Antennas ECLDUO2A Indoor HDTV Antenna Instruction Manual
- May 15, 2024
- Antennas
Table of Contents
Antennas ECLDUO2A Indoor HDTV Antenna
READ BEFORE INSTALLATION
Before attaching the antenna to any surface, TEST RECEPTION in that area. Connect the antenna to the 1V or converter box and run a full channel scan. If reception is not as desired, move the antenna and rescan for the available channels.
The ClearStream ECLIPSE 2 comes with:
- ClearStream ECLIPSE 2 Antenna
- Hook& Loop Tabs and Push Pins
- 12 ft. Coaxial Cable
- Jolt Switch 18dB In-Line Amplifier with Coaxial Cable and 6 ft. USB Cable
SET UP THE ANTENNA
Attach the antenna to a wall or non-metallic surface using the included push- pins in the small holes at the top and bottom of the antenna, or on a window using the hook & loop tabs. Clean any surface and allow to air-dry before using the hook & loop tabs. The adhesive is strong – please take care when removing.
The Jolt Switch gives you control in real time when managing your TV signals. The simple ON/OFF switch allows you to bypass amplification when a TV channel doesn’t need it. The amplifier arrives in the ON position, increasing TV signals for a clearer picture and sound. When the switch is OFF, easily bypass the amplifier while signals are still being filtered from cellular and FM interference.
Certain TV signals may be strong enough that an amplifier is not necessary. If
a channel is distorted or pixelated when the amplifier is ON, it may be over-
amplified. Toggle the switch to the OFF position. You do not need to rescan
your TV for channels unless you reposition or reconnect your antenna
.
Make sure the antenna is facing the broadcast towers.
NOTE: You must use the 12 ft Coaxial Cable (3) between the antenna and
the amplifier. You cannot attach the male connector on the amplifier’s coaxial
cable to the antenna or the antenna and amplifier will not work.
Now that you’ve installed your antenna, you are ready to scan for channels. See “Scanning for channels” in the troubleshooting guide. Congratulations! You’re watching HDTV for FREE! Welcome to the Antennas Direct cord-cutting family.
TROUBLESHOOTING
Problem: I’m not getting any signals at all.
Possible causes:
- Analog-only televisions (manufactured before 2007) require a digital converter box. You MUST perform a channel scan on the converter box.
- SCANNING FOR CHANNELS: A digital 1V must be programmed in order to receive digital channels. Once your antenna is installed, you must complete a channel scan, even if you have done so before installing to find the best location for the antenna.
- a) YourlV must be set to the proper input source. Press the “Input” (or “Source” ) button on your remote and make sure the input is set to lV.
- b) Follow the instructions specific to the make and model of your television or converter box to set the signal type to “ANTENNA’; “AIR’; or “BROADCAST’; not “Cable”.
- c) Go to the main menu of yourlV or converter box and complete a channel scan. This could be listed as “Auto Program’; “Auto Tuning’; or”Auto Channel Scan”. Consult the owner’s manual for your specific device and more precise guidelines. Be ready to experiment with various locations in your home. Remember to rescan for channels in every location.
- Make sure the antenna is facing the broadcast tower locations serving your area. Visit www.antennapointcom for more information on broadcasters and tower locations serving your area, or download the free Antenna Point app to your Android/iOS smartphone or tablet.
- You do not have a clear line of sight to your local broadcast towers. You might need to elevate and/or move your antenna. Remember to rescan for channels in every location.
- You are outside the range of your antenna’s capabilities. Depending upon the distance between your home and the local broadcast towers, you may need a long range outdoor/attic antenna. Antennas Direct offers many models for this purpose.
- You may have loose coaxial cable connections. Check ALL connections for a tight fit.
- Building materials such as brick, metal siding, radiant barrier, or stucco can greatly reduce the incoming signal. Do not place antennas on metallic surfaces, this interferes with 1V signal reception. Move your antenna to a window or wall facing the broadcast towers and rescan for available channels.
Problem: I’m receiving every channel except for one.
Possible cause:
- You may need to rescan the lVtuner or converter box. The channel you are not receiving may have its transmitter lower on the broadcast tower than the other transmitters and your line of sight is obstructed. Try elevating the antenna or moving it to another location. Repeat as needed.
Problem: I’m having signal breakups, but I’m only two miles from the
broadcast tower.
Possible causes:
- Your may be receiving interfering signals. A larger/stronger antenna will not necessarily solve this problem. Consider moving the antenna, making sure it is not placed near metal objects or other antennas. Call our helpline or chat with us online at antennasdirect.com for an analysis of your area and installation. We may be able to offer simple solutions.
- In some areas, broadcast signals are strong enough that an amplifier is not necessary. If you have completed the installation of the antenna with the In-Line Amplifier and reception is not as desired, remove the In-Line Amplifier and connect the antenna directly to the 1V using the coaxial cable. Remember to scan for channels every time you reposition or reconnect your antenna.
Warranty
Antennas Direct”‘ Inc. Antenna Lifetime Warranty
Antennas Direct™ Inc. warrants this product against any defects in
materials or workmanship for as long as you own the product. No warranty claim
will be honoured unless at the time the claim is made, you present proof of
purchase from an authorized Antennas Direct™ Inc. dealer. Antennas Direct™
Inc. will either repair or replace the defective product at no charge to you.
This warranty covers parts but does not cover any costs incurred in the
removal or reinstallation of the product. This limited warranty does not apply
if the product is damaged or fails due to: misuse, improper installation,
abuse, and modification of the product as originally manufactured by Antennas
Direct. Antennas Direct™ Inc. will not assume any liabilities for any other
warranties expressed or implied by any other person. The foregoing shall be
the sole and exclusive remedy of any person, whether in contract, tort, or
otherwise, and Antennas Direct™ Inc. shall not be liable for incidental or
consequential damage or commercial loss, or for any other loss or damage, as
set forth above.
16388 Westwoods Business Park, Ellisville, MO 63021, USA
Limited 90-Day Warranty JOLrM Switch In-Line Amplifier
Antennas Direct™ Inc. warrants this product against any defects in
materials or workmanship for ninety (90) days. No warranty claim will be
honoured unless at the time the claim is made, you present proof of purchase
from an authorized Antennas Direct™ Inc. dealer. Antennas Direct™ Inc. will
either repair or replace the defective product at no charge to you. This
warranty covers parts but does not cover any costs incurred in the removal or
reinstallation of the product. This limited warranty does not apply if the
product is damaged or fails due to: misuse, improper installation, abuse, and
modification of the product as originally manufactured by Antennas Direct.
Antennas Direct™ Inc. will not assume any liabilities for any other warranties
expressed or implied by any other person. The foregoing shall be the sole and
exclusive remedy of any person, whether in contract, tort, or otherwise, and
Antennas Direct™ Inc. shall not be liable for incidental or consequential
damage or commercial loss, or for any other loss or damage, as set forth
above.
16388 Westwoods Business Park, Ellisville, MO 63021, USA
FCC
AmpUfier Regulatory Notice: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause hannful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. This equipment has been tested and found to comply with the Um it’s for a Class B Digital Device, under Part 15 of the FCC Rules. These Um-its are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause hannful interference to radio communication. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the antenna.
- increase the separation between the equipment and the converter box.
- Connect the equipment to an outlet on a different circuit from which the converter box is connected.
- Consult the dealer or an experienced radio technician for help.
Call to Learn.
Toll-Free Helpline: 1-877-825-5572
Technical Assistance is available Monday – Friday, 9:00 am to 7:00 pm and
Saturday- Sunday, 10:00 am to 6:00 pm, Central Time.