SIHOO V1-M109 Ergonomic Office Chair Installation Guide
- May 15, 2024
- SIHOO
Table of Contents
SIHOO V1-M109 Ergonomic Office Chair
PRODUCT INSTALLATION GUIDE
Hello Friend,
Thank you for choosing SIHOO office chair.
If you need an installation video ,you can go to our official website
sihoooffice.com.
The chair comes with product warranty service. If there is any problem with
the chair, please contact our after-sales service department on SIHOO store
immediately, and believe that they will provide you with a satisfactory
solution. If the chair meets your needs, welcome to share your feelings.
Please feel free to contact us via the following email:
service@sihoooffice.com
Thank you for being one of our customers. We love our customers, if you need us, we will always be here.
CAUTION !
Work on gas springs only by trained specialist personnel.
Assembly Instruction The size will be according to regular measurements）
| | |
---|---|---|---
Screw the castors
into the legs.| Put the gas lift into
the center of the
base.| Connect the seat and
footrest with four M620 screws. 2 3| Connect the mechanism and seat with four
M625 screws with small spacers.
| | |
Use three M8*40screws and spring lamination and small shims to connect the the
seat cushion to the backrest| Put the upper part of the assembled chair into
the gas lift.| Insert the armrest into seat cushion, use the armrest knobs and
big shims to install the armrest on the seat cushion.| Insert the backrest
into the slot.
Functions The size will be according to regular practice）
Installation Safety Guideline
- Please read through assembly instruction and parts list before any installation.
- Please check if there are missing parts or any damages.
- Please put on the protection gloves to avoid any injury when installing.
- Please choose a spacious and clean place and cover a paperboard on the floor to avoid any friction damage when proceeding the instillation.
- Please fasten all the screws and shims into the installation positions tightly according to the Assembly Instruction.
- Please be aware that the gas lift would be difficult to remove once installed. If the chair is needed to be removed, firstly, you can apply a rubber hammer to remove it by tapping the gas lift head a few times; then you may take out the chair base. Secondly, tap on the five legs to loosen the gas lift from the base. Please be careful during the operation. (Disclaimers: customers will be responsible for any damage or injury caused by misconduct of installation, please be careful.)
Precautions for use
- The product was designed for one person only, please do not be seated more than one person.
- You shall refer to the functions instruction when you are using the product.
- The product can only be seated when all the screws and parts are fastened. All parts should be checked on every three months routinely to make sure no loose.
- Please use the product on the flat floor. Away from humid enviroment, any fire hazards and direct sunlight.
- Children under 5 shall be accompanied by adults when using the product.
- Please do not stand on the chair or use it as a ladder or footsteps.
- Please do not sit on the armrests in case of causing any danger.
- Please use a soft cloth to clean up the dust on the product before usage. Do not use rough cloth to wipe the product.
- For your own safety, please do not uninstall the gaslift.
Parts List
（The size will be according to regular measurements; Screws and shims with one more as a backup)
| | |
---|---|---|---
Seat cushion1pc| Backrest1pc| Armrests1pair| Headrest1pc
| | |
Base1pc| Footrest1pc| Mechanism1pc| Armrest knob2pcs
| 
| |
Wrench1pc| Spring lamination3+1pcs| Backrest screw(M840)3+1pcs| Gas
lift1pc
| | |
Castor5pcs| Footrest screw(M620)4+1pcs| | Mechanism screws(M625)4+1pcs
Note: Please separate the screws by size before assembly for easy installation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>