GIGABYTE Z790 D AX Motherboard User Manual

Z790 D AX Motherboard

“`html

Specifications:

• Model: Z790 D
• Form Factor: ATX
• Socket: LGA1700
• Memory Type: DDR5
• Expansion Slots: PCIEX16, PCIEX4, 3x PCIEX1
• Storage: SATA3, M.2

Product Usage Instructions:

Identifying Your Motherboard Revision:

The revision number on your motherboard can be found near the
model name. Check the revision before updating BIOS or drivers.

BIOS Setup:

Access the BIOS setup by pressing the specified key during
system boot. Configure settings according to your preferences or
system requirements.

Operating System and Drivers Installation:

1. Install the operating system by booting from the installation
   media and following on-screen instructions.

2. Install drivers by using the provided driver discs or
   downloading them from the manufacturer’s website.

Motherboard Layout:

Refer to the motherboard layout diagram to identify different
components and connectors on the motherboard for installation or
troubleshooting purposes.

FAQ:

How can I check the motherboard revision?

The motherboard revision is typically located near the model
name on the board itself. It is represented as “REV: X.X”.

Where can I find more detailed product information?

For detailed product information, refer to the User’s Manual
available on the manufacturer’s website. You can also visit the
support section of the Gigabyte website for additional
resources.

“`

Z790 D AX Z790 D AC Z790 D
User’s Manual
Rev. 1002
GIGABYTE will reduce paper use in order to fulfill the responsibilities of a global citizen. Also, to reduce the impacts on global warming, the packaging materials of this product are recyclable and reusable. GIGABYTE works with you to protect the environment. For more product details, please visit GIGABYTE’s website.

Copyright © 2024 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE’s prior written permission.
For detailed product information, carefully read the User’s Manual. For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE’s
website.
https://download.gigabyte.com/FileList/Manual/mb_manual_installation- guide_12QM-100xR.pdf
For product-related information, check on our website at: https://www.gigabyte.com
Identifying Your Motherboard Revision The revision number on your motherboard looks like this: “REV: X.X.” For example, “REV: 1.0” means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.
Example:

Table of Contents
Chapter 1 Product Introduction……………………………………………………………………………4 1-1 Motherboard Layout…………………………………………………………………………….. 4 1-2 Box Contents………………………………………………………………………………………. 5
Chapter 2 Hardware Installation ………………………………………………………………………….6 2-1 Installation Precautions………………………………………………………………………… 6 2-2 Product Specifications………………………………………………………………………….. 7 2-3 Installing the CPU and CPU Cooler ……………………………………………………… 11 2-4 Installing the Memory …………………………………………………………………………. 14 2-5 Installing an Expansion Card ………………………………………………………………. 15 2-6 Back Panel Connectors………………………………………………………………………. 16 2-7 Onboard Buttons and LEDs ………………………………………………………………… 18 2-8 Internal Connectors……………………………………………………………………………. 20
Chapter 3 BIOS Setup ……………………………………………………………………………………..32
Chapter 4 Installing the Operating System and Drivers…………………………………………34 4-1 Operating System Installation ……………………………………………………………… 34 4-2 Drivers Installation……………………………………………………………………………… 35
Chapter 5 Appendix …………………………………………………………………………………………36 5-1 Configuring a RAID Set………………………………………………………………………. 36 Regulatory Notices………………………………………………………………………………………. 37 Contact Us …………………………………………………………………………………………………. 41
– 3 –

Chapter 1 Product Introduction

1-1 Motherboard Layout

ATX_12V_2X4_1 KB_MS_USB20 SYS_FAN1
M2_WIFIjk

ATX_12V_2X4_2

CPU_OPT

CPU_FAN

D_LED2

ATX

LGA1700 U32

DP_HDMI

U32G2C U32G2

U32_LAN
AUDIO 110

Z790 D AX/ Z790 D AC/Z790 D
80

M2A_CPU

Realtek® 2.5GbE LAN

PCIEX16 PCIEX1_1k

iTE® Super I/O

PCIEX1_2jl 80

DDR5_A1 DDR5_A2 DDR5_B1 DDR5_B2

SYS_FAN2B SYS_FAN2A

F_U32

F_U32C

Intel® Z790

THB_C2 THB_C1

M2M_SB M2P_SB

CODEC

PCIEX1_3 80 PCIEX1_4 PCIEX4

USB 2.0 Hub

M_BIOS QFLED RST

BAT CLR_CMOS

SATA3

5 4

7 6

VGA CPU BOOT DRAM

F_AUDIO SPDIF_O
j Only for Z790 D AX. k Only for Z790 D AC. l Only for Z790 D.

D_LED1

F_USB2

QFLASH_PLUS RST_SW

SPI_TPM

F_USB1

SYS_FAN3_PUMP

F_PANEL Temperature sensor

– 4 –

1-2 Box Contents
5 Z790 D AX, Z790 D AC, or Z790 D motherboard 5 User’s Manual 5 Two antennasjk 5 Two SATA cables 5 I/O Shield 5 M.2 screw(s)
j Only for Z790 D AX. k Only for Z790 D AC. * The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
– 5 –

Chapter 2 Hardware Installation
2-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user’s manual and follow these procedures:
· Prior to installation, make sure the chassis is suitable for the motherboard. · Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation. · Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components. · When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely. · When handling the motherboard, avoid touching any metal leads or connectors. · It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity. · Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container. · Before connecting or unplugging the power supply cable from the motherboard, make sure the power supply has been turned off. · Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard. · Before using the product, please verify that all cables and power connectors of your hardware components are connected. · To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components. · Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing. · Do not place the computer system on an uneven surface. · Do not place the computer system in a high-temperature or wet environment. · Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user. · If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. · If you use an adapter, extension power cable, or power strip, ensure to consult with its installation and/or grounding instructions.
– 6 –

2-2 Product Specifications

CPU

LGA1700 socket: Support for the 14th, 13th, and 12th Generation Intel® CoreTM,

Pentium® Gold and Celeron® Processors

(Go to GIGABYTE’s website for the latest CPU support list.)

L3 cache varies with CPU

Chipset

Intel® Z790 Express Chipset

Memory
Onboard Graphics Audio

14th and 13th Generation Intel® CoreTM i9/i7 Pocessors:
– Support for DDR5 5600/5200/4800/4400 MT/s memory modules 13th Generation Intel® CoreTM i5/i3 and 12th Generation Intel® CoreTM, Pentium®
Gold and Celeron® Processors:
– Support for DDR5 4800/4400 MT/s memory modules 4 x DDR5 DIMM sockets supporting up to 192 GB (48 GB single DIMM capacity)
of system memory Dual channel memory architecture Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in
non-ECC mode) Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules Support for Extreme Memory Profile (XMP) memory modules
(The CPU and memory configuration may affect the supported memory types, data
rate (speed), and number of DRAM modules, please refer to “Memory Support
List” on GIGABYTE’s website for more information.)
Integrated Graphics Processor-Intel® HD Graphics support:
– 1 x HDMI port, supporting a maximum resolution of 4096×2160@60 Hz * Support for HDMI 2.1 version and HDCP 2.3.
* Support for native HDMI 2.1 TMDS compatible ports.
– 1 x DisplayPort, supporting a maximum resolution of 4096×2304@60 Hz Support for DisplayPort 1.2 version and HDCP 2.3
(Graphics specifications may vary depending on CPU support.)
Realtek® Audio CODEC High Definition Audio 2/4/5.1/7.1-channel

• You can change the functionality of an audio jack using the audio software. To configure
  7.1-channel audio, access the audio software for audio settings. Support for S/PDIF Out

LAN

Realtek® 2.5GbE LAN chip (2.5 Gbps/1 Gbps/100 Mbps)

Wireless

Intel® Wi-Fi 6E AX211 (PCB rev. 1.0)

Communication

– WIFI a, b, g, n, ac, ax, supporting 2.4/5/6 GHz carrier frequency bands

Modulej

– BLUETOOTH 5.3

– Support for 11ax 160MHz wireless standard

Realtek® Wi-Fi 6E RTL8852CE(PCB rev. 1.1)

– WIFI a, b, g, n, ac, ax, supporting 2.4/5/6 GHz carrier frequency bands

– BLUETOOTH 5.3

– Support for 11ax 160MHz wireless standard

(Actual data rate may vary depending on environment and equipment.)

j Only for Z790 D AX. k Only for Z790 D AC.
– 7 –

Wireless

Communication

Modulek

Expansion

Slotsjl

Expansion

Slotsk

Storage Interface

USB

Intel® Wireless- AC 9560 (PCB rev. 1.0) – WIFI 802.11 a, b, g, n, ac, supporting 2.4/5 GHz Dual-Band – BLUETOOTH 5.1
– Support 11ac 160MHz wireless standard (Actual data rate may vary depending on environment and equipment.)
CPU: – 1 x PCI Express x16 slot, supporting PCIe 5.0 and running at x16 (PCIEX16)

• The PCIEX16 slot can only support a graphics card or an NVMe SSD. If only one graphics card is to be installed, be sure to install it in the PCIEX16 slot.
  Chipset: – 1 x PCI Express x16 slot, supporting PCIe 4.0 and running at x4 (PCIEX4) – 1 x PCI Express x16 slot, supporting PCIe 3.0 and running at x1 (PCIEX1_4) – 2 x PCI Express x1 slots, supporting PCIe 3.0 and running at x1 (PCIEX1_2,
  PCIEX1_3)
  CPU: – 1 x PCI Express x16 slot, supporting PCIe 5.0 and running at x16 (PCIEX16)
• The PCIEX16 slot can only support a graphics card or an NVMe SSD. If only one graphics card is to be installed, be sure to install it in the PCIEX16 slot.
  Chipset: – 1 x PCI Express x16 slot, supporting PCIe 4.0 and running at x4 (PCIEX4) – 2 x PCI Express x16 slots, supporting PCIe 3.0 and running at x1 (PCIEX1_1,
  PCIEX1_4) – 1 x PCI Express x1 slot, supporting PCIe 3.0 and running at x1 (PCIEX1_3)
  CPU: – 1 x M.2 connector (Socket 3, M key, type 22110/2280 PCIe 4.0 x4/x2 SSD
  support) (M2A_CPU) Chipset: – 1 x M.2 connectors (Socket 3, M key, type 2280 PCIe 4.0 x4/x2 SSD support)
  (M2P_SB) – 1 x M.2 connectors (Socket 3, M key, type 2280 SATA and PCIe 4.0 x4/x2
  SSD support) (M2M_SB) – 4 x SATA 6Gb/s connectors RAID 0, RAID 1, RAID 5, and RAID 10 support for NVMe SSD storage devices RAID 0, RAID 1, RAID 5, and RAID 10 support for SATA storage devices
  Chipset: – 1 x USB Type-C® port on the back panel, with USB 3.2 Gen 2 support – 1 x USB Type-C® port with USB 3.2 Gen 1 support, available through the
  internal USB header – 1 x USB 3.2 Gen 2 Type-A port (red) on the back panel – 6 x USB 3.2 Gen 1 ports (4 ports on the back panel, 2 ports available
  through the internal USB header) – 2 x USB 2.0/1.1 ports on the back panel Chipset+USB 2.0 Hub: – 4 x USB 2.0/1.1 ports, available through the internal USB headers

j Only for Z790 D AX. k Only for Z790 D AC.
l Only for Z790 D.

– 8 –

Internal Connectors
Back Panel Connectors
I/O Controller Hardware Monitor

1 x 24-pin ATX main power connector 2 x 8-pin ATX 12V power connectors 1 x CPU fan header 1 x CPU fan/water cooling pump header 3 x system fan headers 1 x system fan/water cooling pump header 2 x addressable LED strip headers 3 x M.2 Socket 3 connectors 4 x SATA 6Gb/s connectors 1 x front panel header 1 x front panel audio header 1 x S/PDIF Out header 1 x USB Type-C® header, with USB 3.2 Gen 1 support 1 x USB 3.2 Gen 1 header 2 x USB 2.0/1.1 headers 2 x ThunderboltTM add-in card connectors 1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI 2.0/
GC-TPM2.0 SPI V2 module only) 1 x reset button 1 x Q-Flash Plus button 1 x reset jumper 1 x Clear CMOS jumper
1 x PS/2 keyboard/mouse port 1 x USB Type-C® port, with USB 3.2 Gen 2 support 1 x USB 3.2 Gen 2 Type-A port (red) 4 x USB 3.2 Gen 1 ports 2 x USB 2.0/1.1 ports 2 x SMA antenna connectors (2T2R)jk 1 x HDMI port 1 x DisplayPort 1 x RJ-45 port 3 x audio jacks
iTE® I/O Controller Chip
Voltage detection Temperature detection Fan speed detection
Water cooling flow rate detection Fan fail warning Fan speed control

• Whether the fan (pump) speed control function is supported will depend on the fan
  (pump) you install.

j Only for Z790 D AX. k Only for Z790 D AC.
– 9 –

BIOS

Unique Features

Bundled

Software

Operating

System

Form Factor

1 x 256 Mbit flash Use of licensed AMI UEFI BIOS PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0 Support for GIGABYTE Control Center (GCC)

• Available applications in GCC may vary by motherboard model. Supported functions of each application may also vary depending on motherboard specifications.
  Support for Q-Flash Support for Q-Flash Plus Support for Smart Backup Norton® Internet Security (OEM version) LAN bandwidth management software Support for Windows 11 64-bit Support for Windows 10 64-bit
  ATX Form Factor; 30.5cm x 24.4cm

• GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

& Please visit the SERVICE/SUPPORTUtility page on GIGABYTE’s website to download the latest version of apps. https://www.gigabyte.com/Support/Utility/Motherboard?m=ut
– 10 –

2-3 Installing the CPU and CPU Cooler
Read the following guidelines before you begin to install the CPU: · Make sure that the motherboard supports the CPU.
(Go to GIGABYTE’s website for the latest CPU support list.) · Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage. · Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.) · Apply an even and thin layer of thermal grease on the surface of the CPU. · Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur. · Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.
A. Note the CPU Orientation
Note the alignment keys on the motherboard CPU socket and the notches on the CPU.
Alignment Key

Triangle Pin One Marking of the CPU Socket

LGA1700 CPU Socket
Alignment Key Notch

Triangle Pin One Marking on the CPU

LGA1700 CPU
Notch

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate automatically after you insert the CPU and close the load plate.

& Please visit GIGABYTE’s website for details on hardware installation. https://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw
– 11 –

B. Installing the CPU
Follow the steps below to correctly install the CPU into the motherboard CPU socket.

u

Finger Tab

jGently press the CPU socket lever handle down and away from the socket.
kCompletely lift up the CPU socket locking lever.
lUse the finger tab on the side of the metal load plate to lift open the metal load plate with the plastic protective cover attached to it.

l k

j

v
Hold the CPU with your fingers by the edges. Align the CPU pin one marking (triangle) with the pin one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently insert the CPU into position.

Pin One

w
j
Make sure the CPU is properly installed and

then close the load plate. The plastic protec-

tive cover will pop off, just remove it. Secure

the lever under its retention tab to complete

the installation of the CPU. * Always replace the plastic protective cover

k

when the CPU is not installed to protect the CPU socket.

l

Do not force to engage the CPU socket locking lever when the CPU is not installed correctly as this would damage the CPU and CPU socket.
– 12 –

C. Installing the CPU Cooler
Be sure to install the CPU cooler after installing the CPU. (Actual installation process may differ depending the CPU cooler to be used. Refer to the user’s manual for your CPU cooler.)
u
Apply an even and thin layer of thermal grease on the surface of the installed CPU.

v
Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Push down on the push pins diagonally.

j k
k
j

w
Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard.

– 13 –

CPU_FAN

2-4 Installing the Memory
Read the following guidelines before you begin to install the memory: · Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used. (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.) · Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. · Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The four memory sockets are divided into two channels and each channel has two memory sockets as following: Channel A: DDR5_A1, DDR5_A2 Channel B: DDR5_B1, DDR5_B2

• Recommended Dual Channel Memory Configuration:

DDR5_A1

DDR5_A2

DDR5_B1

2 Modules

– –

DS/SS

– –

4 Modules

DS/SS

DS/SS

(SS=Single-Sided, DS=Double-Sided, “- -“=No Memory)

DS/SS

DDR5_B2 DS/SS DS/SS

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled if only one memory module is installed. 2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of
the same capacity, brand, speed, and chips be used.

DDR5_A1 DDR5_A2 DDR5_B1
DDR5_B2
When installing a single memory module, we recommend that you install it in the DDR5_A2 socket.
– 14 –

2-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card: · Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card. · Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage. Follow the steps below to correctly install your expansion card in the expansion slot. 1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel. 2. Align the card with the slot, and press down on the card until it is fully seated in the slot. 3. Make sure that the expansion card is fully seated in its slot. 4. Secure the card’s metal bracket to the chassis back panel with a screw. 5. After installing all expansion cards, replace the chassis cover(s). 6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your
expansion card(s). 7. Install the driver provided with the expansion card in your operating system.
PCIEX16 Slot
– 15 –

2-6 Back Panel Connectors
jk
USB 2.0/1.1 Port (Q-Flash Plus Port) The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices. Before using Q-Flash Plus , (Note) make sure to insert the USB flash drive into this port first. USB 2.0/1.1 Port The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices. PS/2 Keyboard/Mouse Port Use this port to connect a PS/2 mouse or keyboard. SMA Antenna Connectors (2T2R)jk Use this connector to connect an antenna.
Tighten the antennas to the antenna connectors and then aim the antennas correctly for better signal reception. USB 3.2 Gen 1 Port The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0 specification. Use this port for USB devices. DisplayPort DisplayPort delivers high quality digital imaging and audio, supporting bi-directional audio transmission. DisplayPort can support the HDCP 2.3 content protection mechanism. You can use this port to connect your DisplayPort-supported monitor. Note: The DisplayPort Technology can support a maximum resolution of 4096×2304@60 Hz but the actual resolutions supported depend on the monitor being used. HDMI Port
The HDMI port is HDCP 2.3 compliant and supports Dolby TrueHD and DTS HD Master Audio formats. It also supports up to 192KHz/24bit 7.1-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096×2160@60 Hz, but the actual resolutions supported are dependent on the monitor being used. After installing the DisplayPort/HDMI device, make sure to set the default sound playback device to DisplayPort/HDMI. (The item name may differ depending on your operating system.)
j Only for Z790 D AX. k Only for Z790 D AC.
(Note) To enable the Q-Flash Plus function, please navigate to the “Unique Features” page of GIGABYTE’s website for more information.
– 16 –

USB 3.2 Gen 2 Type-A Port (Red) The USB 3.2 Gen 2 Type-A port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1 and USB 2.0 specification. Use this port for USB devices.
USB Type-C® Port (with USB 3.2 Gen 2 Support) The reversible USB port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 2, USB 3.2 Gen 1, and USB 2.0 specifications. Use this port for USB devices.
RJ-45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 2.5 Gbps data rate. The following describes the states of the LAN port LEDs.

Speed LED Activity LED LAN Port

Speed LED:
State Orange Green Off

Description 2.5 Gbps data rate 1 Gbps data rate 100 Mbps data rate

Activity LED:
State Blinking Off

Description Data transmission or receiving is occurring No data transmission or receiving is occurring

Line In/Rear Speaker Out The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc. Line Out/Front Speaker Out The line out jack. Mic In/Center/Subwoofer Speaker Out The Mic in jack.

Audio Jack Configurations:
Jack
Line In/Rear Speaker Out Line Out/Front Speaker Out Mic In/Center/Subwoofer Speaker Out Front Panel Line Out/Side Speaker Out

Headphone/ 2-channel
a

4-channel a a

5.1-channel
a a a

7.1-channel
a a a a

You can change the functionality of an audio jack using the audio software. To configure 7.1-channel audio, access the audio software for audio settings.
& Please visit GIGABYTE’s website for details on configuring the audio software. https://www.gigabyte.com/WebPage/697/realtek897-audio.html

· When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
· When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
– 17 –

2-7 Onboard Buttons and LEDs
Quick Button The reset button allows users to quickly turn on/off the computer in an open-case environment when they want to change hardware components or conduct hardware testing.

RST_SW
The reset button provides you with several functions to use. To remap the button to perform different tasks, please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “RST_SW (MULTIKEY)” for more information.
QFLASH_PLUS (Q-Flash Plus Button) Q-Flash Plus allows you to update the BIOS when your system is off (S5 shutdown state). Save the latest BIOS on a USB thumb drive and plug it into the dedicated port, and then you can now flash the BIOS automatically by simply pressing the Q-Flash Plus button. The QFLED will flash when the BIOS matching and flashing activities start and will stop flashing when the main BIOS flashing is complete.
QFLED
QFLASH_PLUS

QFLASH_PLUS

QFLED

To enable the Q-Flash Plus function, please navigate to the “Unique Features” page of GIGABYTE’s website for more information.

– 18 –

Status LEDs The status LEDs show whether the CPU, memory, graphics card, and operating system are working properly after system power-on. If the CPU/DRAM/VGA LED is on, that means the corresponding device is not working normally; if the BOOT LED is on, that means you haven’t entered the operating system yet.
CPU: CPU status LED DRAM: Memory status LED VGA: Graphics card status LED BOOT: Operating system status LED
CPU DRAM VGA BOOT
– 19 –

2-8 Internal Connectors

41

3 67

2

4

14

9

13

17 9

9

8

19

11 12

7 16 15

5 20 18 10

1. ATX_12V_2X4_1/2 2) ATX 3) CPU_FAN 4) SYS_FAN1/SYS_FAN2A/2B 5) SYS_FAN3_PUMP

2. CPU_OPT 7) D_LED1/D_LED2 8) SATA3 4/5/6/7 9) M2A_CPU/M2P_SB/M2M_SB 10) F_PANEL

3. F_AUDIO 12) SPDIF_O 13) F_U32C 14) F_U32 15) F_USB1/F_USB2 16) SPI_TPM 17) THB_C1/THB_C2 18) CLR_CMOS 19) BAT 20) RST

Read the following guidelines before connecting external devices: · First make sure your devices are compliant with the connectors you wish to connect. · Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices. · After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
– 20 –

1/2) ATX_12V_2X4_1/2/ATX (2×4 12V Power Connectors and 2×12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

ATX_12V_2X4_1

ATX_12V_2X4_2

ATX

5

8

1

4

ATX_12V_2X4_1/2

12

24

1

13

ATX

ATX_12V_2X4_1/2:

Pin No. Definition

Pin No.

1 GND (Only for 2×4-pin 12V) 5

2 GND (Only for 2×4-pin 12V) 6

3 GND

7

4 GND

8

Definition +12V (Only for 2×4-pin 12V) +12V (Only for 2×4-pin 12V) +12V +12V

ATX:
Pin No. 1 2 3 4 5 6 7 8 9 10 11
12

Definition

Pin No.

3.3V

13

3.3V

14

GND

15

+5V

16

GND

17

+5V

18

GND

19

Power Good

20

5VSB (stand by +5V)

21

+12V

22

+12V (Only for 2×12-pin 23 ATX) 3.3V (Only for 2×12-pin 24 ATX)

Definition 3.3V -12V GND PS_ON (soft On/Off) GND GND GND NC +5V +5V +5V (Only for 2×12-pin ATX)
GND (Only for 2×12-pin ATX)

– 21 –

3/4) CPU_FAN/SYS_FAN1/SYS_FAN2A/2B (Fan Headers) All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

SYS_FAN1

CPU_FAN

SYS_FAN2B SYS_FAN2A

1 CPU_FAN

CPU_FAN/SYS_FAN1/SYS_FAN2A:
Pin No. Definition 1 GND 2 Voltage Speed Control 3 Sense 4 PWM Speed Control

1 SYS_FAN1/SYS_FAN2A/2B

SYS_FAN2B:
Pin No. Definition 1 GND 2 Voltage Speed Control 3 NC 4 PWM Speed Control

5. SYS_FAN3_PUMP (System Fan/Water Cooling Pump Header)
   The fan/pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. The header also provides speed control for a water cooling pump. Please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “Smart Fan 6” for more information.

Pin No. Definition

1 GND

1

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

SYS_FAN3_PUMP
· Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
· These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
– 22 –

6. CPU_OPT (CPU Fan/Water Cooling Pump Header)

The fan/pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a

foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation

(the black connector wire is the ground wire). The speed control function requires the use of a fan with fan

speed control design.

CPU_OPT

Pin No. Definition

1

1 GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

Connector Maximum Current Maximum Power

CPU_FAN 2A 24W

SYS_FAN1/2A/2B 2A 24W

SYS_FAN3_PUMP 2A 24W

CPU_OPT 2A 24W

7. D_LED1/D_LED2 (Addressable LED Strip Headers) The headers can be used to connect a standard 5050 addressable LED strip, with maximum power rating of 5A (5V) and maximum number of 1000 LEDs.
   D_LED2

1 D_LED2
1 D_LED1

Pin No. 1 2 3 4

Definition V (5V) Data No Pin GND

Addressable LED Strip

D_LED1

Connect your addressable LED strip to the header. The power pin (marked

1

with a triangle on the plug) of the LED strip must be connected to Pin 1 of the

addressable LED strip header. Incorrect connection may lead to the damage

of the LED strip.

For how to turn on/off the lights of the LED strip, please navigate to the “Unique Features” page of GIGABYTE’s website.

Before installing or removing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.

– 23 –

8. SATA3 4/5/6/7 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel® Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Please navigate to the “Configuring a RAID Set” page of GIGABYTE’s website for instructions on configuring a RAID array.
   G.QBOFM G.QBOFM G.QBOFM

7

1

7

1

SATA3 5 7 46

Pin No. 1 2 3 4 5 6 7

Definition GND TXP TXN GND RXN RXP GND

7 6

5 4

SATA3

To enable hot-plugging for the SATA ports, please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “SATA Configuration” for more information.

– 24 –

9. M2A_CPU/ M2P_SB/ M2M_SB (M.2 Socket 3 Connectors) There are two types of M.2 SSDs: M.2 SATA SSDs and M.2 PCIe SSDs. Be sure to verify the type of M.2 SSDs you want to use. Please note that an M.2 PCIe SSD cannot be used to create a RAID set with SATA hard drive. Please navigate to the “Configuring a RAID Set” page of GIGABYTE’s website for instructions on configuring a RAID array.

110

80

M2A_CPU

80
M2A_CPU M2P_SB M2M_SB
80

M2P_SB M2M_SB

Follow the steps below to correctly install an M.2 SSD in the M.2 connector. Step 1: Locate the M.2 connector where you will install the M.2 SSD, use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink. (Only the M2A_CPU connector has the heatsink.) Remove the protective film from the thermal pad on the M2A_CPU connector. Step 2: Locate the proper mounting hole for the M.2 SSD to be installed. Insert the M.2 SSD into the M.2 connector at an angle. Step 3: Press the M.2 SSD down and then use the included screw to secure it in the connector. Replace the heatsink and secure it to the original hole. Remove the protective film from the bottom of the heatsink before replacing the heatsink.

• Types of M.2 SSDs supported by each M.2 connector:

M.2 PCIe x4 SSD M.2 PCIe x2 SSD

M2A_CPU

a

a

M2P_SB

a

a

M2M_SB

a

a

M.2 SATA SSD r r a

– 25 –

10. F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
    Power LED Power Switch Speaker

PLED+ PLED-
PW+ PWSPEAK+ NC NC SPEAK-

G.QBOFM

2

20

1

19

HD+ HD-
RESCI-RES+ CI+
PWR_LED+ PWR_LEDPWR_LED-

F_PANEL

Hard Drive Reset Activity LED Switch

Power LED

Chassis Intrusion Header

· PLED/PWR_LED (Power LED):

System Status LED Connects to the power status indicator on the chassis front panel. The LED

S0

On

S3/S4/S5

Off

is on when the system is operating. The LED is off when the system is in S3/ S4 sleep state or powered off (S5).

· PW (Power Switch): Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “Soft-Off by PWR-BTTN” for more information).
· SPEAK (Speaker): Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.
· HD (Hard Drive Activity LED): Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
· RES (Reset Switch): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
· CI (Chassis Intrusion Header): Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.
· NC: No Connection.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
– 26 –

11. F_AUDIO (Front Panel Audio Header) The front panel audio header supports High Definition audio (HD). You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

F_AUDIO

9

1

10

2

Pin No. 1 2 3 4 5 6 7 8 9 10

Definition MIC L GND MIC R NC Head Phone R MIC Detection SENSE_SEND No Pin Head Phone L Head Phone Detection

Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

12. SPDIF_O (S/PDIF Out Header) This header supports S/PDIF digital output, which allows you to connect a S/PDIF digital audio cable to output digital audio from your motherboard to the supported audio devices. For information about connecting the digital audio cable, carefully read the manual for your audio devices.

Pin No. Definition

1 5VDUAL

2 No Pin

1

3 SPDIFO

4 GND

SPDIF_O

– 27 –

13. F_U32C (USB Type-C® Header, with USB 3.2 Gen 1 Support) The header conforms to USB 3.2 Gen 1 specification and can provide one USB port.

10

11

1

20

F_U32C

Pin No. 1 2 3 4 5 6 7 8 9 10

Definition VBUS TX1+ TX1GND RX1+ RX1VBUS CC1 SBU1 SBU2

Pin No. 11 12 13 14 15 16 17 18 19 20

Definition VBUS TX2+ TX2GND RX2+ RX2GND DD+ CC2

14. F_U32 (USB 3.2 Gen 1 Header) The header conforms to USB 3.2 Gen 1 and USB 2.0 specification and can provide two USB ports. For purchasing the optional 3.5″ front panel that provides two USB 3.2 Gen 1 ports, please contact the local dealer.

20
F_U32 11

Pin No. Definition

1

1 VBUS

2 SSRX1-

3 SSRX1+

4 GND

5 SSTX1-

6 SSTX1+
10
7 GND

8 D1-

9 D1+

10 NC

Pin No. 11 12 13 14 15 16 17 18 19 20

Definition D2+ D2GND SSTX2+ SSTX2GND SSRX2+ SSRX2VBUS No Pin

– 28 –

15. F_USB1/F_USB2 (USB 2.0/1.1 Headers) The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

F_USB2

F_USB1

Pin No. Definition

1 Power (5V)

2 Power (5V)

3 USB DX-

9

1

10

2

4 USB DY5 USB DX+

6 USB DY+

7 GND

8 GND

9 No Pin

10 NC

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.

16. SPI_TPM (Trusted Platform Module Header) You may connect an SPI TPM (Trusted Platform Module) to this header.

SPI_TPM

Pin No. Definition

1 Data Output

2 Power (3.3V)

11

1

12

2

3 No Pin 4 NC

5 Data Input

6 CLK

7 Chip Select

8 GND

9 IRQ

10 NC

11 NC

12 RST

– 29 –

17. THB_C1/THB_C2 (ThunderboltTM Add-in Card Connectors) The connectors are used to connect to a GIGABYTE ThunderboltTM add-in card.

1 THB_C2

THB_C2 THB_C1

1 THB_C1

Supports a ThunderboltTM add-in card.
18) CLR_CMOS (Clear CMOS Jumper) Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
Open: Normal Short: Clear CMOS Values
CLR_CMOS
· Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.
· After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (please navigate to the “BIOS Setup” page of GIGABYTE’s website for more information).
– 30 –

19. BAT (Battery) The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery: 1. Turn off your computer and unplug the power cord. 2. Gently remove the battery from the battery holder and wait for one minute.
(Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.) 3. Replace the battery. 4. Plug in the power cord and restart your computer.
BAT
· Always turn off your computer and unplug the power cord before replacing the battery. · Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model. · Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model. · When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up). · Used batteries must be handled in accordance with local environmental regulations.
20) RST (Reset Jumper) The reset jumper can connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

1

Pin No. Definition

1 Reset

2 GND

RST
The reset jumper provides you with several functions to use. To remap the button to perform different tasks, please navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “RST_SW (MULTIKEY)” for more information.
– 31 –

Chapter 3 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS. To access the BIOS Setup program, press the key during the POST when the power is turned on. To upgrade the BIOS, use either the GIGABYTE Q-Flash or Q-Flash Plus utility.
· Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system. · Q-Flash Plus allows you to update the BIOS when your system is off (S5 shutdown state). Save the latest
BIOS on a USB thumb drive and plug it into the dedicated port, and then you can now flash the BIOS automatically by simply pressing the Q-Flash Plus button. For instructions on using the Q-Flash and Q-Flash Plus utilities, please navigate to the “Unique Features” page of GIGABYTE’s website and search for “BIOS Update Utilities.”
· Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.
· It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system’s failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
· Refer to the introductions of the battery/clear CMOS jumper in Chapter 2 or navigate to the “BIOS Setup” page of GIGABYTE’s website and search for “Load Optimized Defaults” for how to clear the CMOS values.
& Please visit GIGABYTE’s website for details on configuring BIOS Setup. https://www.gigabyte.com/WebPage/928/intel700-bios.html
– 32 –

Startup Screen: The following startup Logo screen will appear when the computer boots.
Function Keys
Function Keys: : BIOS SETUPQ-FLASH
Press the key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup. : BOOT MENU
Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up arrow key or the down arrow key to select the first boot device, then press to accept. The system will boot from the device immediately. Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order will still be based on BIOS Setup settings. : Q-FLASH Press the key to access the Q-Flash utility directly without having to enter BIOS Setup first.
– 33 –