Marktrace MR6211E UHF Reader User Manual Product Information
- May 15, 2024
- Marktrace
Table of Contents
MR6211E UHF Reader
Product Information
Specifications
-
Model: MR6211E
-
Type: Serial UHF Reader
-
Version: 1.0
-
Manufacturer: Shenzhen Marktrace Co., Ltd
-
Address: Floor5/7, Block D, Changyuan New Material Port, No 2
Central 1st Hi-tech Av., Nanshan Shenzhen, P.R.C. Post518057 -
Phone: 0755-2654 6392
-
Email: technical@marktrace.com
-
Website: www.marktrace.com
Product Usage Instructions
Matters Need Attention
Make sure to read the user manual carefully before operating the
Marktrace device. For any questions or concerns, feel free to
contact us for assistance.
Reader Instruction
Reader Connection
Follow the provided instructions to correctly connect the UHF
reader to your system.
Antenna & RF Power Setting
Adjust the antenna and RF power settings as per your
requirements for optimal performance.
Frequency Setting
Set the frequency of the reader according to the desired
operating frequency.
Working Mode Setting
Select the appropriate working mode setting based on your usage
scenario.
Buzzer & LED Setting
Configure the buzzer and LED settings to suit your preferences
or operational needs.
FAQ
Q: How do I update the user manual?
A: Marktrace reserves the right to update and modify the user
manual. Check our website for any new documents as there may not be
further notice provided.
Q: What should I do if I need repair?
A: Do not attempt to repair the reader yourself by tearing up
the warranty label or disassembling the device. Contact our
Customer Service Center for assistance with warranty duties.
MR62XX Serial UHF reader user manualVer 1.0
1
MR6211E
UHF Reader User Manual
Shenzhen Marktrace Co., Ltd
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
2
FCC statements:
The device has been evaluated to meet general RF exposure requirement, The
device can be used in portable exposure condition without restriction Federal
Communication Commission (FCC) Radiation Exposure Statement Power is so low
that no RF exposure calculation is needed.
FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. NOTE: The
manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications or changes to this equipment. Such modifications or
changes could void the user’s authority to operate the equipment. NOTE: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: – Reorient or relocate the receiving antenna. –
Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help.
Federal Communication Commission (FCC) Radiation Exposure Statement When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. FCC ID:2AJQV-MR6211E
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
3
Dear Customer Many thanks for purchasing Marktrace device. Go through the user
manual carefully before you operate.
To make sure Marktrace device work correct. Any questions, please contact us.
We welcome your feedback and comments.
Shenzhen Marktrace Co.,Ltd
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
4
MR6211E UHF reader User Manual (Ver1.0)
Disclaimer
Martkrace reserve the right to update and modify this user manual. For the new
documents may has no further notice. Don’t tear up the warranty label or take
reader apart to repair by yourself, we reject perform warranty duties if this
happened.
Shenzhen Marktrace Co.,Ltd have trademark right on the trademark which in this
user manual and receive legal protection. DO NOT make free with theses
trademarks.
®
Customer Service Center
Phone400-022-3382 0755-2654 6392/2654 4205 Fax0755-2655 3743 E-mailtechnical@
marktrace.com Websitehttp://www.marktrace.com Address:Floor 3/5, Block
D,Changyuan New Material Port, No 2 Central 1st Hi-tech Av., Nanshan Shenzhen,
P.R.C. Post518057
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
5
Contents
1 MATTERS NEED ATTENTION …………………………………………7 2 READER INSTRUCTION
…………………………………………….. 8
2.1 MR6211E UHF READER INTRODUCTION …………………………………8 2.2 READER INSTRUCTION
……………………………………………… 8 2.3 READER APPLICATIONS …………………………………………….. 9 2.4 READER
MAIN FUNCTIONS …………………………………………… 9 2.5 READER TECHNICAL PARAMETER
…………………………………….. 10 3 READER STRUCTURE AND INTERFACE EXPLANATION ………………… 11
3.1 READER STRUCTURE EXPLANATION ……………………………………11 3.2 EXPLANATION ON THE
READER COMMUNICATION INTERFACE ………………….12 4 QUICK START GUIDE
……………………………………………… 14 5 READER PARAMETER CONFIGURATION …………………………….. 16 5.1
WEBPAGE CONFIGURATION …………………………………………. 16 5.2 DEMO SOFTWARE CONFIGURATION
…………………………………… 19
5.2.1 Reader connection …………………………………………… 19
5.2.2 Antenna & RF Power setting …………………………………… 19
5.2.3 Frequency Setting …………………………………………….20
5.2.4 Working Mode Setting. …………………………………………21
5.2.5 Buzzer & LED Setting ………………………………………… 21
5.2.6 IP Address Setting …………………………………………… 22
5.2.7 GPIO Setting ……………………………………………….. 22
6 DEMO SOFTWARE DEMONSTRATION ……………………………….. 23 6.1 EPC GEN2 TAG DEMONSTRATION
……………………………………. 23 6.1.1 Multi tag Identify …………………………………………….. 23
6.1.2 Multi Tag Read & Write ……………………………………….. 24
6.1.3 Tag Filter ………………………………………………….. 25
6.1.4 EPC Gen2 Tag Lock …………………………………………. 26
6.1.5 EPC Gen2 Tag Read and write with Access Password ………………. 27
6.1.6 EPC Gen2 Tag Kill. ………………………………………….. 28
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
6
6.2 ISO18000-6B PROTOCOL TAG DEMONSTRATION ………………………….28 6.2.1 ISO18000-6B tag
Identify ……………………………………… 28 6.2.2 Multi-tag user data reading ……………………………………..
29 6.2.3 Single tag data reading and read with UID ………………………… 30 6.2.4 Single
tag writing and write with UID ………………………………31 6.2.5 Single tag data lock
………………………………………….. 31 6.2.6 Single tag lock and query ……………………………………… 31
7 SECONDARY DEVELOPMENT ………………………………………. 33 8 COMMON FAULTS AND EXCLUSION
METHODS ……………………….. 34
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
7
1 Matters need attention
1 Dismantle and parts replaceMarktrace has no warranty duties on those faults
which caused by dismantle and parts replace by customer .
2 Power supplyplease use the power adaptor which alone with precuts to get
power. If not may harm the products.
3 Falling damageMind parts damage by device falling, if this happens, turn off
power immediately and connect the distributor or Marktrace customer service
center.
4 Unusual conditionAway from fire. If you find unusual odor when you use this
products, or reader on overheating or emitting smog, please power off
immediately and drop plug form the plug seat. You can connect the distributor
or Marktrace customer service center for helps. If you continue to use this
device, may cause the danger of fire or electronic shock.
5 PlaceDon’t place device on the site which is not level, mind damage or
personal injury on falling.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
8
2 Reader instruction
2.1 MR6211E UHF reader introduction
MR6211E
2.2 Reader instruction
This products has the features like multi protocol compatible, multi-tag
identify, multi-tag multi area read and write, fast reader speed, can connect
to four antennas etc. 1 Accord with ISO18000-6B and ISO18000-6C(EPC-GEN2)
standard
2 Use unique anti-collision algorithmhas the super multi-tag identify ability
3 Have tag identify function and data area read, write, lock and kill these
functions. And supply the suit API to customer to do secondary development. 4
Multi-tag identify abilityThe MAX reader range can reach 8 meters. 5 Tag
identify speed Single tag 2000 times/minute multi-tag 200pcs/second 6 Can
connect to 1 to 4 same gain and different gain planar antennas via high-
frequency cable. To expand the identify area of tag and reduce the hardware
cost for customer. The RF power of the antennas can set from 0 to 31dBm in
separate 7 Reader will detect antennas when it get power. In case to protect
antenna
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
9
port. The one has no antenna connect will not send RF power. 8 Have RS232RS485
WeigandTCP/IPRelay etc output interface 9 Compatible with tag match function
Reader can identify the tag which
match the condition or not identify these condition tags by setting the match
conditions. 10Compatible with data cache function, Using FRAM (ferroelectric
memory) which can save data when power downmemory capacity is 32KBytes Can
save 2200 pcs tag data in 12 Bytes data length.
2.3 Reader applications
This reader are widely use in various RFID systemreference application as
below 1 Logistics and warehouse Management: Goods flow, warehouse
management, and the flowing management of mail, parcel, luggage. 2 Intelligent
parking Management :Parking management and automatic
charge
3 Productive lines Management: Production process fixed Identify 4 Product
counterfeit-proof inspection: Using memory’s write-protect
functions inside tags, and identifying with true-false of products 5 Other
fields: Used widely in club management, library, student’s school,
consumption management, time management, dinner management, pool management
2.4 Reader main functions
1 Read tag dataCan read multi-tag same area and same data length in a
same time
2 Write tagCan write the same data length in multi-tag’s same area.
3 Tag matchCan read match tag or dismatch tag via setting the match
conditions
4 Make data communicate and change with the connection between
standard communication interface and controller or PC,
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
10
2.5 Reader technical parameter
1 CompatibleISO18000-6B and ISO18000-6C(EPC-GEN2) protocol standard
2 Working frequencyfixed-frequency can choose ISM 902928MHz
AmericaISM920925MHzChina ISM 865868MHzEurope Can also customer made other
frequency from ISM 900930MHz stepped frequency is 250KHz
3 Reading rangeReading from 0~10 meters (working with 7dBi antenna) 4 Tag
identify speed Single tag 2000 times/minutemulti-tag
200pcs/second 5 Trigger working modeTimer and I/O can trigger readerTimer
interval
from 10-990msI/O trigger MAX time is 255s 6 Data pre-processingOn trigger
working modeTag data can store in
cache or output directly. 7 Data cacheTrigger working mode data cache using
FRAM (ferroelectric
memory) which can save data when power downmemory capacity is 32KBytesCan save
2200 pcs tag data in 12 Bytes data length 8 Data outputData return by instant
messagingCan config RS232RS485 WeigandTCP/IPRelay interface, Can config output
data length and start addressOutput data format in ASCII 9 Compatible
ISO18000-6C tag match function match tag by setting conditions 10 For
ISO18000-6B tag. Can do read, write, lock and identify operate to
single tag one byte can read and write specific tag data with UID
11Dimensions354.00mmlength210.00mmwidth38.00mmheigth 12Working
voltageDC+9V+15V 13Working temperature-20+60 14Storage temperature-40+85
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
11
3 Reader Structure and Interface Explanation
3.1 Reader Structure Explanation
1 Reader circuit function
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
12
3.2 Explanation on the reader communication interface
1. RS232: the Reader provides standard RS232 communication interface as the
output port for data modulation. RS232 has 8 data bits format: 1 start bit and
1 stop bit, no parity bit. The default baud rate is 115200 bps. The interface
supports the reader parameters configuration, software upgrading, demo program
and all functions for series communication with development kit with functions
package
2. RJ45Ethernet Port100M EthernetTCP Server Mode; It is main mode for
connecting communication with PC also can be data output main mode The
interface supports the reader parameters configuration, software upgrading,
demo program and all functions for TCP/IP communication with development kit
with functions package
3. Data Interface DB15 diagram and pin definition
4. RS485Reader provide RS485 communication interface1011 pin
work as data main output modealso can connect with PC via serial port
use RS232-RS485 converterin this wayRS485 interface support RS232
all supported functions; 5. Programmable output interface Two sets TTL
electrical level
programmable output interface 1 2 pin works as Wiegand output interfacedefault
is high level5Vone set relay interface131415 pinrelay default status is OFF
and COM short circuit 6. Input check port2 team input check port 78 pincan
configure as trigger
read modedefault as Dangling status is high level5V
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
13
7. Power supply portDC+9V+15V==4A power port 8. Antenna port4 sets TNC
antenna port 9. Indicator light6 indicator lightincluding COM port indicator
lightpower
indicator light and 4 sets antenna indicator light
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
14
4 Quick Start Guide
1 Connect antenna to reader’s antenna portone antenna or multi-antenna
applicable, maximum 4 antennasconnect power adapter to reader and then power
onconnect reader to LAN or PC by network cable
2 In PC open demo software”MR62XX Demo V1.0″fill in reader IP address and
click”Connect”to connect reader reader factory default IP address:
192.168.1.200
3 After reader connection, it will automatically detecting antenna and
transmit power query in”Setting”page selecting detected antenna port green
icon and click”Set”button set corresponding port’s transmit power and
click”Set”buttonsee below
4 In”Gen2 EPC MultiTag” pageclick bottom right corner”Identify”button will
start EPC tag query operationsee below
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
15
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
16
5 Reader parameter configuration
5.1 Webpage configuration
Reader connect to LAN through TCP/IP portor directly connect PCin PC IE
browser input reader IP address reader factory default IP address:
192.168.1.200after running then open WEB page as below
Can be configure as below 1Basic Item configuration
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
17
1User can configure IP addressRF powerfrequencyantenna portapplied moderead
card indicating etc., 2Each antenna port RF power can be configurable, range:
0-31dBm 3Frequency standard: China FrequencyUS FrequencyEU Frequency three
type standard hopping frequency selectable 4Applied mode:”Favor speed”
and”Favor quantity” two mode selectable”Favor speed” for single tag or small
batch tags quick speed read mode “Favor quantity”for big batch tags read mode
2Operating mode configuration
1In operating mode configuration, user can configure reader to be timming
working mode or pin trigger working modetimer’s timing interval can be
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
18
configure between 10-990msWhen in trigger working mod, reading maximum lasting
time can be configure as 255s 2Read tag type can be 18000-6B or EPC G2also can
be configure read both
at same timeexpand function 3When read EPC tagread area can select as EPCTID
or USER memory 6B tag cannot select area 4User can select read tag’s start
address and read data lengthEPC tag data
use word as unit6B tag data use byte as unit; 5User filter repeat tagFilter
set one slide time windowonly new data which
not show in box can be buffer or direct output 6Read tag data can be select
buffer or directly outputdata buffer adapt with power down save ferroelectric
memorystorage capacity 32KByteswhen read data length is 12Bytescan store more
than 2200pcs tag data 3output configuration
1In working mode configure, when select data output as directly output mode,
user can configure output port
2Reader data output port have RS232RS485WiegandEthernet and relay
output
3Wiegand protocol support Wiegand26 and Wiegand34
4Relay close delay time configurable between 0-99s
5For above mentioned port, user can select one type or multiple type to
output data
6Data output as ASCII code formatdata format see below
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
19
All above configuration will be valid only after click left bottom button”set”
button
5.2 Demo software Configuration 5.2.1 Reader connection
Click MR62XXDemo.exe software, input reader’s IP into the IP input box
(Default IP: 192.168.1.200, Port: 100 which is fixed), then click `connect’
ICON, software information display box will display the reader’s parameter on
the success connection. Below image demonstrate the success connection.
5.2.2 Antenna & RF Power setting
1 On MR62XXDemo.exe software’s Setting interface, query and set Antenna’s RF
Power on Power setting; Query and set Antenna on Antennas Setting. Take below
image for the reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
20
2Set the 4 antenna ports RF power separately from the range of 0 to 31dBm. 3On
the reader connection, the antenna port will begin self detection, and the
connecting Antenna port is on GREEN ICON, Disconnecting Antenna port is on RED
ICON. Only the selected GREEN ICON port’s antenna works. 2 On Integrated RFID
reader and Desktop RFID reader, config and set one
antenna port for the reader to work.
5.2.3 Frequency Setting
On MR62XXDemo.exe software’s Setting interface, Query Reader’s Frequency on
Frequency setting menu, there are China Frequence (920-925MHz), North America
Frequency (902-928MHz), European frequency (865-868MHz), and others frequency
configurable. China, North America, and European Frequency type are in FHSS
working mode. Select Fixed frequency or multi fixed frequency working mode on
the others frequency type, take below images for the reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
21
5.2.4 Working Mode Setting.
1On setting interface’s Working Mode Setting, there are two working mode,
Favor speed and Favor quantity for the query and setting, take below image for
the reference.
2Favor speed is for single tag or few tags reading with the high speed tag
reading rate. Favor Speed working mode is configurated for the applications
require high speed tag reading rate (e.g. Not-stop Highway toll) Favor
Quantity is for the multi and tense tags reading, Favor Speed working mode is
configurated for the applications (e.g. warehouse, logistic) 3If the reader is
configurated into Favor speed working mode, it’s invalid for the Matched EPC
tag reading.
5.2.5 Buzzer & LED Setting
1On Setting interface’s Buzzer & LED Setting menu for Querying and Setting
Buzzer & LED ON/OFF. Take below image for the reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
22
2After setting Buzzer & LED ON/OFF, Reader automatically reset, and need to
reconnect the reader.
5.2.6 IP Address Setting
1On setting interface’s TCP Parameter Setting menu for querying and setting
reader’s IP, take below image for the reference.
2 Reader automatically reset when set a new IP address, and need to reconnect
the reader with new IP address
5.2.7 GPIO Setting
On Setting interface’s Set Out Port menu for the reader output port setting.
The reader has two sets output port and one set Relay port. IO Port0 and IO
Port1 are output port with default High level voltage (5V) and Low level
voltage (0V) configurable. IO port2 is Relay output port with default OFF
setting. take below image for the reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
23
6 Demo software demonstration
6.1 EPC Gen2 tag Demonstration 6.1.1 Multi tag Identify
1On Gen2 EPC Multi Tag interface’s Identify menu for the Multi tag identify,
and click Identify ICON to start the reading. EPC code, antenna number and tag
reading times displayed on the interface info. box. On the interface bottom
displays tag number, Peak reading rate, Read times, total reads, Average
reading rate, and duration reading time. Take below image for the reference.
2Click Stop’ ICON for stopping tag identify. 3Click Once’ ICON for sending
once tag detect command, and returns the tag number, take below image for the
reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
24
6.1.2 Multi Tag Read & Write
1On Gen2 EPC Multi Tag interface’s Multi Tag Read menu for the Multi tag read,
Multi tag reader is read tag’s RESERVE Membank, EPC Membank, TID Membank &
USER Membank at the same time. The steps are: 1) select the reading Membanks,
2) select the start reading address and the reading word count (EPC tag’s unit
is word), and then click `Read’ ICON to start the Multi-tag reading. Take
below image for the reference.
2 Click `Stop’ ICON to stop Multi-tag reading, at the bottom of the demo
software interface display the tag number, and the reading duration time.
3 On Gen2 EPC Multi Tag interface’s Multi Tag Write menu for Multi tag
encoding. Multi-Tag Write is to encode the tag’s Reserve Membank, EPC
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
25
Membank, and USER Membank at the same time. The steps are: 1) select the encoding Membank, 2) select the tag start encoding address and the encoding word count (EPC tag’s unit is word), 3) input the encoding value, then click `Write’ ICON to encoding the multi-tag. Take below image for the reference.
4Click `Stop’ ICON to stop the Multi-Tag encoding, at the bottom of the demo
software display the Success encoding tag number, and tag encoding duration
time. 5In accordance with the EPC Protocol, On Multi Tag Read & Multi Tag
Write, EPC Membank’s Start reading address and Start encoding address is from
the EPC Membank’s Second word address.
6.1.3 Tag Filter
On Gen2 EPC Single Tag interface’s Gen2 Select Config menu for the Tag Filter
rule setting. Tag Filter setting rule is based on the EPC Membank, TID Membank
or USER Membank value for the setting condition. In accordance
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
26
with the EPC Gen2 Protocol, RESERVE Membank’s data is invalid for the tag filter rule setting. Please 1) select the EPC tag Membank, 2) the word addr. 3) Word Length, 4) Input the value, then Click `Config’ ICON for the Tag filter rule setting. 1Only on Favor quantity working mode, the Tag filter setting is valid, on Favor speed working mode, tag filter setting is invalid. 2Match setting, reader reads and displays only the condition matched tag. 3Mismatch setting, Reader doesn’t read and display the condition matched tag.
4Empty the input value for cancel the Tag filter rule.
5If setting EPC Membank as the Tag filter rule, the valid Word Addr is 2.
6After set the EPC tag filter rule, this rule is valid for all EPC tag detect.
7After set the EPC tag filter rule, this rule is valid for all the time unless
the reader is power off or reset.
6.1.4 EPC Gen2 Tag Lock
1On Gen2 EPC Single Tag interface’s Gen2 Secured Lock menu for the EPC Gen2
Tag Lock setting. With Access Password, it can lock Reserve Membank, EPC
Membank, and USER Membank in different lock level. Take below image for the
reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
27
2EPC Gen2 Tag Lock level are unlock, unlock forever, and secure lock, lock
forever 1Unlock means the tag is not to encrypted the tag 2Unlock forever
means the tag will not be locked forever 3 On Secure Lock, RESERVE Membank
only can be read and write with
Access Password, EPC Memban and USER Membank can be encoded with Access
Password. 4Lock forever, if the tag is set to lock forever, it can’t be unlock
again.
6.1.5 EPC Gen2 Tag Read and write with Access Password
1n Gen2 EPC Single Tag interface’s Gen2 Secured Read and Gen2 Secured Write
menu for the EPC tag reader and write with Access password. Take below image
for the reference. 1Gen2 Secured Read with Access password
2Gen2 Secured Write with Access password.
2EPC Gen2 Secured Read with Access password need to input the Select Read
tag’s Word Addr, and the WordCnt. 3EPC Gen2 Secured Write with Access password
need to input the Select
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
28
Write tag’s Word Addr, and the WordCnt 4 Secure locked Reserve Membank can
only be read & write with Access Password, Secure Locked EPC Membank and
Secure Locked USER Membank can be encoded with Access Password, while can read
without the Access Password. 5 In accordance with the EPC Protocol, TID
Membank can’t be locked, Access Password is invalid for TID Membank.
6.1.6 EPC Gen2 Tag Kill.
1 On Gen2 EPC Single Tag interface’s Gen2 Kill menu for the Tag Kill password
to kill the tag, Take below image for the reference.
2EPC Gen2 tag can’t be read and write if the tag is killed.
6.2 ISO18000-6B Protocol tag Demonstration 6.2.1 ISO18000-6B tag Identify
On ISO 6B interface for the ISO18000-6B tag Identify. Click Identify’ ICON for the tags Identify, and the software interface displays the ISO18000-6B tag’s UID code, Antenna No., and the read times. ClickStop’ ICON for stoping
the tag Identify. Take below image for the reference.
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
29
6.2.2 Multi-tag user data reading
Put several 6B tags in the radiation range of antenna in the ISO 6B operation
interfacechoose Multi Tag Read to enter into multi-tag data reading interface
choose the start address of data that you want to read,then click”Read”button
to operate multi-tag data readingthe interface will indicate 8 bytes data from
start addressantennas numbers and times to be readlike following picture
indicatesclick”Stop”button to stop user data reading
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
30
6.2.3 Single tag data reading and read with UID
1In the ISO 6B operation interfacechoose Single Tag to enter into single tag
operation interfacechoose the start address of data you want to read in the
ISO Read menu item click”Read”button to start reading data the interface will
indicate the tags data that is readthe data length is 8 bytes data from start
address
2When data read with UIDit needs to know the UID of the tag firstyou can set
the start address to 0 when query UIDthe reading data is tag UIDafter
inputting UIDchoose the start address of reading dataclick”Read With
UID”button to operate data reading
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
31
6.2.4 Single tag writing and write with UID
1Single Tag operation interfacechoose the data address you want to write in
the ISO Write menu itemclick”Write”button to write data
2When operate writing data with UIDexcept for inputting the single byte data
that needs to writeit also needs to put the UID number of tagchoose the start
address that want to writeclick”Write With UID”button to write data
6.2.5 Single tag data lock
1Single Tag operation interfacechoose the data address you want to lock in the
ISO Lock menu itemclick”Lock”button to lock dataif return “ISO Lock tag
success” in “Result”column,it means lock successfully
2It is unable to rewrite data in the address that is successfully locked
6.2.6 Single tag lock and query
Single Tag operation interfacechoose the data address you want to query in the
ISO Query Lock menu itemclick “Query”button to lock and queryit will
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
32
return query result in “Result” columnlike”Had locked”and”Not lock”
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
33
7 Secondary development
User can make secondary development for reader application software if
needing. We provide SDKwhich supports VC++C#JAVA and so onthe use of
SDK,please refer toMR62XX serial reader SDK instruction
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
MR62XX Serial UHF reader user manualVer 1.0
34
8 Common faults and exclusion methods
Failure Description
Unable to start reader
Unable to connect reader Reader is unable to identify tag No sound when
reading tag
Tag with password operation failed
Invalid tag filter settings Unable to refresh the page in the web
configuration
Simple exclusion methods make sure the power adapter indicator light is on
make sure the reader power interface is connected well make sure the reader IP
address is correct make sure the network environment is good make sure antenna
ports are connected correctly make sure antenna power is not to be 0
make sure the buzzer is open
make sure that when tag operates with password,the radiation range of antenna
is single tag or small amount of tags
make sure the reading mode for reader is multi-tag read
Clear CGI in the web address or re-enter the IP address of the reader and
refresh
Address Floor5/7, Block D,Changyuan New Material Port, No 2 Central 1st Hi-
tech Av., Nanshan Shenzhen, P.
R.C. Post518057 Phone0755-2654 6392 FAX0755-2655 3743
E-mailtechnical@marktrace.com Websitewww.marktrace.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>