before plugging it in.
• WARNING: This appliance must be earthed.
• DANGER – Risk Of Fire or Explosion. Flammable Refrigerant Used. Do Not Use
• Mechanical Devices To Defrost Ice Maker. Do Not Puncture Refrigerant Tubing.
• DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be
• Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.
• CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult the Repair Manual/Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed.
• CAUTION – Risk Of Fire Or Explosion. Disposal Of Property Under Federal Or Local Regulations. Flammable Refrigerant Used.
• CAUTION – Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing;Follow Handling Instructions Carefully. Flammable Refrigerant Used.
• The ice maker should be installed per the safety standard for Refrigeration Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public buildings.
• If problems that need servicing occur, such as the replacement of some components, the servicing shall be done by service personnel authorized by the factory to minimize the risk of possible ignition due to incorrect components or improper service.

IMPORTANT:

• The wires in this main lead are coloured per the following code: Grounding
• White:   Neutral
• lack:  Live

To avoid a hazard due to the instability of the appliance, it must be placed on an even or flat surface.

PACKING LIST

GETTING TO KNOW YOUR UNIT

General instruction

1. Ice scoop
2. Ice full sensor
3. Ice basket
4. Top cover with transparent window
5. Air exhausting
6. Water drain cap: at the front bottom side of the unit.
7. MAXIMUM WATER LEVEL: ▲ Remove the ice basket, and you can see the water level mark.
8. Handle.

AUTOMATIC SELF-CLEANING PROGRAM

• Plug in the unit and press “ON/OFF” button on the control panel for more than 5 seconds.
• It takes 30 minutes to enter the self-cleaning program.
• The “Ice Full, Add Water” indicator flashes during the cleaning.
• After cleaning, drain the water from the inner tank through the drainage outlet at the bottom of the machine.

OPERATING PROCEDURES & MAINTENANCE

Position of control panel & function
Control Panel: easy to use, visible function setting on touch display.

• A. Button to turn on/off the unit.
• B. Power indicator
• C. Ice Full indicator
• D. Water shortage indicator

UNPACKING YOUR ICE MAKER

1. Remove the exterior and interior packaging. Check if all the accessories are included. If any parts are missing, please contact our customer service.
2. Remove the tapes used to fix the ice shovel, ice basket and ice scoop. Clean the tank and the ice basket.
3. Put the ice maker on a level and flat countertop away from direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Make sure that the minimum clearance between the wall and the back, left, and right sides of the unit should be at least 4 inches.
4. Allow two hours for the refrigerant fluid to settle before plugging in the ice maker.
5. The appliance must be positioned where the plug is accessible.

WARNING: Fill with drinking water (potable water) only.

ASSEMBLE HANDLE

• Rotate the handle to the same angle as the mounting hole on the machine.
• Make sure the handle is inserted into the machine.

CONNECTING YOUR ICE MAKER DANGER

Improper use of the grounding plug can result in the risk of electrical shock. If the power cord is damaged, please call our customer service.

1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which matches with standard three-prong wall outlets to minimise the possibility of electric shock.
2. Plug your appliance into a specialized grounding wall outlet that is properly installed. Do not, under any circumstances, cut or remove the third (grounding) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician.
3. This appliance requires a standard 110-120 volt, 60Hz electrical three-prong grounding outlet.

CLEANING AND MAINTAINING YOUR ICE MAKER

Before using your ice maker, it is strongly recommended to clean it thoroughly.

1. Take out the ice basket.
2. Clean the interior with diluted detergent, warm water and a soft cloth.
3. Then rinse the inner parts with water and drain out the water by unplugging the drain cap on the front bottom side.
4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
5. Dry the interior and exterior with a clean soft cloth.
6. When the machine is not in use for a long time, drain the water completely out and dry the interior.

USING YOUR ICE MAKER

1. Open the cover, remove the ice basket and pour water into the tank. Keep the water level below the maximum water level mark.
2. Press the “ON/OFF” button on the control panel to begin the ice-making cycle.
3. The ice-making cycle lasts approximately 6 to 13 minutes, which depends on the selection of ice cube size and the room temperature. The recommended room temperature is 50℉ to 105℉.
4. If the water pump can’t inject water, the ice maker will stop automatically and the “ADD WATER” indicator will be on. Press the “ON/OFF” button, add water to the max water level mark, and press the “ON/OFF” button to turn on the unit again. Allow at least 3 minutes for the refrigerant liquid inside the compressor to settle before restarting.
5. The ice maker stops when the ice basket is full and the “ICE FULL” indicator will be on.
   • Warning: Direct sunlight or sunlight reflection may cause infrared sensor malfunction. If the unit doesn’t stop even when ice cubes obstruct the sensor, move the unit to where there is no sunlight.
6. Change water in the water reservoir every 24 hours to ensure a reasonable hygienic level. If the unit isn’t to be used, drain all the water and dry the tank.

TROUBLESHOOTING

add water, and

press the “ON/OFF” button again to restart the unit.

The “ICE FULL” indicator is on.| Ice is full in the basket.| Remove ice cubes from the ice basket.

Continuously press the “on/off” button for 5 seconds and the unit could make ice for 10 cycles even when the “Ice” indicator is on.

Ice cubes stick together.| The ice-making cycle is too long.| Stop the ice maker and restart it after the ice melts. Select ice cubes of a smaller size.
The water temperature in the inner tank is too low.| Change the water. The recommended water temperature is 40℉ – 90℉
The ice-making cycle is normal but no ice cube is formed.| The room temperature or the water temperature in the inner tank is too high.| The room temperature should be 50℉ – 105℉ and the water temperature should be 40℉ – 90℉
The refrigerant in the cooling system leaks.| Verify it by a qualified technician.
The pipe in the cooling system is blocked.| Verify it by a qualified technician.

TECHNICAL PARAMETERS

TECHNICAL PARAMETERS & CIRCUIT DIAGRAM

EXPLOSIVE DRAWINGS

S/N| Part description| Qty/

Per

| S/N| Part description| Qty

/Per

| S/N| Part description| Qty/

Per

---|---|---|---|---|---|---|---|---
1| Power cord| 1| 13| Ice shovel| 1| 25| Inner tank bracket, RH| 1
2| Plastic clip| 1| 14| Evaporator| 1| 26| Stainless wire| 1
3| Back panel| 1| 15| Micro switch| 2| 27| Water supply pipe| 1
4| Plate back support| 1| 16| Inner tank bracket, LH| 1| 28| Synchronous motor| 1
5| DC water pump| 1| 17| Back bottom panel| 1| 29| Condenser| 1
6| Silicon pump sealing| 1| 18| Back top panel| 1| 30| DC fan motor| 1
7| Handle| 1| 19| Displaying PCB| 1| 31| Nylon plug drain| 1
8| Control box cover| 1| 20| Touchpad| 1| 32| Copper tube filter| 1
9| Main PCB| 1| 21| Front top panel| 1| 33| Plastic bottom| 1
10| Control box| 1| 22| Water filter| 1| 34| Compressor| 1
11| Ice making box| 1| 23| Ice scoop| 1| 35| Magnetism valve| 1
12| Ice scoop link| 2| 24| Ice basket| 1|  |  |

Thank you for purchasing this product! If you have any questions about the product, such as missing parts, damaged products, product assembling, and operation, please contact us via Amazon Message or customer service number: 213-4467172 or 661-4358826

IMPORTANT: Please call our customer service department for any consulting:

• 213-4467172
• 661-4358826
• (8:30 am – 5:30 pm P.S.T.)
• DATED PROOF OF PURCHASE IS REQUIRED FOR WARRANTY SERVICE.
• Address: ROWAN ELECTRIC APPLIANCE LLC 28407 Ascent Way,
• Santa Clarita, CA 91350
• Phone: 213-4467172 or 661-4358826

Thank you for purchasing this product! Please read the instructions carefully before using your portable ice maker. If you have any questions about the product, please contact us via Amazon Message or customer service number: 213-4467172 or 661-4358826

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>