AVIBG21 Avi-on Internal Fixture Adapter User Manual
- June 16, 2024
- avi-on
Table of Contents
AVIBG21 Avi-on Internal Fixture Adapter
Product Information
Specifications:
- HVIN: AVI-B-IFAC-5A, AVIB-IFAC-5A-2CH
- Input voltage: 120/277VAC 50/60Hz
- AC: AWG14 – AWG20, Cu only, Sol./Str.
- C US LISTED Fixture Adapter E519564
- Output: 120/277VAC 50/60Hz, 5A for General Use/Tungsten/Electronic Ballast/Magnetic Ballast
- DC: AWG18 – AWG22, Cu only, Sol./Str.
- Manufacturer: Avi-on Labs, Inc., Park City, USA
- Country of Origin: Made in China
- Strip Length: 9 – 10mm
- Compliance: CAN ICES-005 (B) / NMB-005 (B)
Product Usage Instructions
Mounting the IFA:
- Select a suitable listed junction box for installation.
- Determine the size of the junction box according to the National Electrical Code (NEC) or Canadian Electric Code, Part 1 (CEC), and the product size of 15334.823.1mm.
- Follow the included wiring diagram to connect the IFA, lighting driver, and lights.
- Double-check the wiring before closing the junction box.
Disconnecting or Connecting the Terminal Head:
To disconnect or connect the terminal head, press it back firmly.
FAQs
-
Q: Can I use the AVI-IFAC-5A device without connecting a sensor?
A: Yes, it is not necessary to connect a sensor for normal use of the AVI- IFAC-5A device. -
Q: What type of sensors can be used with the AVI-IFAC-5A device?
A: Avi-on provides both Passive IP (AVI-DC-PIR) and Microwave (AVI-DC-MW) Sensors that can be used with or without ALS Capabilities. -
Q: Is the IFA suitable for mounting in a junction box?
A: Yes, the IFA is suitable for mounting in a junction box. -
Q: What is the strip length for the IFA?
A: The strip length for the IFA should be between 9 and 10mm.
INSTALLING YOUR IFA
- Installation work and electrical wiring must be done by a qualified person(s) by all applicable codes and standards, including fire-rated construction.
- A suitable listed junction box shall be provided during installation.
- Size of the junction box is to be determined by the National Electrical Code (NEC) (ANSI/NFPA 70), or Canadian Electric Code, Part 1 (CEC), and the product size is 15334.823.1 mm.
- Mounting screws are not provided. Secure the FA to the junction box firmly with screws.
- The junction box may be located on a wall or ceiling surface adjacent to the light fixture.
- Connect FA, Lighting driver and Lights according to the included wiring diagram.
- Double-check the wiring before closing the junction box.
- WARNING: RISK OF FIRE AND ELECTRIC SHOCK – Never attempt to alter, modify or destroy a lighting fixture to wire the IFA.
Note: Sensor interface can be connected to Avi-on Direct Connect Sensors.
This product could be divided into two versions – general and high
configuration: general configuration will not be equipped with sensor
subassembly, high configuration is equipped with sensor. Sensor subassembly is
provided by the franchiser.
Note: The AVI-IFAC-5A device comes equipped with a sensor connector for use with external sensors. Avi-on provides both Passive IP (AVI-DC-PIR) and Microwave (AVI-DC-MW) Sensors that cab be used with or without ALS Capabilities. It is not necessary to connect a sensor for normal use of the AVI-IFAC-5A device.
SPECIFICATION
- Input voltage: 120/277VAC 50/60Hz
- Output: 120/277VAC 50/60Hz, 5A for General Use/Tungsten/Electronic Ballast/ Magnetic Ballast
- Operating temperature: -20~75°C
- AC: AWG14 – AWG20, Cu only, Sol./ Str.
- DC: AWG18 – AWG22, Cu only, Sol./ Str.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment must be installed and operated by
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Suitable for Use in Other Environmental Air Spaces
(Plenums) by Section 300.22, (C) of the National Electrical Code
Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- (1) This device may not cause interference: and (2) This device must accept any interference. including interference that may cause undesired operation of the device.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
CAN ICES-005 (B) / NMB-005 (B)
For Control of Electronic Ballast, CFLs, LED, and LED Lamps.
For junction box mounting.
Connector provided for field connection.
CAUTION: High Voltage – Disconnect power supply before servicing.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>