BREAKOUT BRK-LBMI Wireless LED Karaoke Mic User Guide
- August 9, 2024
- BREAKOUT
Table of Contents
BREAKOUT BRK-LBMI Wireless LED Karaoke Mic
HOLLOWED
- DO NOT PRINT
- CUTLINE
- FOLD LINE
- SPOT UV (HIDDEN)
- GLUE
diagram
- mic
- LED lights
- speaker
- karaoke mode: mic on/off
- volume increase; hold for previous song
- press to switch LED mode; hold to switch voice effects
- mic volume decrease; hold for next song
- mic power – hold for on/off; press for play/pause
- micro-usb charging port
- AUX port
- TF card port
contents inside
- LED wireless karaoke mic with built-in speaker
- micro-usb charging cable
- user manual
product specification
- Bluetooth® version: 5.3
- play time: up to 1.5-2.S hours
- speaker output: 3w
- max sound pressure level: >11SdB 1KHz TDH <1%
- bluetooth frequency range: 2402MHz~2480MHz
- reverberation mode: sound effect reverberation
- power supply: built-in 18650 lithium-ion battery
- battery capacity: 800 mAh
- charging interface: micro-usb
- FCC ID, 2AANZBRK-LBMI
power on/ off
- To power on: press and hold 8 for a few seconds.
- To power off: press and hold for a few seconds.
Bluetooth”connect
- Turn on the mic and wait until you hear “Bluetooth® mode.
- Turn on the Bluetooth• on your phone and search for the device; select ‘BRK-LBMI” to connect.
- After connecting, you will hear “Bluetooth connected”.
- The speaker will automatically reconnect your phone the next time it is powered on, on the condition that its Bluetooth! am still on.
pause/play music
Short press8 to pause music while playing
Press8 again to resume play.
volume/track selection
- Short press5 to increase the volume. To decrease volume short press (7
- To skip a song, press and hold7 . To play previous song, press and hold5 .
mic/sound effects
The mic is automatically on, to turn it off press and hold 4 , until you hear
a sound and the lights dim. To turn it back on, press 4 for 2 seconds.
Switch voice effects by holding 6 until you hear Which sound effect is
activated, “doll sound,” “fast sound,” “monster sound/ or “human sound.”
LED light effects
Switch LED light effects by pressing 6 .
safety guidelines
- Please read the instructions carefully before use and keep them for reference.
- Keep in a cool dry place, keep the microphone away from heat and open fire.
- Be sure to hold onto the handle tightly.
- Do not attempt to repair the speaker.
- Do not attempt to use the speaker with AC input, be sure the device is unplugged from power and charged before each use.
troubleshooting
- When the microphone dings during use, battery is low. Turn device off and charge as soon as possible.
- If Bluetooth! will not connect, turn off mic and Bluetooth on your device and be sure to connect in range.
battery care
-
Be sure to charge the microphone fully, before use.
Do not overcharge – Charging takes 2-3 hours, overcharging may severely affect battery life. -
The speaker may lose charge if not used for a long period.
-
Only use the included cable for charging this device.
-
Indicator light will turn red when charging and turn off when fully charged.
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy. If not installed and used by the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
DGL Group, Ltd.
2045 Lincoln Highway, 3rd Fl. Edison, NJ 08817
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>