PARRIOR SD-840M Cordless Hot Glue Gun Instructions
- June 17, 2024
- PARRIOR
Table of Contents
MOTOR DRIVEN
CORDLESS GLUE GUNPARRIOR GG03
Before you use the appliance, please read this user manual carefully and store it in a safe place for future reference.
SAFETY INSTRUCTIONS
- Do not put the glue gun sideways.
- Before use, please prepare a piece of paper or cardboard and place it on the workbench, prevent damage caused by hot glue dripping.
- During heating and within half an hour after shutdown, do not touch the nozzle.
- Please use the glue gun in a well-ventilated place, avoid breathing hot glue vapor.
- Do not aim the nozzle of the glue gun at others or animals.
- Do not use the glue gun with the nozzle tilted upwards.
- The next step of processing must be carried out after the hot glue is completely cooled and solidified, avoid scalding.
- Except for the standard glue stick, do not insert anything into the glue inlet.
- When inserting a new glue stick, do not put your hands or fingers near the nozzle.
- When the glue gun is turned on, must be watched over.
- Not allowed to use glue gun under the age of 8.
PRODUCT DESCRIPTION AND SPECIFICATIONS
I NTENDED USE:
The glue gun is suitable for bonding paper, paperboard, cork, wood, leather,
textile, foam materi als, plastics (except PE, PP, polytetrafluoroethylene,
foam polystyrene and plasticized PVC), pottery, porcelain, metal, glass, stone
and other materials.
PRODUCT DESCRIPTION:
- Nozzle
- LED light
- Silicone cap
- Trigger
- Switch
- Indicator
- Glue stick
- Charging socket
- harge socket indicator
- USB charging cable
TECHNICAL SPECIFICATIONS
| Voltage | 4V |
|---|---|
| Power | 20W |
| Warm-Up Time | 15 ± 5 seconds |
| Heating Temperature | 155±10°C |
| Battery Capacity | 4000mAh |
| Using Time | 40-60 minutes |
| Charging Time | 3.5 hours |
| Automatic Power-off Time | 5 minutes |
| Applicable Glue Stick Diameter | 7.0±0.3mm |
USAGE
PREPARATIONS FOR GLUING
- Clean the surface before bonding, make sure surface is clean, dry and free of grease. Do not use flammable solvents for cleaning! Keep the ambient temperature and object within the range of+S °C-+S0°C. Heat the surface of a cryogenic object, such as steel, for better adhesion.
- Before use, please prepare a piece of paper or cardboard and place it on the workbench, prevent the hot glue from dropping on the work surface and causing damage.
SWITCH ON AND OFF
- In the shutdown state, press and hold the switch for 3s to start the machine, the glue gun starts to heat, and the indicator flashes red.
- After about 1 Ss of a startup, the green indicator is always on, the glue gun is preheated.
- When the machine s started, press and hold the switch for 2s, the glue gun stops heating, and the ndicator ight goes out.
- After stopping use for 5 minutes, automatic shutdown.
GLUING
- Insert the glue stick after preheating.
- Press the trigger to apply glue on the surface, keep pressing the trigger continuously to release glue, no need to pull the trigger repeatedly, release glue more evenly and smoothly, after the trigger is released, the glue stick automatically returns and absorbs residual glue.
- After applying the adhesive, press the objects together for about 1 Oto 30 seconds, until the hot glue is completely cooled and solidified. During this time, the bonding position can still adjust.
CHANGE GLUE STICKS
Do not pull the unused glue stick out of the glue gun, in case of a forced
pullout, the glue gun may be damaged. If you need to replace different types
of glue sticks, please finish the old glue stick before inserting a new glue
stick.
CHARGING
- Mode 1: Connect the USB charging cable directly through the charging port at the bottom of the glue gun for charging.
- Mode 2: Connect the charging socket with the USB charging cable, place the glue gun on the charging socket to charging.
- The red indicator is always on when charging, and the green ndicator is always on when the battery is fully charged, the full charge time is about 3.5 hours.
- When the power is too ow, automatic shutdown after flashing the red indicator for 3 times.
WARM TIPS
- The tip of the nozzle will reach a very high temperature. Do not et the nozzle directly into contact with people or animals. f the hot glue contacts the skin, rinse the affected area with cold water for several minutes immediately. Do not attempt to remove glue from the skin.
- Please place the glue gun on the charging socket or stand upright on the desktop, do not lay it on its side.
MAINTENANCE AND CLEANING
-
It is prohibited to place this product in a high-temperature environment for a long time.
When not n use for a long time, please put the product in a dry environment and at normal atmospheric temperatureroom temperature, to protect the battery life, please charge it every three months. -
Before starting maintenance and cleaning work, please turn off the glue gun.
-
Keep the product surface clean, wipe the surface with a dry soft cloth. Do not use corrosive, irritating detergent cleaning products.
-
To prevent damage to the glue gun, do not pull out the glue stick from the back during using.
ERRORS AND CORRECTIVE MEASURES
| Glue gun cannot be used | Out of battery | Restart after fully charged |
|---|---|---|
| No glue from the nozzle | The glue stick is used up | Insert new glue stick |
| Preheating not completed | Use after preheating | |
| Out of battery | Use after fully charged | |
| The glue stick falls off from the glue inlet | The diameter of glue stick is | |
| too small | Use standard glue stick | |
| The glue stick cannot be inserted into the glue inlet | The diameter of glue | |
| stick is too large | Use standard glue stick | |
| The glue inlet is blocked by foreign matters | Clean the glue inlet | |
| After stopping use, the nozzle still drops glue continuously | Under normal |
conditions, 1-3 drops of glue will fall after stopping use, otherwise the
melting point of glue stick is too low| Use standard glue stick
The glue inlet leaks or blocked| The diameter of glue stick is too small or
the melting point of glue stick is too low| Use standard glue stick
Poor bonding effect| There is oil stain or dust on the bonding surface| Remove
the oil stain and dust on the bonding surface
Improper material of workpiece to be bonded| Please use special glue
After-sale Service: support@parrior.com
Official website: www.parrior.com 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>