NPF-40D-54 Single Output LED Driver Owner’s Manual

40W Single Output LED Driver
NPF-40 Dseries

NPF-40D-54 Single Output LED Driver

http://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf

Features

• Plastic housing with class II design
• Built-in active PFC function
• Class 2 power unit
• Standby power consumption <0.5W
• IP67 rating for indoor or outdoor installations
• Function: 3 in 1 dimming (dim-to-off)
• Typical lifetime >50000hours
• 5 years warranty

Applications

• LED panel lighting
• LED downlight
• LED decorative lighting
• LED tunnel lighting
• Moving sign
• Type “HL” for use in Class I, Division 2 hazardous (Classified) location

GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx

Description

NPF-40D series is a 40W AC/DC LED driver featuring the constant current mode output.
NPF-40D operates from 90~305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -40°°.~+85’C case temperature under free air convection.
The entire series is rated with IP67 ingress protection level and is suitable to work for a variety of applications at dry, damp or wet locations. NPF-40D is equipped with the 3 in 1 dimming function so as to provide the design flexibility for LED lighting system.

Model Encoding

SPECIFICATION

MODEL| NPF-40D-12| NPF-40D-15| NPF-40D-20| NPF- 40D-24| NPF-40D-30| NPF-40D-36| NPF-40D-42| NPF-40D-48| NPF-40D-54
---|---|---|---|---|---|---|---|---|---
OUTPUT| RATED CURRENT| 3.34A| 2.67A| 2A| 1.67A| 1.34A| 1.12A| 0.96A| 0.84A| 0.76A
RATED POWER| 40.08W| 40.08W| 40W| 40.08W| 40.2W| 40.32W| 40.32W| 40.32W| 41.04W
CONSTANT CURRENT REGION| 7.2 ~ 12V| 9 ~ 15V| 12 ~ 20V| 14.4 ~ 24V| 18 ~ 30V| 21.6 ~ 36V| 25.2 ~ 42V| 28.8 ~ 48V| 32.4 ~ 54V
CURRENT RIPPLE| 5.0% max. @rated current
CURRENT TOLERANCE| ±5.0%
SET UP TIME Note.3| 500ms/115VAC, 230VAC
INPUT| VOLTAGE RANGE Note.2| 90 ~ 305VAC         127 ~ 431VDC
(Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE| 47 ~ 63Hz
POWER FACTOR (Typ.)| PF≧0.97/115VAC, PF≧0.95/230VAC, PF≧0.92/277VAC@full load
(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
TOTAL HARMONIC DISTORTION| THD< 20%(@load≧60%/115VC, 230VAC; @load≧75%/277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY(Typ.)| 86%| 87%| 88%| 89%| 89%| 90%| 90%| 90%| 90%
AC CURRENT (Typ.)| 0.6A / 115VAC
0.3A / 230VAC
0.25A / 277VAC
INRUSH CURRENT(Typ.)| COLD START 50A(twidth=270μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER| 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| <0.25mA / 277VAC
STANDBY POWER CONSUMPTION| <0.5W
PROTECTION| OVER CURRENT| 95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT| Hiccup mode, recovers automatically after fault condition is removed
OVER VOLTAGE| 15 ~ 17V| 17.5 ~ 21V| 23 ~ 27V| 28 ~ 34V| 34 ~ 40V| 41 ~ 46V| 46 ~ 54V| 54 ~ 60V| 59 ~ 66V
Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE| Shut down o/p voltage, re-power on to recover
ENVIRONMENT| WORKING TEMP.| Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.| Tcase=+85℃
WORKING HUMIDITY| 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 50℃)
VIBRATION| 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC| SAFETY STANDARDS| UL8750(type”HL”), UL879(for 12V,24V only), CSA C22.2 No. 250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 independent, EAC TP TC 004, GB19510.1,GB19510.14,
IP67 approved ; Design refer to BS EN/EN60335-1
WITHSTAND VOLTAGE| I/P-O/P:3.75KVAC
ISOLATION RESISTANCE| I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@ load≧60%) ; BS EN/EN61000-3-3; GB/T 17743, GB17625.1,EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity Line-Line 2KV);EAC TP TC 020
OTHERS| MTBF| 3084.3K hrs min.      Telcordia SR-332 (Bellcore) ; 288.2K hrs min.      MIL-HDBK-217F (25℃)
DIMENSION| 1505335mm (LWH)
PACKING| 0.49Kg;30pcs/15.7Kg/1.0CUFT
NOTE| 1.  All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2.  De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
3.  Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
4.  The standby power consumption is specified for 230VAC.
5.  The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
6.  This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly  tc  point (or TMP, per DLC), is about 75℃ or less.
7.  Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com 
8.  The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
9.  For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

BLOCK DIAGRAM

DRIVING METHODS OF LED MODULE

※ This series works in constant current mode to directly drive the LEDs.

DIMMING OPERATION

※ 3 in 1 dimming function

• Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0~ 10VDC, or 10V PWM signal or resistance.
• Direct connecting to LEDs is suggested. Itis not suitable to be used with additional drivers.
• Dimming source current from power supply: 100pA (typ.}
  ◎ Applying additive 0 ~ 10VDC

Note :

1. Min. dimming level is about 6% and the output current is not defined when 0%< Iout<6%.
2. The output current could drop down to 0% when dimming input is about OkΩ or OVdc, or 10V PWM signal with 0% duty cycle.

INSTALLATION MANUAL
Please refer to: http://www.meanwell/.com/manual.html

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>