SIHOO V1-M101 Ergonomic Office Chair with 4D Arms 2 Way Lumbar Support User Manual
- June 15, 2024
- SIHOO
Table of Contents
SIHOO V1-M101 Ergonomic Office Chair with 4D Arms 2 Way Lumbar Support
Thank you!
Hello Friend,
Thank you for choosing SIHOO office chair.
If you need an installation video ,you can go to our official website sihoooffice.com.
The chair comes with product warranty service. If there is any problem with the chair, please contact our after-sales service department on SIHOO store immediately, and believe that they will provide you with a satisfactory solution. If the chair meets your needs, welcome to share your feelings.
Please feel free to contact us via the following email: service@sihoooffice.com
Thank you for being one of our customers. We love our customers, if you need us, we will always be here.
Assembly Instruction
(The size will be according to regular measurements)
| | |
---|---|---|---
1. Screw the castors into the legs.| 2. Put the gaslift into the center of
the base.| 3. Connect the mechanism and seat cushion with 4 M625 screws and
small spacers| 4. Use three M840 screws and spring lamination and small
shims to connect the seat cushion to the backrest.
| | |
5. Put the upper part of the assembled chair into the gaslift.| 6. Insert
the armrest into seat cushion, use the armrest knobs and big shims to install
the armrest on the seat cushion.| 7. Insert the backrest into the slot.|
Functions
(The size will be according to regular practice)
Installation Safety Guideline
- Please read through assembly instruction and parts list before any installation.
- Please check if there are missing parts or any damages.
- Please put on the protection gloves to avoid any injury when installing.
- Please choose a spacious and clean place and cover a paperboard on the floor to avoid any friction damage when proceeding the installation.
- Please fasten all the screws and shims into the installation positions tightly according to the Assembly Instruction.
- Please be aware that the gaslift would be difficult to remove once installed.
If the chair is needed to be removed, firstly, you can apply a rubber hammer to remove it by tapping the gaslift head a few times; then you may take out the chair base. Secondly, tap on the five legs to loosen the gaslift from the base. Please be careful during the operation.
(Disclaimers: customers will be responsible for any damage or injury caused by misconduct of installation, please be careful.)
Precautions for use
- The product was designed for one person only, please do not be seated more than one person.
- You shall refer to the functions instruction when you are using the product.
- The product can only be seated when all the screws and parts are fastened. All parts should be checked on every three months routinely to make sure no loose.
- Please use the product on the flat floor. Away from humid environment, any fire hazards and direct sunlight.
- Children under 5 shall be accompanied by adults when using the product.
- Please do not stand on the chair or use it as a ladder or footsteps.
- Please do not sit on the armrests in case of causing any danger.
- Please use a soft cloth to clean up the dust on the product before usage. Do not use rough cloth to wipe the product.
- For your own safety, please do not uninstall the gaslift.
Parts List
(The size will be according to regular measurements; Screws and shims with one more as a backup)
| | |
---|---|---|---
Seat cushion*1pc
|
Backrest*1pc
|
Armrests*1pair
|
Headrest*1pc
| | |
Base*1pc
|
Armrest knob*2pcs
|
Mechanism*1pc
|
Big shims*2pcs
| | |
Wrench*1pc
|
Small shims*7+1pcs
|
Backrest screw(M840)3+1pcs
|
Gaslift*1pc
| |
Castor5pcs| Spring lamination3+1pcs|
Mechanism screws(M625)4+1pcs
Note: Please separate the screws by size before assembly for easy installation.
Planckstr. 59 / 45147 Essen
Tel: +49 1726894470 /
Email: Ec-connection@web.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>