milwaukee M12 FIWF12 Cordless Impact Wrench Instruction Manual

milwaukee M12 FIWF12 Cordless Impact Wrench

Instructions

Remove the battery pack before starting any work on the machine.

Handle (insulated gripping surface)

TECHNICAL DATA

CORDLESS IMPACT WRENCH : M12 FIWF12:  M12FIWP12 : M12FIW14 : M12 : FIW38

• Production code……………………………………………………………………4678 13 01… ……… 4690 05 01… ……… 4677 95 01… 4678 02 01……000001-999999

• Tool reception ……………………………………………………………………….1/2″ (12,7 mm) …….1/2″ (12,7 mm) …….. 1/4″ (6,35 mm) ……. 3/8″ (9,5 mm)

• No-load speed mode 1 ………………………………………………………0-1200 min-1 ………..0-1200 min-1 ………… 0-1300 min-1 ……….. 0-1200 min-1

• No-load speed mode 2 ………………………………………………………0-1800 min-1 ………..0-1800 min-1 ………… 0-1900 min-1 ……….. 0-1800 min-1

• No-load speed mode 3 ………………………………………………………0-2700 min-1 ………..0-2700 min-1 ………… 0-3200 min-1 ……….. 0-2700 min-1

• No-load speed mode …………………………………………………….0-2700 min-1 ………..0-2700 min-1 ………… 0-3200 min-1 ……….. 0-2700 min-1

• Impact range mode 1…………………………………………………………0-1100 min-1 ……….. 0-1100 min-1 ………… 0-1300 min-1 …………0-1100 min-1

• Impact range mode 2…………………………………………………………0-2100 min-1 ………..0-2100 min-1 ………… 0-2000 min-1 ……….. 0-2100 min-1

• Impact range mode 3…………………………………………………………0-3200 min-1 ………..0-3200 min-1 ………… 0-4300 min-1 ……….. 0-3200 min-1

• Max. Torque ………………………………………………………………………….339 Nm ……………… 339 Nm ………………..115 Nm ……………….339 Nm

• Max. diameter bolt / nut. ………………………………………………………. M16 …………………. M16 …………………….M12 …………………. M16

• Battery voltage………………………………………………………………………..12 V ………………….. 12 V …………………….12 V ……………………12 V

• Weight according EPTA-Procedure 01/2003 (2.0 Ah) ………………….1,1 kg ………………… 1,1 kg …………………0,92 kg …………………1,1 kg

• Weight according EPTA-Procedure 01/2003 (4.0 Ah / 6.0 Ah)

• Recommended ambient operating temperature ………………………..1,37 kg ………………. 1,37 kg …………………1,15 kg ……………….1,37 kg

• Recommended battery types……………………………………………………………………………………….-18°C … +50 °C

• Recommended charger …………………………………………………………………………………………………… M12B…
  Noise/vibration information

• Measured values determined according to EN 62841.

• Typically, the A-weighted noise levels of the tool are:

• Sound pressure level (Uncertainty K=3dB(A)) …………………………………….. M12-18 C; M12-18 FC; M12-18 AC; M12 C4; C12 C

• Sound power level (Uncertainty K=3dB(A)) …………………………..107,82 dB (A) ……… 107,82 dB (A)………..102,86 dB (A) ………107,82 dB (A)
  Wear ear protectors!

• Total vibration values (vector sum in the three axes)

• determined according to EN 62841.

• Vibration emission value ah

• Impact tightening of fasteners of the maximum capacity of the tool ……10,26 m/s2 ………….. 10,26 m/s2 …………….15,77 m/s2 …………..10,26 m/s2

• Uncertainty K= ……………………………………………………………………1,5 m/s2 ……………… 1,5 m/s2 ………………..1,5 m/s2 ………………1,5 m/s2

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

IMPACT WRENCH SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:

• it is tilted in the workpiece to be machined

• it has pierced through the material to be machined

• the power tool is overloaded
  Do not reach into the machine while it is running. The insertion tool may become hot during use.

• when changing tools

• when setting the device down

• Sawdust and splinters must not be removed while the machine is running.

• When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.

• Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.

• Remove the battery pack before starting any work on the machine.

• Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors offer to retrieve old batteries to protect our environment.

• Do not store the battery pack together with metal objects
  (short circuit risk).

• Use only System M12 chargers for charging System M12 battery packs. Do not use battery packs from other systems.
  Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.

• Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.

• Warning! To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or al-low a fluid to fl ow inside them. Corrosive or conductive fl uids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., Can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The cordless impact wrench can be used to tighten and loosen nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been used:

• EN 62841-1:2015
• EN 62841-2-2:2014
• EN 55014-1:2017
• EN 55014-2:2015
• EN 50581:2012
• Winnenden, 2018-02-28
• Alexander Krug
• Managing Director
• Authorized to compile the technical fi le.
• Techtronic Industries GmbH
• Max-Eyth-Straße 10
• 71364 Winnenden
• Germany

The drive control button is used to adjust the rotation speed (RPM) for the application.
In Auto Shut Off Mode, the tool will drive forward at a  reduced RPM until the torque is achieved. In reverse the tool will operate at full RPM to remove fasteners at full torque.

IMPACTING TECHNIQUES

• The longer a bolt, screw, or nut is impacted, the tighter it will become.
• To help prevent damaging the fasteners or workpieces, avoid excessive impacting.
• Be particularly careful when impacting smaller fasteners because they require less impacting to reach optimum torque.
• Practice with various fasteners, noting the length of time required to reach the desired torque.
• Check the tightness with a hand-torque wrench.
• If the fasteners are too tight, reduce the impacting time.
• If they are not tight enough, increase the impacting time.
• Oil, dirt, rust or other matter on the threads or under the head of the fastener aff ects the degree of tightness.
• The torque required to loosen a fastener averages 75% to 80% of the tightening torque, depending on the condition of the contacting surfaces.
• On light gasket jobs, run each fastener down to a relatively light torque and use a hand torque wrench for fi nal tightening.

OPERATION

Note: It is recommended after fastening to always check the torque with a torque wrench.
The fastening torque is aff ected by a wide variety of factors including the following.

• State of battery charge – When the battery is discharged voltage will drop and the fastening torque will be reduced.
• Operation at speeds – Operating the tool at low speeds will cause a reduction in fastening torques.
• Fastening position – Holding the tool or the driving fastener in various angles will aff ect the torque.
• Drive accessory/socket – Failure to use the correct size accessory or socket, or a non-impact rated accessory may cause a reduction in the fastening torque.
• Use of accessories and extensions – Depending on the accessory or extension fi tment can reduce the fastening force of the impact wrench.
• Bolt/Nut – Fastening torques may differ according to the diameter of the nut or bolt, the class of nut/bolt and the length of nut/bolt.
• Condition of the fastener – Contaminated, corroded, dry or lubricated fasteners may vary the fastening torques.
• Condition and base material – The base material of the fastener and any component in between the surfaces may effect the fastening torque (Dry or lubricated base, soft or hard base, disc, seal or washer between fastener and base material).

IMPACTING TECHNIQUES

• The longer a bolt, screw, or nut is impacted, the tighter it will become.
• To help prevent damaging the fasteners or workpieces, avoid excessive impacting.
• Be particularly careful when impacting smaller fasteners because they require less impacting to reach optimum torque.
• Practice with various fasteners, noting the length of time required to reach the desired torque.
• Check the tightness with a hand-torque wrench.
• If the fasteners are too tight, reduce the impacting time.
• If they are not tight enough, increase the impacting time.
• Oil, dirt, rust or other matter on the threads or under the head of the fastener aff ects the degree of tightness.
• The torque required to loosen a fastener averages 75% to 80% of the tightening torque, depending on the condition of the contacting surfaces.
• On light gasket jobs, run each fastener down to a relatively light torque and use a hand torque wrench for final tightening.

BATTERIES

• Battery packs which have not been used for some time should be recharged before use.
• Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
• The contacts of chargers and battery packs must be kept clean.
• For an optimum life-time, after use, the battery packs have to be fully charged.
• To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
• For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and away from moisture
• Store the battery packs in a 30% – 50% charged condition Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could become to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

• The user can transport the batteries by road without further requirements.

• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
  When transporting batteries:

• Ensure that battery contact terminals are protected and insulated to prevent short circuit.

• Ensure that battery pack is secured against movement within packaging.

• Do not transport batteries that are cracked or leak. Check with forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses). If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

• CAUTION! WARNING! DANGER!

• Remove the battery pack before starting any work on the machine.

• Please read the instructions carefully before starting the machine.

• Do not dispose electric tools, batteries/rechargeable batteries together with household waste material. Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.

• n0 No-load speed

• n Impact range

• V Volts

• Direct current

• European Conformity Mark

• National mark of conformity Ukraine

• EurAsian Conformity Mark.

References

• Milwaukee Tool Europe | Cordless Power Tools, Outdoor Tools, Hand Tools, PPE, Work wear. Storage and Accessories. | Milwaukee Tools Europe
• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>