SEALEY TS01.V2 Vice Bench Mounting Sheet Metal Folder Instruction Manual

SEALEY TS01.V2 Vice Bench Mounting Sheet Metal Folder

Specifications:

• Model: TS01.V2
• Length: 700mm

Product Information

Introduction:
This VICE/BENCH MOUNTING SHEET METAL FOLDER is designed to assist in folding sheet metal with precision and ease. It comes with various features to ensure efficient operation and high-quality results.

Features:

1. Top/Base plate clamp
2. Adjustment/Positioning Cam
3. Removable Folding Plate
4. Centre adjustment nut
5. Top Plate
6. Footplate with fixing holes
7. Folding Handles

Operation:

1. Unpack the unit and check for any damage or missing parts.
2. Position the folder on a bench for mounting, ensuring proper alignment of handles.
3. Adjust the top plate using the center adjustment nut to create a slight bow in the middle.
4. Release clamps to insert a test piece of sheet metal between the top and base plates.
5. Adjust the top plate alignment using clamps and a spanner.
6. Create a fold by raising the top folding plate using the handles.
7. Proceed with folding the actual workpiece based on test results.
8. To fold longer lengths of metal sheet, rotate the end clamp through the vertical axis as needed.

FAQ:

• Q: What safety precautions should I take while operating the sheet metal folder?
  A: It is essential to wear approved safety goggles, gloves, and non-slip footwear. Ensure good footing, avoid operating under the influence, and keep unqualified persons, especially children, away from the tool.

• Q: How should I dispose of the product when it becomes unserviceable?
  A: Recycle unwanted materials and sort all parts for disposal at a recycling center. Drain any fluids into approved containers before disposing of the product according to local regulations.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Wear approved safety goggles, gloves, and footwear, when operating the folder. Your local Sealey dealer offers a complete range of safety equipment.
• Use the tool only for its intended purpose.
• Regularly check all parts of the folder for damaged parts. DO NOT use if any of its components are broken, worn or damaged.
• Use original Sealey spare parts and accessories. Use of non-recommended spare parts may be dangerous and will invalidate the warranty.
• Ensure good footing, wear non-slip footwear.
• DO NOT operate this tool while under the influence of drugs, alcohol or other impairing medication.
• DO NOT Allow unqualified persons to operate the metal folder. Keep children away from the tool.

INTRODUCTION

Bench and vice mounting sheet metal folder, fitted with mounting plates. Capable of bending up to and beyond a 90° angle. The unique patented endless design and removable folding plate allows the user to fold, channel, and offset any length of sheet metal up to 20 gauge thick, by simply moving the sheet as required after each fold. With an adjustable fold plate to help achieve the cleanest fold possible. Ideal for small garages or restoration operations.

SPECIFICATION

• Model No: …………………………………………………TS01.V2
• Capacity: …………700mm x 20 Gauge Sheet, Ø1mm Rod

FEATURES

1. Top/Base plate clamp
2. Adjustment/Positioning Cam
3. Removable Folding Plate
4. Centre adjustment nut
5. Top Plate
6. Footplate with fixing holes
7. Folding Handles

OPERATION

• Unpack the unit and check that all parts are included and not damaged. Should you experience a problem contact your supplier immediately.
• Position the folder on the bench where it is to be mounted, ensuring that the handles (fig.1.7) hang vertically over the front of the bench. Use foot plates (fig.1.6) as templates to drill holes in the bench. Use appropriate fixings, or clamp folder in a vice.
• By using the center adjustment nut (fig.1.4) ensure the top plate is slightly bowed in the middle. Then use the clamps to bring to parallel under pressure. This may require adjustment from time to time.
• Release clamps (fig.1.1) at either end of a folder so that a small test piece of sheet metal can be inserted between the top and base plates. (fig.1.3)
• Position the test piece, adjust the top plate by use of clamps ( fig.1.1) lightly tighten, and use a spanner to adjust the cam (fig1.2), so that the base and top plate are aligned.
• Ensure that there is even pressure on both ends.
• Raise the top folding plate (fig.1.3) by lifting handles to create the fold. From this test, you will be able to determine how and where the fold appears.
• When satisfied with the test results, proceed with the actual workpiece.
• By rotating the end clamps through the vertical axis, longer lengths of metal sheets can be folded, i.e. fold a section, unclamp, move the sheet, reclamp, fold a second section, etc.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note : It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.
Important : No Liability is accepted for incorrect use of this product.
Warranty : The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
© Jack Sealey Limited

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>