GIGABYTE Z690 AERO G Intel Motherboard User Manual

GIGABYTE Z690 AERO G Intel Motherboard

Specifications

• Model: Z690 AERO G DDR4
• Revision: 1101
• Socket: LGA1700
• Memory Type: DDR4
• PCIe Slots: PCIEX16
• SATA Ports: F_U32G, F_U32G2, F_U32G2_LAN
• USB Ports: USB 3.2 Gen 1 Hub, USB20
• Form Factor: ATX

Product Usage Instructions

Identifying Your Motherboard Revision

The revision number on your motherboard can be found under the label ‘REV: X.X’. Make sure to check this revision before updating the BIOS or drivers.

BIOS Setup

Access the BIOS setup by pressing the designated key during system boot. Configure settings as needed for optimal performance and functionality.

Installing the Operating System and Drivers

Follow the steps outlined in the Quick Installation Guide provided on the GIGABYTE website to set up your operating system and install the necessary drivers for proper functionality.

FAQs

• Q: Where can I find more product information?
  • A: For detailed product information, refer to the User’s Manual available on the GIGABYTE website or contact customer support.
• Q: How do I check my motherboard revision?
  • A: Look for the label ‘REV: X.X’ on your motherboard to identify the revision number before making any updates or changes.

“`

Z690 AERO G Z690 AERO G DDR4
User’s Manual
Rev. 1101 12ME-Z69AOG4-1101R
For more product details, please visit GIGABYTE’s website. https://www.gigabyte.com/Motherboard/Z690-AERO-G-rev-10?m=ma#kf https://www.gigabyte.com/Motherboard/Z690-AERO-G-DDR4-rev-10?m=ma#kf GIGABYTE will reduce paper use in order to fulfill the responsibilities of a global citizen. Also, to reduce the impacts on global warming, the packaging materials of this product are recyclable and reusable. GIGABYTE works with you to protect the environment.

Copyright © 2023 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE’s prior written permission.
For detailed product information, carefully read the User’s Manual. For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE’s
website.
https://download.gigabyte.com/FileList/Manual/mb_manual_quick- guide_am5.pdf?m=sw
For product-related information, check on our website at: https://www.gigabyte.com
Identifying Your Motherboard Revision The revision number on your motherboard looks like this: “REV: X.X.” For example, “REV: 1.0” means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.
Example:

Chapter 1

Product Introduction

1-1 Motherboard Layout

USB20

ATX_12V_2X2

ATX_12V_2X4_1

CPU_FAN

CPU_OPT

D_LED2

LED_C2

ATX

U32 DP_HDMI

USB 3.2 Gen 1 Hub

LGA1700

Z690 AERO G SYS_FAN6_PUMP EC_TEMP2

F_U320G F_U32

U32G2 U32C

U32G2_LAN U320G

AUDIO

110

80

60

Intel® 2.5GbE LAN

PCIEX16

M2A_CPU

DDR5_A1 DDR5_A2 DDR5_B1 DDR5_B2 THB_C1 THB_C2

M2_WIFI M2M_SB M2Q_SB M2P_SB

110

80

60

iTE®

110

Super I/O

80

60

CODEC

110

80

60

PCIEX4_1

PCIEX4_2

Intel® Z690

7 6

5 4

3 2

SATA3

USB 2.0 Hub

M_BIOS

EC_TEMP1 QFLED

BAT CLR_CMOS

F_AUDIO COM Temperature sensor

LED_C1

F_USB2

QFLASH_PLUS SYS_FAN2 SYS_FAN4

D_LED1

SPI_TPM

F_USB1

SYS_FAN1 SYS_FAN3

F_PANEL

CPU DRAM VGA BOOT

NOISE_SENSOR

RST RST_SW

– 4 –

SYS_FAN5_PUMP

USB20

ATX_12V_2X2

ATX_12V_2X4_1

U32 DP_HDMI

USB 3.2 Gen 1 Hub

LGA1700

CPU_FAN

CPU_OPT

D_LED2

LED_C2

ATX

Z690 AERO G DDR4 SYS_FAN6_PUMP EC_TEMP2

F_U32

U32G2 U32C

U32G2_LAN U320G

AUDIO

110

80

60

Intel® 2.5GbE LAN

PCIEX16

F_U320G

M2A_CPU

DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

THB_C1 THB_C2

M2_WIFI M2M_SB M2Q_SB M2P_SB

110

80

60

iTE®

110

Super I/O

80

60

CODEC

110

80

60

PCIEX4_1

PCIEX4_2

Intel® Z690

7 6

5 4

3 2

SATA3

USB 2.0 Hub

M_BIOS

EC_TEMP1 QFLED

BAT CLR_CMOS

F_AUDIO COM Temperature sensor

LED_C1

F_USB2

QFLASH_PLUS SYS_FAN2 SYS_FAN4

D_LED1

SPI_TPM

F_USB1

SYS_FAN1 SYS_FAN3

F_PANEL

CPU DRAM VGA BOOT

NOISE_SENSOR

RST RST_SW

– 5 –

1-2 Motherboard Block Diagram

PCI Express 5.0 Bus x16
PCI Express 4.0 Bus
1 M.2 Socket 3 (M2A_CPU)

CPU CLK+/- (80~800 MT/s)
DDR5 5600 (Note)/5200 (Note)/4800/4400 MT/sj DDR4 3200/3000/2933/2666/2400/2133 MT/sk
LGA1700 CPU

HDMI 1.4

DDI

Switch

DisplayPort In

1 PCI Express x16 DMI 4.0 DDI

BIOS

SPI

TPM

Bus

4 SATA 6Gb/s (SATA3 4~7)

PCI Express 4.0 Bus

Switch

2 M.2 Socket 3 (M2P_SB, M2Q_SB)

or

1 M.2 Socket 3 2 SATA 6Gb/s (M2M_SB) (SATA3 2, 3)

PCI Express 3.0 Bus

x4

x1

Intel® 2.5GbE LAN

RJ45 LAN

x1 M.2 WIFI

Intel® Z690 CODEC

1 USB Type-C®, with USB 3.2 Gen 1 support
2 USB Type-C®, with USB 3.2 Gen 2×2 support

2 USB 3.2 Gen 2 Type-A

USB 3.2 Gen 1 Hub

4 USB 3.2 Gen 1

2 USB 3.2 Gen 1

USB 2.0 Hub

4 USB 2.0/1.1

2 USB 2.0/1.1

eSPI iTE® Bus Super I/O

COM

2 PCI Express x4 Line Out
Mic S/PDIF Out

j Only for Z690 AERO G. k Only for Z690 AERO G DDR4. (Note) Actual support may vary by CPU.
– 6 –

Chapter 2

Hardware Installation

2-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user’s manual and follow these procedures:
· Prior to installation, make sure the chassis is suitable for the motherboard. · Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation. · Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components. · When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely. · When handling the motherboard, avoid touching any metal leads or connectors. · It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity. · Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container. · Before connecting or unplugging the power supply cable from the motherboard, make sure the power supply has been turned off. · Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard. · Before using the product, please verify that all cables and power connectors of your hardware components are connected. · To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components. · Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing. · Do not place the computer system on an uneven surface. · Do not place the computer system in a high-temperature or wet environment. · Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user. · If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. · If you use an adapter, extension power cable, or power strip, ensure to consult with its installation and/or grounding instructions.
– 7 –

2-2 Product Specifications

CPU Chipset Memory
Onboard Graphics Audio LAN

LGA1700 socket: Support for 13th Generation Intel® CoreTM Processors and 12th Generation Intel® CoreTM, Pentium® Gold and Celeron® Processors (Go to GIGABYTE’s website for the latest CPU support list.)
L3 cache varies with CPU
Intel® Z690 Express Chipset
13th Generation Intel® CoreTM i9/i7 Processors: – Support for DDR5 5600/5200/4800/4400 MT/s memory modules j
13th Generation Intel® CoreTM i5/i3 and 12th Generation Intel® CoreTM, Pentium® Gold and Celeron® Processors: – Support for DDR5 4800/4400 MT/s memory modules j
Support for DDR4 3200/3000/2933/2666/2400/2133 MT/s memory modules k 4 x DDR5 DIMM sockets supporting up to 192 GB (48 GB single DIMM capacity)
of system memory j 4 x DDR4 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity)
of system memory k Dual channel memory architecture Support for ECC Un- buffered DIMM 1Rx8/2Rx8 memory modules (operate in
non-ECC mode) Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules Support for Extreme Memory Profile (XMP) memory modules
(The CPU and memory configuration may affect the supported memory types, data rate (speed), and number of DRAM modules, please refer to “Memory Support List” on GIGABYTE’s website for more information.) Integrated Graphics Processor-Intel® HD Graphics support: – 1 x USB Type-C® port, supporting USB Type-C® and DisplayPort video
outputs and a maximum resolution of 4096×2304@60 Hz Support for drawing tablets and 20V@3A of power delivery. Support for DisplayPort 1.2 version and HDCP 2.3
– 1 x HDMI port, supporting a maximum resolution of 4096×2160@30 Hz Support for HDMI 1.4 version and HDCP 2.3.
(Graphics specifications may vary depending on CPU or graphics card support.) Realtek® ALC4080 CODEC High Definition Audio 2-channel analog output Support for S/PDIF Out
– 7.1-channel digital signals Actual output of digital signals may vary depending on the playback content and software used, and an external DAC is required.
Intel® 2.5GbE LAN chip (2.5 Gbps/1 Gbps/100 Mbps)

j Only for Z690 AERO G. k Only for Z690 AERO G DDR4.
– 8 –

Wireless

Communication

Module

Expansion Slots
Storage Interface

USB

Intel® Wi-Fi 6 AX201 (For PCB rev. 1.0) – WIFI a, b, g, n, ac, ax, supporting 2.4/5 GHz Dual-Band – BLUETOOTH 5.2 – Support for 11ax 160MHz wireless standard and up to 2.4 Gbps data rate Intel® Wi-Fi 6 AX200 (For PCB rev. 1.1) – WIFI a, b, g, n, ac, ax, supporting 2.4/5 GHz Dual-Band – BLUETOOTH 5.2 – Support for 11ax 160MHz wireless standard and up to 2.4 Gbps data rate Intel® Wi-Fi 6E AX210 (For PCB rev. 1.2) – WIFI a, b, g, n, ac, ax, supporting 2.4/5/6 GHz carrier frequency bands – BLUETOOTH 5.2 – Support for 11ax 160MHz wireless standard and up to 2.4 Gbps data rate (Actual data rate may vary depending on environment and equipment.)
1 x PCI Express x16 slot, running at x16 (PCIEX16) * For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot.
(The PCIEX16 slot conforms to PCI Express 5.0 standard.) 2 x PCI Express x16 slots, running at x4 (PCIEX4_1, PCIEX4_2) (The PCIEX4 slots conform to PCI Express 3.0 standard.)
CPU: – 1 x M.2 connector (Socket 3, M key, type 2260/2280/22110 PCIe 4.0 x4/x2
SSD support) (M2A_CPU) Chipset: – 2 x M.2 connectors (Socket 3, M key, type 2260/2280/22110 PCIe 4.0 x4/x2
SSD support) (M2P_SB, M2Q_SB) – 1 x M.2 connector (Socket 3, M key, type 2260/2280/22110 SATA and PCIe
4.0 x4/x2 SSD support) (M2M_SB) – 6 x SATA 6Gb/s connectors RAID 0, RAID 1, RAID 5, and RAID 10 support for NVMe SSD storage devices RAID 0, RAID 1, RAID 5, and RAID 10 support for SATA storage devices

• Refer to “2-7 Internal Connectors,” for the installation notices for the M.2 and SATA connectors.
  Chipset: – 2 x USB Type-C® ports, with USB 3.2 Gen 2×2 support (1 port on the back
  panel, 1 port available through the internal USB header) – 1 x USB Type-C® port on the back panel, with USB 3.2 Gen 1 support – 2 x USB 3.2 Gen 2 Type-A ports (red) on the back panel – 2 x USB 3.2 Gen 1 ports available through the internal USB header – 2 x USB 2.0/1.1 ports on the back panel Chipset+USB 3.2 Gen 1 Hub: – 4 x USB 3.2 Gen 1 ports on the back panel Chipset+USB 2.0 Hub: – 4 x USB 2.0/1.1 ports available through the internal USB headers

– 9 –

Internal Connectors
Back Panel Connectors I/O Controller

1 x 24-pin ATX main power connector 1 x 8-pin ATX 12V power connector 1 x 4-pin ATX 12V power connector 1 x CPU fan header 1 x CPU fan/water cooling pump header 4 x system fan headers 2 x system fan/water cooling pump headers 2 x addressable LED strip headers 2 x RGB LED strip headers 4 x M.2 Socket 3 connectors 6 x SATA 6Gb/s connectors 1 x front panel header 1 x front panel audio header 1 x USB Type-C® header, with USB 3.2 Gen 2×2 support 1 x USB 3.2 Gen 1 header 2 x USB 2.0/1.1 headers 1 x noise detection header 2 x ThunderboltTM add-in card connectors 1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI
2.0 module only) 1 x serial port header 1 x Q-Flash Plus button 1 x reset button 1 x reset jumper 2 x temperature sensor headers 1 x Clear CMOS jumper 2 x USB 2.0/1.1 ports 2 x SMA antenna connectors (2T2R) 4 x USB 3.2 Gen 1 ports 1 x DisplayPort In port 1 x HDMI port 2 x USB 3.2 Gen 2 Type-A ports (red) 1 x USB Type-C® port, with USB 3.2 Gen 2×2 support 1 x USB Type-C® port, with USB 3.2 Gen 1 support 1 x RJ-45 port 1 x optical S/PDIF Out connector 2 x audio jacks
iTE® I/O Controller Chip

– 10 –

Hardware

Monitor

BIOS

Unique Features

Bundled

Software

Operating

System

Form Factor

Voltage detection Temperature detection Fan speed detection Water cooling flow rate detection Fan fail warning Fan speed control

• Whether the fan (pump) speed control function is supported will depend on the fan (pump) you install.
  Noise detection
  1 x 256 Mbit flash Use of licensed AMI UEFI BIOS PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
  Support for APP Center * Available applications in APP Center may vary by motherboard model. Supported functions of each application may also vary depending on motherboard specifications.
  – @BIOS – EasyTune – RGB Fusion – Smart Backup – System Information Viewer Support for Q-Flash Plus Support for Q-Flash Support for Xpress Install
  Norton® Internet Security (OEM version) LAN bandwidth management software
  Support for Windows 11 64-bit Support for Windows 10 64-bit
  ATX Form Factor; 30.5cm x 24.4cm

• GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

& Please visit GIGABYTE’s website for support lists of CPU, memory modules, SSDs, and M.2 devices. https://www.gigabyte.com/Motherboard/Z690-AERO-G-rev-10?m=dl#support-dl https://www.gigabyte.com/Motherboard/Z690-AERO-G-DDR4-rev-10?m=dl#support-dl
& Please visit the SERVICE/SUPPORTUtility page on GIGABYTE’s website to download the latest version of apps. https://www.gigabyte.com/Support/Utility/Motherboard?m=ut
– 11 –

2-3 Installing the CPU and CPU Cooler
Read the following guidelines before you begin to install the CPU: · Make sure that the motherboard supports the CPU.
(Go to GIGABYTE’s website for the latest CPU support list.) · Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage. · Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.) · Apply an even and thin layer of thermal grease on the surface of the CPU. · Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur. · Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.
A. Note the CPU Orientation
Note the alignment keys on the motherboard CPU socket and the notches on the CPU.
Alignment Key

Triangle Pin One Marking of the CPU Socket

LGA1700 CPU Socket
Alignment Key Notch

Triangle Pin One Marking on the CPU

LGA1700 CPU

Notch
Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate automatically after you insert the CPU and close the load plate.

& Please visit GIGABYTE’s website for details on hardware installation. http://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw
– 12 –

B. Installing the CPU
Follow the steps below to correctly install the CPU into the motherboard CPU socket.

u

Finger Tab

jGently press the CPU socket lever handle down and away from the socket.
kCompletely lift up the CPU socket locking lever.
lUse the finger tab on the side of the metal load plate to lift open the metal load plate with the plastic protective cover attached to it.

l k

j

v
Hold the CPU with your fingers by the edges. Align the CPU pin one marking (triangle) with the pin one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently insert the CPU into position.

Pin One

w
j
Make sure the CPU is properly installed and

then close the load plate. The plastic protec-

tive cover will pop off, just remove it. Secure

the lever under its retention tab to complete

the installation of the CPU. * Always replace the plastic protective cover

k

when the CPU is not installed to protect the CPU socket.

l

Do not force to engage the CPU socket locking lever when the CPU is not installed correctly as this would damage the CPU and CPU socket.
– 13 –

C. Installing the CPU Cooler
Be sure to install the CPU cooler after installing the CPU. (Actual installation process may differ depending the CPU cooler to be used. Refer to the user’s manual for your CPU cooler.)
u
Apply an even and thin layer of thermal grease on the surface of the installed CPU.

v
Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Push down on the push pins diagonally.

j k
k
j

w
Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard.

– 14 –

CPU_FAN

2-4 Installing the Memory

Read the following guidelines before you begin to install the memory: · Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used. (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.) · Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. · Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The four memory sockets are divided into two channels and each channel has two memory sockets as following: Channel A: DDR5_A1j/DDR4_A1k, DDR5_A2j/DDR4_A2k Channel B: DDR5_B1j/DDR4_B1k, DDR5_B2j/DDR4_B2k

• Recommended Dual Channel Memory Configuration:
  DDR5_A1j DDR5_A2j DDR5_B1j DDR4_A1k DDR4_A2k DDR4_B1k

2 Modules

– –

DS/SS

– –

4 Modules

DS/SS

DS/SS

DS/SS

(SS=Single-Sided, DS=Double-Sided, “- -“=No Memory)

DDR5_B2j DDR4_B2k
DS/SS
DS/SS

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled if only one memory module is installed. 2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of
the same capacity, brand, speed, and chips be used.

DDR5_A1j/DDR4_A1k DDR5_A2j/DDR4_A2k DDR5_B1j/DDR4_B1k
DDR5_B2j/DDR4_B2k
When installing a single memory module, we recommend that you install it in the DDR5_A2j/ DDR4_A2k or DDR5_B2j/DDR4_B2ksocket.
j Only for Z690 AERO G. k Only for Z690 AERO G DDR4.
– 15 –

2-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card: · Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card. · Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage. Follow the steps below to correctly install your expansion card in the expansion slot. 1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel. 2. Align the card with the slot, and press down on the card until it is fully seated in the slot. 3. Make sure the metal contacts on the card are completely inserted into the slot. 4. Secure the card’s metal bracket to the chassis back panel with a screw. 5. After installing all expansion cards, replace the chassis cover(s). 6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your
expansion card(s). 7. Install the driver provided with the expansion card in your operating system.
PCIEX16 Slot
– 16 –

2-6 Back Panel Connectors
USB 2.0/1.1 Port The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices. SMA Antenna Connectors (2T2R) Use this connector to connect an antenna.
Tighten the antennas to the antenna connectors and then aim the antennas correctly for better signal reception. USB 3.2 Gen 1 Port The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0 specification. Use this port for USB devices. DisplayPort In port The DisplayPort In port offers video outputs to the motherboard. Refer to the pictures below and the USB Type-C® (USB 3.2 Gen 1) port for more information.

Step 1: Connect your DisplayPort cable or MiniDisplayPort cable (purchased separately) from the graphics card to the DisplayPort In port on the back panel.

Step 2: Then connect the USB Type-C® or DisplayPort devices to USB Type-C® port to complete.

After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The item name may differ depending on your operating system.)
· When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
· When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
– 17 –

USB 3.2 Gen 2 Type-A Port (Red)

The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1 and USB 2.0 specification. Use this port for USB devices.

USB Type-C® Port (with USB 3.2 Gen 1 Support)

This port supports GIGABYTE VisionLINK technology and has display and data transmission capabilities

with 20V@3A(60W) of power delivery. You can connect a drawing tablet to this port. This port also supports standard USB Type-C® and DisplayPort display output. You can connect a USB Type-C® monitor to this port or use an adapter cable to connect a standard DisplayPort monitor. The maximum

supported resolution is 4096×2304@60 Hz when using a DisplayPort monitor, but the actual resolutions supported are dependent on the monitor being used. The reversible USB port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0 specification. You can use this port for USB devices, too.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 2.5 Gbps data rate. The following

describes the states of the LAN port LEDs.

Speed LED

Activity LED

Speed LED:

State

Description

Activity LED: State Description

Green

2.5 Gbps data rate

Blinking Data transmission or receiving is occurring

Orange 1 Gbps data rate

On

No data transmission or receiving is occurring

LAN Port

Off

100 Mbps data rate

USB 3.2 Gen 2 Type-A Port (Q-Flash Plus Port)
The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1 and USB 2.0 specification. Use this port for USB devices. Before using Q-Flash Plus , (Note) make sure to insert the USB flash drive into this port first. USB Type-C® Port (with USB 3.2 Gen 2×2 Support) The reversible USB port supports the USB 3.2 Gen 2×2 specification and is compatible to the USB 3.2 Gen 2, USB 3.2 Gen 1, and USB 2.0 specifications. Use this port for USB devices. Line Out
The line out jack. Mic In
The Mic in jack. Optical S/PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector.

(Note) To enable the Q-Flash Plus function, please navigate to the “Unique Features” page of GIGABYTE’s website for more information.
& Please visit GIGABYTE’s website for details on configuring the audio software. https://www.gigabyte.com/WebPage/699/realtek4080-audio.html
– 18 –

2-7 Internal Connectors
1

6 38 9

2

7 5

16

12

15

25

12

20

12

10

12

11

22 23

14 18 8 9 19 17 7 24 4 21 13

1. ATX_12V_2X2/ATX_12V_2X4_1 2) ATX 3) CPU_FAN 4) SYS_FAN1/2/3/4 5) SYS_FAN5/6_PUMP 6) CPU_OPT 7) EC_TEMP1/EC_TEMP2 8) D_LED1/D_LED2 9) LED_C1/LED_C2 10) NOISE_SENSOR 11) SATA3 2/3/4/5/6/7 12) M2A_CPU/M2P_SB/M2Q_SB/M2M_SB 13) F_PANEL

2. F_AUDIO 15) F_U320G 16) F_U32 17) F_USB1/F_USB2 18) COM 19) SPI_TPM 20) THB_C1/THB_C2 21) CLR_CMOS 22) RST_SW/RST 23) BAT 24) QFLASH_PLUS 25) CPU/DRAM/VGA/BOOT

Read the following guidelines before connecting external devices: · First make sure your devices are compliant with the connectors you wish to connect. · Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices. · After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
– 19 –

1/2) ATX_12V_2X2/ATX_12V_2X4_1/ATX (2×2, 2×4 12V Power Connectors and 2×12 Main
Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

3

4

1

2

ATX_12V_2X2

ATX_12V_2X2:
Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V

5

8

1

4

ATX_12V_2X4_1

ATX_12V_2X4_1:
Pin No. Definition 1 GND (Only for 2×4-pin 12V) 2 GND (Only for 2×4-pin 12V) 3 GND 4 GND 5 +12V (Only for 2×4-pin 12V) 6 +12V (Only for 2×4-pin 12V) 7 +12V 8 +12V

12

24

1

13

ATX

ATX:
Pin No. 1 2 3 4 5 6 7 8 9 10 11
12

Definition

Pin No.

3.3V

13

3.3V

14

GND

15

+5V

16

GND

17

+5V

18

GND

19

Power Good

20

5VSB (stand by +5V)

21

+12V

22

+12V (Only for 2×12-pin 23

ATX) 3.3V (Only for 2×12-pin 24

ATX)

Definition 3.3V -12V GND PS_ON (soft On/Off) GND GND GND NC +5V +5V +5V (Only for 2×12-pin ATX)
GND (Only for 2×12-pin ATX)

– 20 –

3/4) CPU_FAN/SYS_FAN1/2/3/4 (Fan Headers) All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

1 CPU_FAN
1 SYS_FAN1/SYS_FAN2/ SYS_FAN3/SYS_FAN4

Pin No. 1 2 3 4

Definition GND Voltage Speed Control Sense PWM Speed Control

5. SYS_FAN5/6_PUMP (System Fan/Water Cooling Pump Headers) The fan/pump headers are 4-pin. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. The header also provides speed control for a water cooling pump. Please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “Smart Fan 6” for more information.

Pin No. Definition

1 GND

2 Voltage Speed Control

1

3 Sense

4 PWM Speed Control

· Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
· These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
– 21 –

6. CPU_OPT (CPU Fan/Water Cooling Pump Header) The fan/pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design.

Pin No. Definition

1

1 GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

Connector Maximum Current Maximum Power

CPU_FAN 2A 24W

SYS_FAN1~4 2A 24W

SYS_FAN5~6_PUMP 2A 24W

CPU_OPT 2A 24W

7. EC_TEMP1/EC_TEMP2 (Temperature Sensor Headers) Connect the thermistor cables to the headers for temperature detection.

1 EC_TEMP2

Pin No. Definition 1 SENSOR IN 2 GND

1 EC_TEMP1

– 22 –

8. D_LED1/D_LED2 (Addressable LED Strip Headers) The headers can be used to connect a standard 5050 addressable LED strip, with maximum power rating of 5A (5V) and maximum number of 1000 LEDs.

1 D_LED2
1 D_LED1

Pin No. 1 2 3 4

Definition V (5V) Data No Pin GND

Connect your addressable LED strip to the header. The power pin (marked with a triangle on the plug) of the LED strip must be connected to Pin 1 of the addressable LED strip header. Incorrect connection may lead to the damage of the LED strip.

Addressable LED Strip
1

9. LED_C1/LED_C2 (RGB LED Strip Headers) The headers can be used to connect a standard 5050 RGB LED strip (12V/G/R/B), with maximum power rating of 2A (12V) and maximum length of 2m.

1 LED_C2
1 LED_C1

Pin No. 1 2 3 4

Definition 12V G R B

Connect your RGB LED strip to the header. The power pin (marked with a triangle on the plug) of the LED strip must be connected to Pin 1 (12V) of this header. Incorrect connection may lead to the damage of the LED strip.
1 12V

RGB LED Strip

For how to turn on/off the lights of the LED strip, please navigate to the “Unique Features” page of GIGABYTE’s website.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.
– 23 –

10. NOISE_SENSOR (Noise Detection Header) This header can be used to connect a noise detection cable to detect the noise inside the case.
    Pin No. Definition 1 Noise Detection 2 GND
    1
    Noise Detection Cable
    1

For more information on the noise detection function, please navigate to the “Unique Features” page of GIGABYTE’s website and search for “System Information Viewer.”
Before connecting the cable to the header, make sure to remove the jumper cap; re-place the jumper cap if the header is not in use.

11. SATA3 2/3/4/5/6/7 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel® Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Please navigate to the “Configuring a RAID Set” page of GIGABYTE’s website for instructions on configuring a RAID array.

G.QBOFM G.QBOFM G.QBOFM

7 7
SATA3 3 5 7 246

Pin No. Definition

1 GND

1

2 TXP

1

3 TXN

4 GND

5 RXN

6 RXP

7 GND

To enable hot-plugging for the SATA ports, please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “SATA Configuration” for more information.
– 24 –

12. M2A_CPU/M2P_SB/M2Q_SB/M2M_SB (M.2 Socket 3 Connectors) There are two types of M.2 SSDs: M.2 SATA SSDs and M.2 PCIe SSDs. Be sure to verify which type of M.2 SSDs is supported by the M.2 socket you want to use. Please note that an M.2 PCIe SSD cannot be used to create a RAID set either with an M.2 SATA SSD or a SATA hard drive. Please navigate to the “Configuring a RAID Set” page of GIGABYTE’s website for instructions on configuring a RAID array.

110

80

60

M2A_CPU

110

80

60

110

80

60

110

80

60

M2P_SB M2Q_SB M2M_SB

Follow the steps below to correctly install an M.2 SSD in the M.2 connector. Step 1: Locate the M.2 connector where you will install the M.2 SSD, use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink. Step 2: Locate the proper mounting hole based on the length of your M.2 SSD drive. If needed, move the standoff to the desired mounting hole. Insert the M.2 SSD into the M.2 connector at an angle. Step 3: Press the M.2 SSD down and then use the included screw to secure it in the connector. Remove the protective film from the bottom of the heatsink. Then replace the heatsink and secure it to the original hole.

• Types of M.2 SSDs supported by each M.2 connector:

M.2 PCIe x4 SSD M.2 PCIe x2 SSD

M2A_CPU

a

a

M2P_SB

a

a

M2Q_SB

a

a

M2M_SB

a

a

M.2 SATA SSD r r r a

– 25 –

Installation Notices for the M.2 and SATA Connectors: The availability of the SATA connectors may be affected by the type of device installed in the M.2 sockets. The M2M_SB connector shares bandwidth with the SATA3 2, 3 connector. Refer to the following tables for details.

· M2A_CPU:

Type of M.2 SSD

Connector

M.2 PCIe SSD

SATA3 2 a

No M.2 SSD Installed

a

a: Available, r: Not available

· M2P_SB:

Type of M.2 SSD

Connector

M.2 PCIe SSD

SATA3 2 a

No M.2 SSD Installed

a

a: Available, r: Not available

SATA3 3 a a
SATA3 3 a a

SATA3 4 a a
SATA3 4 a a

SATA3 5 a a
SATA3 5 a a

SATA3 6 a a
SATA3 6 a a

SATA3 7 a a
SATA3 7 a a

· M2Q_SB:

Type of M.2 SSD

Connector

M.2 PCIe SSD

SATA3 2 a

No M.2 SSD Installed

a

a: Available, r: Not available

· M2M_SB:

Type of M.2 SSD

Connector

M.2 SATA SSD

SATA3 2 a

M.2 PCIe SSD

r

No M.2 SSD Installed

a

a: Available, r: Not available

SATA3 3 a a
SATA3 3 a r a

SATA3 4 a a
SATA3 4 a a a

SATA3 5 a a
SATA3 5 a a a

SATA3 6 a a
SATA3 6 a a a

SATA3 7 a a
SATA3 7 a a a

– 26 –

13. F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
    Power LED Power Switch Speaker

PLED+ PLED-
PW+ PWSPEAK+ NC NC SPEAK-

2

20

1

19

HD+ HD-
RESRES+
CICI+
PWR_LED+ PWR_LEDPWR_LED-

Hard Drive Activity LED

Reset Switch

Power LED
Chassis Intrusion Header

· PLED/PWR_LED (Power LED):

System Status LED Connects to the power status indicator on the chassis front panel. The LED

S0

On

S3/S4/S5

Off

is on when the system is operating. The LED is off when the system is in S3/ S4 sleep state or powered off (S5).

· PW (Power Switch): Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “Soft-Off by PWR-BTTN” for more information).
· SPEAK (Speaker): Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.
· HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
· RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
· CI (Chassis Intrusion Header): Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.
· NC: No connection.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
– 27 –

14. F_AUDIO (Front Panel Audio Header) The front panel audio header supports High Definition audio (HD). You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

9

1

10

2

Pin No. 1 2 3 4 5 6 7 8 9
10

Definition MIC L GND MIC R NC Head Phone R MIC Detection SENSE_SEND No Pin Head Phone L Head Phone Detection

Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

15. F_U320G (USB Type-C® Header with USB 3.2 Gen 2×2 Support) The header conforms to USB 3.2 Gen 2×2 specification and can provide one USB port.

Pin No. Definition

Pin No. Definition

10

11

1 VBUS

11 VBUS

2 TX1+

12 TX2+

1

20

3 TX14 GND

13 TX214 GND

5 RX1+

15 RX2+

6 RX1-

16 RX2-

7 VBUS

17 GND

8 CC1

18 D-

9 SBU1

19 D+

10 SBU2

20 CC2

– 28 –

16. F_U32 (USB 3.2 Gen 1 Header) The header conforms to USB 3.2 Gen 1 and USB 2.0 specification and can provide two USB ports. For purchasing the optional 3.5″ front panel that provides two USB 3.2 Gen 1 ports, please contact the local dealer.

Pin No. Definition

Pin No. Definition

20

1

1 VBUS

11 D2+

2 SSRX1-

12 D2-

3 SSRXG1.+QBOFM 13 GND

4 GND

14 SSTX2+

5 SSTX1-

15 SSTX2-

6 SSTX1+

11

10

7 GND

16 GND 17 SSRX2+

8 D1-

18 SSRX2-

9 D1+

19 VBUS

10 NC

20 No Pin

17. F_USB1/F_USB2 (USB 2.0/1.1 Headers) The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

9

1

10

2

Pin No. 1 2 3 4 5 6 7 8 9 10

Definition Power (5V) Power (5V) USB DXUSB DYUSB DX+ USB DY+ GND GND No Pin NC

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.

– 29 –

18. COM (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer.

9

1

10

2

Pin No. 1 2 3 4 5 6 7 8 9 10

Definition NDCDNSIN NSOUT NDTRGND NDSRNRTSNCTSNRINo Pin

19. SPI_TPM (Trusted Platform Module Header) You may connect an SPI TPM (Trusted Platform Module) to this header.

Pin No. Definition

1 Data Output

11

1

2 Power (3.3V)

12

2

3 No Pin

4 NC

5 Data Input

6 CLK

7 Chip Select

8 GND

9 IRQ

10 NC

11 NC

12 RST

– 30 –

20. THB_C1/THB_C2 (ThunderboltTM Add-in Card Connectors) The connectors are used to connect to a GIGABYTE ThunderboltTM add-in card.
    1 THB_C2
    1 THB_C1
    Supports a ThunderboltTM add-in card.

21. CLR_CMOS (Clear CMOS Jumper) Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
    Open: Normal Short: Clear CMOS Values
    · Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.
    · After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (please navigate to the “BIOS Setup” page of GIGABYTE’s website for more information). – 31 –

22. RST_SW/RST (Reset Button/Reset Jumper) The reset button (RST_SW) allows users to quickly turn on/off the computer in an open-case environment when they want to change hardware components or conduct hardware testing. The reset jumper (RST) can connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

Pin No. Definition

1 Reset

1

2 GND

RST_SW
RST_SW RST
The reset button (RST_SW)/rest jumper (RST) provides you with several functions to use. To remap the button to perform different tasks, please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “RST_SW (MULTIKEY)” for more information.
23) BAT (Battery) The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery: 1. Turn off your computer and unplug the power cord. 2. Gently remove the battery from the battery holder and wait for one
minute. (Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.) 3. Replace the battery. 4. Plug in the power cord and restart your computer.
· Always turn off your computer and unplug the power cord before replacing the battery. · Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model. · Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model. · When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up). · Used batteries must be handled in accordance with local environmental regulations.
– 32 –

24. QFLASH_PLUS (Q-Flash Plus Button) Q-Flash Plus allows you to update the BIOS when your system is off (S5 shutdown state). Save the latest BIOS on a USB thumb drive and plug it into the dedicated port, and then you can now flash the BIOS automatically by simply pressing the Q-Flash Plus button. The QFLED will flash when the BIOS matching and flashing activities start and will stop flashing when the main BIOS flashing is complete.
    QFLED
    QFLASH_PLUS
    To enable the Q-Flash Plus function, please navigate to the “Unique Features” page of GIGABYTE’s website for more information.
25. CPU/DRAM/VGA/BOOT (Status LEDs) The status LEDs show whether the CPU, memory, graphics card, and operating system are working properly after system power-on. If the CPU/DRAM/VGA LED is on, that means the corresponding device is not working normally; if the BOOT LED is on, that means you haven’t entered the operating system yet.
    DRAM BOOT CPU VGA
    CPU: CPU status LED DRAM: Memory status LED VGA: Graphics card status LED BOOT: Operating system status LED
    – 33 –

Chapter 3

BIOS Setup

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS. To access the BIOS Setup program, press the key during the POST when the power is turned on. To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
· Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system. · @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS. For instructions on using the Q-Flash and @BIOS utilities, please navigate to the “Unique Features” page of GIGABYTE’s website and search for “BIOS Update Utilities.”
· Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.
· It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system’s failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
· Refer to the introductions of the battery/clear CMOS jumper in Chapter 2 or navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “Load Optimized Defaults” for how to clear the CMOS values.
& Please visit GIGABYTE’s website for details on configuring BIOS Setup. https://www.gigabyte.com/WebPage/819/z690-bios.html – 34 –

Startup Screen: The following startup Logo screen will appear when the computer boots.
Function Keys
Function Keys: : BIOS SETUPQ-FLASH
Press the key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup. : BOOT MENU
Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up arrow key or the down arrow key to select the first boot device, then press to accept. The system will boot from the device immediately. Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order will still be based on BIOS Setup settings. : Q-FLASH Press the key to access the Q-Flash utility directly without having to enter BIOS Setup first.
– 35 –