KYX P2a Series E Bike Car Racks Instruction Manual

June 17, 2024
KYX

KYX P2a Series E Bike Car Racks
KYX P2a Series E Bike Car Racks

Note

Before installation: If you have any questions about the installation, please take photos and contact us, and please read this instruction carefully. Proper tools will improve installation quality and shorten the time required.
Customer service mail: SUPPORT@KYXAUTO.COM

Package Content

  1. Parts Included
    Package Content

  2. Schematic diagram of the overall assembly
    Package Content

  3. Screws and other accessories
    Package Content

Warning

  1. This package contains small items that may pose a choking hazard if swallowed. Please keep them away from young children.
  2. Be sure to read and fully understand these instructions before attempting to install them. If you are unsure about any part of this installation, ask a professional installer for help
  3. Use the right tools. Improper installation may result in property damage or other serious injuries
  4. MUST FOLLOW INSTRUCTION MANUAL
  5. Check the joint parts every three months to ensure that screws are not loose

Installation Steps

Step 1: Install the Cross Bar

  1. Insert the Cross Bar into the Controller in the direction shown
  2. Insert the M10*103mm bolts into the fixing holes, install the M10 flat washers and M10 self-locking nuts to the ends of the bolts, and tighten them using a wrench,
  3. Repeat and install the other cross bar
  4. Rollover the controller
  5. Insert M10 spring washers and M10 flat washers onto the M10*35mm bolts, align them with the fixing holes, and tighten them using a wrench

Step 2: Install the Vertical Bar

Installation Steps

  1. The M10 Nylon Washer has been pre-installed on the controller. Check whether the MIO Nylon Washer is securely installed
  2. Insert the Vertical Bar into the controller(As shown in the Image 1)
  3. Insert the M1077mm bolts into the fixing holes, install the M10 flat washers M1035flat washer- sand M10 self-locking nuts to the ends of the bolts, and tighten them using a wrench.

Step 3: Connect the controller to the base

Installation Steps

  1. The M10 Nylon Washer is pre-installed on the base. Check whether the M10 Nylon Washer is securely installed
  2. Insert the Part A into the positioning hole of the base, pass the M10103mm bolts through the fixing holes on the base and controller, put the M10 Flat Washer and M10 Self-locking Nut on the bolt tail in turn, and tighten the bolts with a wrench until the controller does not wobble from side to side in the base

Step 4: Install the Footrest and Pressure Bar

Installation Steps

Open the Speed Handle of the Footrest and install them in sequence.

  1. Pass through the left Cross Bar
  2. Pass through the right Cross Bar
  3. Pass through the left Cross Bar,
  4. Pass through the right Cross Bar

Step 5 Attach the E-Bike Car Rack to the car

Installation Steps

  1. Insert the base connection section into the car hitches and align the base with the fixing holes of hitches
  2. Insert the M12*100MM Bolt and tighten them with a wrench until the rack is completely secure
  3. Put a lock on the tail of the bolt to lock the E-Bike Car Rack

Step 6:

Installation Steps

Place the E-BIKE or bicycle on the E-Bike Car Rack, open the Speed Handle of the Pressure Bar, pass through the Vertical Bar as shown in the image, firmly press the Pressure Bar to the vehicle, and fasten the Speed Handle to lock the vehicle

Step 7:

Installation Steps

Attach the Velcro strap securely to each tire

Customer Support

Note: Please contact us when you receive the defective products or when you have any question or advice.

support@kyxauto.com
www.kyxauto.com

It’s my pleasure to serve you. Have a good time!

Documents / Resources

| KYX P2a Series E Bike Car Racks [pdf] Instruction Manual
P2a Series E Bike Car Racks, P2a Series, E Bike Car Racks, Bike Car Racks, Car Racks
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals