TAC-UTC-002 Universal Bed Tire Carrier Instruction Manual
- May 15, 2024
- TAC
Table of Contents
TAC-UTC-002 Universal Bed Tire Carrier
Specifications
- Product Name: Universal Bed Tire Carrier
- Part Number: TAC-UTC-002
- Website: www.tacautoparts.com
Product Usage Instructions
Parts List:
- 1 Bed Tire Carrier
- 4 12mm x 45mm T-Bolts
- 4 12mm x 32mm OD x 3mm Flat Washers
- 4 12mm Lock Washers
- 4 12mm Hex Nuts
- 8 12mm Plastic Retainers
- 4 12mm Fish Wires
Installation Procedure
- Start by placing the Bed Tire Carrier in the desired location on the bed floor of the vehicle.
- Mark the drilling locations carefully, ensuring to drill pilot holes and use a 1/2inch drill bit for the T-Bolts.
- Thread the T-Bolts with Fish Wires and Plastic Retainers for aluminum bodies to prevent corrosion.
- Secure the Bed Tire Carrier with Flat Washers, Lock Washers, and Hex Nuts. Do not fully tighten at this stage.
- Adjust and level the carrier before fully tightening all hardware.
- Place the tire onto the carrier and attach strap hooks for secure fitting.
- Regularly inspect the installation to ensure all hardware is secure and tight.
Cleaning Instructions:
To clean the Tire Carrier, avoid using polish or wax with abrasives that could damage the finish. Mild soap can be used for cleaning.
FAQ
Q: Are straps included with the Bed Tire Carrier?
A: No, straps are not included. We recommend purchasing a 3-point strap for a secure fit.
Q: How often should I inspect the installation?
A: It is recommended to do periodic inspections to ensure all hardware is secure and tight.
UNIVERSAL BED TIRE CARRIER
PART#TAC-UTC-002
Parts List
| 1 | Bed Tire Carrier | 4 | 12mm Hex Nuts |
|---|---|---|---|
| 4 | 12mm x 45mm T-Bolts | 8 | 12mm Plastic Retainers |
| 4 | 12mm x 32mm OD x 3mm Flat Washers | 4 | 12mm Fish Wires |
| 4 | 12mm Lock Washers |
PROCEDURE
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING IS REQUIRED.
-
Start installation in the bed of the vehicle the Bed Tire Carrier will be installed to. Place the Tire Carrier onto the bed floor in the desired location. Place tape underneath the desired slots and mark the slots for drilling, (Figure 1). NOTE: For corrugated beds. Only mark drill holes in the center of highest point of the corrugation as to not bend the metal.
-
Drill a pilot hole into the marked locations, (Figure 2 left hole). Use a 1/2inch drill bit to clear the 12mm
T- Bolts, (Figure 2 right hole). -
Select (1) 12mm T-Bolt and (1) 12mm Fish Wire. Thread the Fish Wire onto the T-Bolt and guide the T-Bolt into the newly drilled hole, (Figure 3). Thread (1) 12mm Plastic Retainer onto the T-Bolt to hole it in place, (Figure 4). IMPORTANT: For aluminum vehicle bodies, it is necessary to thread (1) 12mm Plastic Retainer onto the 12mmT-Bolts before being inserted into the bed to prevent corrosion. Repeat this Step for the remaining (3) 12mm T-Bolts.
-
Place the Bed Tire Carrier onto the (4) T-Bolts and secure with (4) 12mm Flat Washers, (4) 12mm Lock Washers and (4) 12mm Hex Nuts, (Figures 5 & 6). Do not tighten hardware.
-
Adjust and level the Bed Tired Carrier, then fully tighten all hardware.
-
Place the tire into the Bed Tire Carrier. Determine the locations to attach the strap hooks, (Figures 7—9). (Straps not included, 3-point strap recommended purchase). For a more secure fit, use the side hoops on the Tire Carrier to strap down the tire crossways, (Figure 7).
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Tire Carrier.
Passenger/Right Installation Pictured
NOTE: For corrugated beds. Only mark drill holes in the center of highest point of the corrugation.
-
(Fig 1) Place the Bed Tire Carrier onto the desired location on the floor of the bed. Place tape onto the bed under slots. Mark locations for drilling. IMPORTANT: Check underneath the bed to avoid drilling through gas lines or other important fixtures under the bed.
-
(Fig 2) First drill a pilot hole into the marked location, then use a 1/2inch drill bit to clear the 12mm T-Bolts
NOTE: For aluminum vehicle bodies, it is necessary to thread (1) 12mm Plastic Retainer onto the 12mmT-Bolts before being inserted into the bed -
(Fig 3) Thread (1) 12mm T-Bolt into (1) 12mm Fish Wire. Slide the end of the Fish Wire into the drilled-out hole from the bottom of the bed
-
-
(Fig 4) Thread (1) 12mm Plastic Retainer to the T-Bolt to hold it in place
-
(Fig 5) Attach the Bed Tire Carrier to the T-Bolts
-
(Fig 6) Bed Tire Carrier attached to the bed floor
- (Fig 7) Determine the strap attachment points, (straps not included). If desired, use a strap crossways from the sides of Carrier (not shown)
- (Fig 8) Secure the strap hook to the lower hoop (strap not included)
- (Fig 9) For 3-Point straps, (recommended separate purchase). Attach the hooks to either the upper hoops or inner plates as shown in picture above
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>