KYX P2i Series 2 Hitch Mounted E-Bike Rack Instruction Manual
- May 15, 2024
- KYX
Table of Contents
E-BIKE CAR RACKS
INSTRUCTIONAL MANUAL
P2i Series
P2i Series 2 Hitch Mounted E-Bike Rack
Package Content
1. Parts Included
2. Schematic diagram of the overall assembly
3. Screws and other accessories
Warning
- This package contains small items that may pose a choking hazard if swallowed. Please keep them away from young children.
- Be sure to read and fully understand these instructions before attempting to install them. If you are unsure about any part of this installation, ask a professional installer for help
- Use the right tools. Improper installation may result in property damage or other serious injuries.
- Do not use on trailer or rv
- Must follow instruction manual
Installation Steps
Step 1: Install the Cross Bar
- Flip the controller
- Insert one side of the Cross Bar into the controller and align the Cross Bar with the fixing hole of the controller
- Put the M10 Spring Washer and M10 Flat Washer on the M10*25mm Bolts, insert them into the controller and the fixing hole of the Cross Bar, and tighten all the bolts with a wrench
- Repeat and install the other Cross Bar
Step 2: Install the Vertical Bar
- The M10 Nylon Washer has been pre-installed on the controller. Check whether the M10 Nylon Washer is securely installed
- Insert the Vertical Bar into the controller(As shown in the Image 1
- Align the controller and the fixing hole of Vertical Bar, insert the M10*71mm Bolt through the controller and the fixing hole of Vertical Bar, put the M10 Flat Washer and M10 Self-locking Nut on the tail of the bolts, and tighten them with a wrench.
Step 3: Connect the controller to the base
- The M10 Nylon Washer is pre-installed on the base. Check whether the M10 Nylon Washer is securely installed
- Insert the Part A into the positioning hole of the base, pass the M10*103mm bolts through the fixing holes on the base and controller. put the M10 Flat Washer and M10 Self-locking Nut on the bolt tail in turn, and tighten the bolts with a wrench until the controller does not wobble from side to side in the base
Step 4: Install the Footrest and Pressure Bar
Open the Speed Handle of the Footrest and install them in sequence:
- Pass through the left Cross Bar
- Pass through the right Cross Bar
- Pass through the left Cross Bar.
- Pass through the right Cross Bar
Step 5 Attach the E-Bike Car Rack to the car
- Insert the base connection section into the car hitches and align the base with the fixing holes of hitches
- Put the M12 Spring Washer and M12 Flat Washer on the M12°100mm Bolt and tighten them with a wrench untile the rack is completely secure
- Put a lock on the tail of the bolt to lock the E-Bike Car Rack in case it’s stolen
Step 6:
Place the E-BIKE or bicycle on the E-Bike Car Rack, open the Speed Handle of
the Pressure Bar, pass through the Vertical Bar as shown in the image, firrnly
press the Pressure Bar to the vehicle, and fasten the Speed Handle to lock the
vehicle
Step 7:
Attach the Velcro strap securely to each tire, and then the installation is
done.
Well Note: E bike rack has a bit different installation steps with metal
and aluminum version but not effect installation.
https://www.amazon.com/live/video/0f2f31339b514470b891fe77bd942c6f?ref_=asvh_vdp
It’s my pleasure to serve you. Have a good time!
Note: Please contact us when you receive the defective products or when you have any question or advice.
support@kyxauto.com
www.kyxauto.com
After Sales Service: +1 (833) 495 – 0884
Work Time: Monday – Friday, 9 a.m. – 5 p.m.
Documents / Resources
| KYX
P2i Series 2 Hitch Mounted E-Bike
Rack
[pdf] Instruction Manual
P2i Series, P2i Series 2 Hitch Mounted E-Bike Rack, 2 Hitch Mounted E-Bike
Rack, E-Bike Rack, Rack
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>