moisz S5 Robot Vacuum Cleaner User Manual

moisz S5 Robot Vacuum Cleaner

Dear Customer,
Thank you for purchasing NOISZ S5 robot vacuum cleaner! You’ve joined the millions of people who clean with robots – the smarter way to get it down. Please take a few moments to read this manual and get acquainted with your robot, to get the best performance from your robot If you have any problem, please don’t worry, you are supposed to contact our customer seNice first or visit our website at www.iliferobot.com for more information. Stay connected with us on Facebook and twitter to enjoy these exclusive benefits:

• Get support tailored to your specific robot, including answers to questions, maintenance tips, video demos, live chat and more.
• Get product updates and other valuable information about new robots, exclusive discounts and special promotions.

Connect with us right now at

Facebook: facebookcorn/iliferobotics Twitter. twitter.corn/lLIFEROBOTUS Enjoy a thorough clean every day in your life! Best regards, ILIFE Innovation

ILIFE Customer Service

• 1-800-631-9676 (Toll free for USA & Canada) Mon-Fri: 9:00 am – 5:00 pm CST
• support@iliferobot.com

Important Tips

Operate

• Make sure the power switch is turned on before using the robot Check the areas that need to be cleaned and remove obstacles on the floor.
• The robot will repeat cleaning the same areas a few times to ensure they are thoroughly cleaned.
• There may be small particles such as dog food and cat litter scattering on the floor while the spinning brushes are working. The vacuuming function will clear up the debris.
• When replacing the side brushes, make sure they are installed according to the “L” and “R” marks on both sides of the brush and the base of the robot.
• Successful clock and schedule settings will be confirmed by a “beep” sound.
• Empty the dustbin if the robot vacuums less or spits debris out. No alert will be given for a full dustbin.

For best performance

• Empty the dustbin and clean the high-performance filter after each use.
• Filter could not be washed with water.
• Replace the high-performance filter when suctioning power weakens or when the robot picks up less debris.
• Put the charging dock against a wall and remove obstacles about 1 meter on both sides and about 2 meters in front.
• Fully charge the robot before each operation.

Extending battery life

To extend S5’s battery life and keep its cleaning performance at its best:

• Before first use, charge the robot overnight.
• If the robot will not be used for a long time, switch the power off.
• Recharge the robot soon after each use. Robot in low battery status may damage the battery.
• Use the robot regularly.

Warning

• S5 contains electronic parts. Do NOT put it in water or spay it .a with water. Clean the robot with a dry cloth only.

Safety Instructions

Before using the robot, please read and follow the safety instructions and precautions below.

• Read through this user manual carefully before using the robot.
• Retain this user manual.
• Any operation that is not described in this user manual may injure the users and cause product damage.

WARNINGS

1. Only certified technicians may disassemble the robot. Users must not disassemble or repair the robot.
2. Use factory-authorized adapter only. Using a nonspecific adapter may cause electric shock, fire or robot damage.
3. Do not touch the power cord, plug or adapter with wet hands.
4. Do not allow clothes or any part of your body to be drawn into the robot’s wheels.
5. Do not place the robot near cigarettes, lighters, matches or other flammables.
6. Clean the robot after charging finishes.
7. Do not over-bend the power cord or pressure the power cord with heavy or sharp objects.
8. Do not use the robot outdoors.
9. Do not sit on the robot or attach any object to it.
10. Do not use the robot on wet floors.
11. Before using the robot, remove all fragile objects (textiles, glass, lighting, etc) and other objects that could get caught in the brushes or suction opening (cords, clothing, papers, drapes, blinds, etc) on the floor.
12. Do not place the robot where it could easily fall off (tables, chairs, etc).
13. Turn off the power switch during transportation or when the robot will not be used for a long time.
14. To avoid battery damage, check if the adapter and outlet are properly connected before using the robot.
15. To avoid tripping, make sure everyone in the house knows the robot is working.
16. Use the robot in an environment between -10° and 40° Celsius.
17. Do not place the robot in a high-temperature environment.
18. Before scrapping the battery, remove it from the robot.
19. Disconnect electricity supply before removing the battery.
20. The battery is to be disposed of safely according to local regulations.

NOTE: This robot should not be used by children, mentally challenged people or people who lack related experience and knowledge (unless they are under proper supervision).

Product Parts

Main body and accessories

Robot anatomy

Dustbin

Charging dock

Remote control

Remote control operation

Start/Pause

• To start cleaning in the selected mode.
• To stop the current cleaning cycle.
• To change from sleep mode to selected mode.

Direction Buttons

” ” Button

• To increase minute and hour settings in schedule or clock mode.
• To move the robot forward in the selected mode.
• To stop the robot when it hits against objects.

“MAX” Button

• To decrease minute and hour settings in schedule or clock mode.
• To move the robot backward in the selected mode.
• Press “MAX”, the vacuum power will be the strongest.

C. ” ◄ ” Button

• To change from minute to hour in schedule or clock mode.
• To turn the robot left.

D. ” ► ” Button

• To change from minute to hour in schedule or clock mode.
• To turn the robot right.

Plan

• To enter schedule mode when the robot is in the selected mode.
• To confirm scheduled cleaning.

Clock

• To enter clock mode when the robot is in the selected mode.
• To confirm time setting.

Auto charge button

• To return the robot to the charging dock.

Edge button

• To clean along the edge of the walls.

Spot button

• To start cleaning specific areas.
• To display scheduled time.
•  To display clock.

Note

1. Place two AAA batteries into the remote control.
2. Remove batteries if the remote control will not be used for a long time.

CLEAN button signals

Product Operation

Getting started

1. Place the charging dock on the floor and plug in the adapter. The signal light on the charging dock will turn solid.
   Note: Put charging dock against a wall and remove obstacles about 1 meter on both sides and about 2 meters in front.

2. The display panel will flash after the power switch (near the power socket) is turned on. (If no command is received, the robot will switch to sleep mode after 45 seconds.)
   Note: A. Always keep the power switch on, otherwise the robot will not work. B. If the power switch is turned off, all scheduled cleaning will be lost.
   Caution: Before charging the robot, make sure the power switch is turned on, or the robot will not be charged.

Robot can be recharged by

• A. plugging into an outlet;
• B. pressing button on the remote control – the robot will return to the charging dock for auto recharge.

Extending battery life

• A. Before first use, charge the robot overnight. When charging is finished, the light at the main button will turn off.
• B. Always place the robot on a charging dock that is connected to power.
• C. If the robot will not be used for a long time, fully recharge the robot and turn the power switch off before storing it in a cool, dry place.

Auto charging
The robot will automatically return to the charging dock when its battery runs low.

Start/Pause/Sleep

• Sleep mode: robot is not working, light at button is off and power switch is on.
• Selected mode: robot is not working, green light at  button flashes.
• Cleaning mode: robot is working, green light at  button turns solid.

Start

• A. Make sure the power switch is turned on.
• B. Press button on robot or remote control to start cleaning.

Note: If robot is in sleep mode, press button to reactivate it. Press button again to start the operation.

Pause
Press button on robot or remote control to change robot from Clean mode to selected mode.

Note: When robot is paused, press button to resume the operation.

Sleep
To switch the robot from selected mode to sleep mode:

• Press and hold button on robot for 3 seconds.
• Robot automatically enters sleep mode if no command is received after 15 seconds.

Schedule

You can preset a cleaning routine for your robot.

Note: Reset the clock and reschedule a cleaning cycle after replacing battery. Robot will only start cleaning automatically after the clock and schedule are set.

Set the clock

1. Point the remote control at the robot (make sure the power switch is on).
2. Press button and adjust to your local time with direction buttons.
3. Press button again to save the setting.

Set a schedule
Robot starts a cleaning schedule only when its power switch is on.

1. Point the remote control at robot.
2. Press button and adjust time with direction buttons.
3. Press button to save the setting.

Note

1. Successful clock and schedule settings will be confirmed by a “beep” sound. Reset the schedule if there is no sound confirmation.
2. Turn off the robot to cancel the schedule.

Cleaning modes

Auto cleaning
In Auto Cleaning mode, the robot automatically cleans the areas it can reach.

Note: Press button on the robot or remote control to start Auto Cleaning.

Spot cleaning

• Point remote control at robot and press button while it is cleaning. Robot will clean around a circular route and return to Auto Clean mode after Spot cleaning is finished.
• Point remote control at robot and press button when robot is in selected mode. The robot will clean around a circular route and return to selected mode after Spot cleaning is finished.

Edge cleaning
To start edge cleaning, put the robot near the edge of a wall and press button on the remote control.

Note: Edge cleaning will automatically stop if the robot cannot detect any edges. To stop edge cleaning manually, press button.

MAX cleaning
High suction power for areas with concentrated dust. Press the MAX button on the remote control to increase the suction level. Press MAX again to return to normal level.

Electrowall

Electrowall creates an invisible barrier that S5 will not cross. This invisible barrier can be used to confine S5 to a particular room or area.

• Install battery first, then turn it on.
• Put the Electrowall on the outside of the doorway you wish to block.
• Ensure the signal logo is facing forward and toward the opening you would like to block.
• Turn off the Electrowall after each use.

TIPS

• Make sure which side is the working area according to the stickers on the Electrowall.
• Place the robot in the “working area” to do the cleaning.
• We suggest putting the Electrowall behind the door or against the wall.

Maintenance

Side brushes
Clean the side brushes when they get dirty. Replace them if they are damaged. Note: When replacing the side brushes, make sure they are installed according to the “L” and “R” marks on both sides of the brush and the base of the robot.

Dustbin and filter
Follow the below steps to empty and clean the dustbin after each use.

• Take out the dustbin and clean dust or debris in the suction opening.
• Clean the high-performance filter after 15-30 days of use. Replace it with no more than 6 months of use.
• Do not reinstall the high-performance filter and primary filters when they are still wet.
• Replace the high-performance filter and primary filter if needed.

Cliff sensors and auto-charging pins
Gently clean the sensor lens and auto charging pins with a soft dry cloth. Note: Charging pins need to be cleaned if they become dirty.

Nose wheel

Make sure the nose wheel is clean to avoid lowered cleaning performance:

1. Pull the wheel up and out vertically and clean it. Also check if the gasket is worn.
2. Ensure that the gasket is properly installed after cleaning the nose wheel.

Troubleshooting

Error codes
The robot will remind you by beeping when it is malfunctioning.

Short tones

Note: If none of the above solutions works, try the following:

1. Turn power switch off and on to reset the robot.
2. If resetting doesn’t help, contact the seller for repair service.

Error symptoms

Circle around a small area

| ****

The side wheels are jammed

| ****

–  Remove hair and debris from side wheels

– While reinstalling, push the wheels in and out to make sure they can rotate freely

–  Restart the robot in another spot

Keep moving backward| A Cliff sensor is dirty or broken| Check cliff sensor lens Clean or replace it if needed
Bump into obstacles repeatedly| The bumper is stuck| – Tap the bumper 10-20 times to remove debris lodged in it

–  Loosen the screw of the bumper

Working time shortened| –  Battery capacity dropped

–  Robot is not fully charged

| –  Replace battery

–  Recharge robot

CLEAN

button light is off while charging

| – Hair or small debris stuck in charging pins

–  Robot is not properly

connected to charging pins

| – Clean charging pins

– Check if the robot is connected to charging pins

Pick up less dirt and debris| The filter is dirty or wet| Clean or replace the filter
Spit out litter| Dustbin is full| Empty the dustbin
The robot doesn’t start at the scheduled time| The schedule was not saved successfully

– Schedule was cancelled after you restarted the robot

–  Power Switch is off

–  Battery is low

– Debris jammed in components

| – Reset schedule. Wait for a beep to confirm the completion of the scheduling

– Turn on the power switch on the robot

– Keep the robot’s power switch on and put it on the charging dock to make sure the robot is fully charged for the next job

– Turn off the power switch on the robot and empty the dustbin

– Clean side brushes and main brushes

Mechanical

| Diameter| 300mm
Height| 77mm
Net weight| 2.16kg

Electrical

| Battery type| Li-ion
Power| 22W
Charging type| Auto/ Manual

Cleaning

| Capacity of dustbin| 0.3 L
Cleaning modes| Auto/Spot/Edge/MAX
Duration per recharge| <300 mins
Duration per cleaning| > 90 mins
Main Body Button| Mechanical Button

Remark: The storage temperature of this product is between -10°C and 40°C.

ILIFE Customer Service

• 1-800-631-9676 (Toll free for USA & Canada) Mon-Fri: 9:00 am – 5:00 pm CST
• support@iliferobot.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>