DREAME H12 Dual Wet and Dry Vacuum User Manual
- June 17, 2024
- dreame
Table of Contents
Dreame H12 Dual
Wet and Dry Vacuum
User Manual
H12 Dual Wet and Dry Vacuum
The illustrations in this manual are for reference only.
Please refer to the actual product.
THANK YOU
FOR PURCHASING THIS DREAME WET AND DRY VACUUM.
Registration Quick Start
Welcome to register a Dreame account by scanning the QR code. You are
available for the User Manual and Special Offers.
https://www.dreame-technology.com/pages/dreame-care
With it you are obtaining a high quality product that is engineered for
optimal performance.
If you have any questions on the product, please contact us:
aftersales@dreame.tech.
Important Safety Instructions
Please read this manual carefully before use and retain it for future
reference. When using an electrical appliance, basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
WARNING — To reduce the risk of fire, electric shock, or injury:
Usage Restrictions
- This appliance should not be used by children younger than 8 years old nor persons with physical, sensory, intellectual deficiencies, or limited experience or knowledge without the supervision of a parent or guardian to ensure safe operation and to avoid any risks. Cleaning and maintenance shall not be performed by children without supervision.
- Plastic film can be dangerous. To avoid the danger of suffocation, keep it away from children.
- Use indoors only, on non-carpeted floor surfaces such as vinyl, tile, sealed wood, etc. Be careful not to run over loose objects or the edges of area rugs. Stalling the brush may result in premature belt failure.
- Use only as described in this user guide. Use only manufacturer’s recommended attachments.
- Do not expose the appliance to fire or excessive temperature. Exposure to fire or excessive temperature may cause an explosion.
- Do not use in extremely hot or cold environments (below 5°C /41°F or above 40°C /104°F). Please charge the appliance in temperature above 5°C /41°F and below 40°C /104°F).
- Do not immerse the appliance in liquid.
- Do not use to pick up flammable or combustible liquids, such as gasoline. Do not use in areas where flammable or combustible liquids may be present.
- Do not put any object into openings. Do not use the appliance when any opening is blocked. Keep free of dust, lint, hair, and anything that may inhibit air flow.
- Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.). Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
- Do not use the appliance in an enclosed space filled with vapor given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapour. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
- Do not use the appliance without filters in place.
- Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts of the appliance and its accessories.
- Keep ground cables away from the appliance when using it. A hazard may occur if the appliance runs over a supply cord.
- Use extra care when cleaning on stairs.
Important Safety Instructions
Maintenance and Storage
- Prevent unintentional starting. Ensure the switch is in the OFF-position before picking up or carrying the appliance. Carrying the appliance with your finger on the switch or turning on the appliance may result in an accident.
- Ensure that the appliance is placed on a horizontal surface. Do not use the appliance at the same position if the appliance is equipped with a brush roller and the handle is not completely upright. Do not store the appliance in a place where it may freeze.
- Switch off and unplug the appliance when not in use, before cleaning, maintaining or servicing it, and before connecting or disconnecting it with a moving brush.
- Do not use an appliance that is damaged or modified. A damaged or modified appliance may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
- Do not modify or attempt to repair the appliance except as indicated in the instructions for use and care.
- Do not use the appliance with a damaged attachment (eg: charging base, supply cord etc.). If the appliance or attachment has been dropped, damaged, left outdoors, dropped into water, or is not working as it should, never attempt to operate it. Please have it repaired at an authorized service center.
- Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the appliance is maintained.
Battery and Charging
- For the purpose of recharging the appliance, only use the charging base provided with this appliance. Use only with HCB3/HCB6 charging base.
- Follow all charging instructions and do not charge the appliance outside of the temperature range specified in the battery as doing so increases the risk of fire.
- Charging base is equipped with drying function and only suitable for drying this appliance’s brush.
- Keep the charging base cable away from heated surfaces. Do not handle the charging base plug or appliance with wet hands. To unplug, grasp the charging base plug, rather than the cable.
- Do not pull or carry charging base by cable, use cable as a handle, close door on cable, or pull cable around sharp edges or corners.
- This appliance contains batteries that can only be replaced by qualified technicians or after-sales service.
- The lithium-ion battery pack contains substances that are hazardous to the environment. Before disposing of the appliance, please first remove the battery pack, then discard, or recycle it in accordance with local laws and regulations of the country or region it is used in.
- The appliance must be disconnected from the power supply when removing the battery. Keep batteries out of the reach of children. Never put batteries in mouth. If swallowed, contact your physician or local poison control.
- Under abusive conditions, never contact the battery from which the liquid may be ejected. If contact accidentally occurs, rinse with water. If liquid contacts eyes, seek medical help immediately. Liquid ejected from the battery may cause irritation or burns.
Important Safety Instructions
Symbols
Class Il equipment
Time-lag miniature fuse-link where T 3.15A is the symbol for the Le
time/current characteristic
Detachable supply unit
Read operator’s manual
Motorized cleaning head for water suction cleaning
WEEE Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a ZACE designated collection point for
the recycling of waste electrical and electronic Z ° Axa equipment, appointed
by the government or local authorities. Correct So disposal and recycling will
help prevent potential negative consequences S&S to the environment and human
health. Please contact the installer or local authorities for more information
about the location as well as terms and conditions of such collection points.
SAVE THESE INSTRUCTIONS
For Household Use Only
We, Dreame Trading (Tianjin) Co., Ltd., hereby declares that this equipment is
in q | A compliance with the applicable Directives, European Norms, and
amendments. The full SX QD text of the EU declaration of conformity is
available at the following internet address:
https://global.dreametech.com
For detailed e-manual, please go to
https://global.dreametech.com/pages/user-manuals-and-fags
Product Overview
Packing List
Wet and Dry Vacuum Floor Washer
- Self-Cleaning Button
- Mode Switch
- Power Switch
- Handvac Release Button
- Display Screen
- Handvac Mode Switch
- Handvac Power Switch
- Used Water Tank Release Button
- Used Water Tank Handle
- Used Water Tank
- Brush Roller Cover Release Buttons
- Brush Roller Cover
- Brush Roller Handle
- Brush Roller Release Button
- Clean Water Tank
- Clean Water Tank Handle
- Clean Water Tank Release Button
- Voice Prompt Button
• Press briefly to activate the voice prompt or adjust the volume Press and hold for 3 seconds to access the language settings.
Press to switch between languages.
Press and hold to confirm the selection
Charging Base
Display Screen
Auto Mode
Suction Mode
Auto Mode
Self-Cleaning
Press briefly to enable this function (battery level z 15%) Press and hold
self-cleaning button for 3 seconds to activate drying mode.
Standard Mode (Handvac)
Turbo Mode (Handvac)
Charging Indicator
• Orange (charging): Battery level <20%
• Green (charging): Battery level z 20%
Low Battery Indicator
• Orange: Battery level <20%
• Green: Battery level z 20%
Error Messages
Insufficient water in the Clean Water Tank
Used Water Tank full/ Used Water Tank not installed
Blocked tube
Brush roller stuck
Note: If the appliance is not working properly, the screen display will
show an error message. Please refer to the troubleshooting table to find your
solution.
Installation
Installing the Handle
Insert the end of the handle vertically into the port on the top of the
appliance as indicated until you hear a click.
Note: To disassemble, extend a hard object into the hole on
the back of the appliance to press contacts and pull the handle upwards at the
same time.
Installing the Storage Box
Install the storage box onto the charging base.
Installing the Accessory Storage Mount
Insert the support rod vertically into the storage mount until you hear a
click.
Note: To remove the support rod, extend a tool into the hole on the bottom
of the mount to press contacts and pull the rod upwards at the same time.
Charging
- Place the charging base against a wall on level ground and connect it to a power source. Fully charge the appliance before first use.
- Place the appliance on the charging base, the on the screen will light up to indicate the charging status. When charging, the number on the display screen represents the current battery level as a percentage. When the number reaches 100, the battery is fully charged and the will turn off.
Note: If no operation is performed within 10 minutes, the appliance will enter the sleep mode. To extend the battery life time, the battery keeps cooling down for about one hour automatically after you have used the appliance for a long time.
How to Use
Switching Modes
The appliance is powered on in Auto mode by default, you can switch to
Suction mode as needed.
Auto Mode
While washing the floor, the appliance can adjust its suction power according
to different situations.
Suction Mode
If Suction mode is selected, the appliance will vacuum water only and the
brush roller will not be dampened. No water is coming out of the Clean Water
Tank.
Standard Mode (Handvac)
When the appliance converts to a handheld vacuum, it is powered on by default
in Standard mode.
Turbo Mode (Handvac)
Press the Handvac mode switch to select the Turbo mode.
Using as a Floor Washer
-
Fill the Clean Water Tank: Press the Clean Water Tank release button to remove the tank. Open the tank cover and fill the tank with clean water. Re-install the Clean Water Tank and ensure it clicks into place.
Note:
For better cleaning performance, it is recommended to add 10ml detergent with the bottle cap into the full Clean Water Tank, then shake gently and evenly for use.
For removing stubborn stains, it is recommended to fill the Clean Water Tank with warm water, and the temperature of water is below 45°C /113 °F .
Do not add any liquids other than the officially-approved cleaner. -
Start cleaning: Gently step on the brush cover and recline the appliance backwards.
Press the power switch to start operating, press the mode switch to switch between the Auto mode and the Suction mode according to your needs.
Note:
Do not vacuum any foamy liquids.
If the appliance is in the upright position while working, the current task will be suspended.
The appliance is suitable for cleaning floors, marble, tiles and other hard surfaces.
Do not recline the appliance backwards more than 140° to prevent the appliance from leaking water.
When the appliance is in operation, do not lift it off the ground, move it, tilt it or lay it flat. Doing so may cause the used water to flow into the motor. -
Empty the Used Water Tank: Press the Used Water Tank release button to take out the tank. Remove the tank cover and pour out the used water. Close the tank cover and re- install the tank before use.
Self-cleaning Mode
- Place the appliance back onto the base while you finish cleaning.
- Briefly press the self-cleaning button on the top of the handle to start/stop self- cleaning.
- Empty the Used Water Tank while self-cleaning is completed. Then the appliance starts drying mode. Press the button to exit drying mode.
Note: The setf-cleaning mode can be enabled only when the appliance is being charged and the battery level is more than 15%.
Drying Mode
- Press and hold the self-cleaning button for 3 seconds to activate drying mode.
- The appliance will be charged once drying is completed.
Note:
- Clean the charging base if there are any stains left on the base after self-cleaning is complete.
- If cleaning the brush roller manually, please air dry thoroughly or dry it by using drying mode several times.
Using as a Handheld Vacuum
- Press the Handvac release button to remove the Handvac.
- Install the dust cup assembly and other attachments as shown in the diagram until you hear a click.
- Briefly press the Handvac power switch to start operating. Briefly press the Handvac mode switch to switch between Standard mode and Turbo mode according to your needs.
Note: Motorized mini-brush should not be used with the extension rod.
Using Different Attachments
Combination Tool: For cleaning corners, stairs, sofas, coffee tables and other
narrow spaces.
Soft Roller Brush: Suitable for cleaning hard floors such as marble and floors.
Motorized Mini-Brush: For vacuuming dirt, pet hair, and other stubborn debris from sofas, bedding, and other fabric surfaces.
Accessory Storage Mount: Store the dust cup assembly, soft roller brush, combination tool, and motorized mini- brush on the mount as shown in the diagram.
CAUTION! DO NOT store the handheld vacuum on the accessory storage mount
to avoid damage.
Storage Box: Store the cleaning brush, the filter, and the brush roller
on the storage box as shown in the diagram.
Care and Maintenance
Tips:
- Turn off the appliance before performing care and/or maintenance. Do not touch the Power Switch.
- Replace parts if needed. The parts must be replaced by those available from the manufacturer or its service agent.
- If the appliance is not used for an extended period, fully charge it, unplug the power adapter, and store the appliance in a cool, low-humidity environment away from direct sunlight. To avoid over-discharge of the battery, charge the appliance at least once every 3 months.
Cleaning the Used Water Tank and the Filter
- Press the Used Water Tank release button and take out the Used Water Tank.
- Take out the filter from the Used Water Tank cover. Remove the tank cover and pour out the wastewater.
- Rinse the Used Water Tank and the tank cover with water, the provided cleaning brush can be used to clean the inner wall of the tank.
- Close the Used Water Tank cover, re-install the Used Water Tank and ensure the tank clicks into place.
Note:
- Cleaning the Used Water Tank after each use is recommended.
- Replacing the filter every 3 to 6 months is recommended.
- When the filter is dirty and needs washing, rinse it with water. It must be completely dry before use.
Cleaning the Tube and the Dirt Sensor
Remove the Used Water Tank, wipe the tube and the dirt sensor with a wet cloth
before use.
Cleaning the Dust Cup Assembly
- Press the dust cup release button and remove the cup.
- Take out the filter and the cyclone assembly from the dust cup, then empty the cup.
Note: To reduce the risk of electric shock or injury, do not rinse the cyclone assembly with water. - Tap the filter gently or clean it with the cleaning brush. Rinse the filter and the dust cup with water.
- Dry the filter and the dust cup completely before use.
Note:
- Cleaning the dust cup after each use or after the amount of dust in the cup reaches the MAX line is recommended.
- Replacing the filter every 3 to 6 months is recommended.
Cleaning the Brush Assembly
- First, press the brush roller cover release buttons inwards on both sides to remove the brush roller cover. Next, press the brush roller release button and the handle of the brush roller will pop out. Pull the handle to take out the brush roller.
- Clean out any hair and debris tangled on the brush roller with the provided cleaning brush. Rinse the brush roller with clean water and dry it completely.
- Wipe the suction inlet with a dry cloth or wet tissue. Do not rinse the brush assembly with water.
- After cleaning the brush roller, re-install the brush roller and the brush roller cover. You will hear a click to indicate that they are installed in place.
Note:
- Clean as needed. Alternating use of the two provided brush rollers is recommended.
- Replacing the brush roller every 3 to 6 months is recommended.
Cleaning the Soft Roller Brush
- As shown in the picture, press the brush roller release button to remove the roller from the slot.
- When it is dirty, rinse the brush roller with clean water. Stand the brush roller upright until it is fully dry.
Cleaning the Motorized Mini-Brush
- Use a coin as illustrated to rotate the lock counterclockwise, and remove the brush roller until you hear a click.
- When it is dirty, rinse the brush roller with clean water. Stand the brush roller upright until it is fully dry.
Troubleshooting
If an error occurs, the appliance will stop working. Please refer to the following table for troubleshooting. If the problem persists, please contact the customer service.
Error| Possible Cause|
Solution
---|---|---
The appliance does not work.| The appliance is out of battery or its battery
level is low.| Fully charge its battery before use.
The appliance is in the upright position.| Recline the appliance backwards.
The appliance is overheating due to blockage and the high-temperature cut-off
has activated.| Clear the blockage and wait until the temperature returns
normal.
The Used Water Tank is full.| Empty the Used Water Tank.
The handle or Used Water Tank is not installed in place.| Ensure the handle or
Used Water Tank are all properly in place.
The appliance charges slowly.| The temperature of the battery is too low or
too high.| Wait until the battery’s temperature returns normal.
The suction power of the appliance is weak.| The filter is clogged.| Clean the
Used Water Tank and the filter that is in the dust cup.
There are some foreign objects in the tube and the suction inlet or the tube
and the suction inlet are blocked.| Clean the tube and the suction inlet.
The motor is making a strange noise.| There is too much dirty water in the
Used Water Tank.| Empty the Used Water Tank.
The suction inlet is blocked.| Clear any blockage in the suction inlet.
The display screen does not light up while charging.| The charging base plug
is not inserted into the electrical outlet properly.
plug is inserted in place.| Make sure the charging base
The appliance is not placed onto the charging base properly.| Make sure the
appliance is placed onto the charging base properly.
No water is coming out of the ppli .| The Clean Water Tank is not properly
installed in place, or the water in the Clean Water Tank is insufficient.| Re-
install or fill the Clean Water Tank.
It takes 30 seconds to dampen the brush roller.| Turn on the appliance and
check again in 30 seconds.
The vent leaks water.| A collision or a sharp pull causes water to enter the
motor.| Move the appliance gently back and forth while it is turned on.
The filter is not completely dry after being cleaned.| Dry the filter
completely before use.
Self-cleaning fails.| The brush roller may be jammed by large debris.| Open
the brush roller cover to check and clean the brush roller.
The appliance is not being charged.| Make sure the appliance is being charged
before enabling the self-cleaning function.
Self-cleaning cannot be enabled if the battery level is lower than 15%.| The
self-cleaning function can only be enabled when the appliance is being charged
andthe battery level is more than 15%.
The Used Water Tank is not installed in place, or the Used Water Tank is
full.| Re-install or empty the Used Water Tank.
The Clean Water Tank is not installed in place, or the water in the Clean
Water Tank is insufficient.| Fill or re-install the Clean Water Tank.
Poor drying performance.| The air outlet and air inlet of the charging base
may be blocked.| Check and clear the blockage of air outlet and air inlet.
For additional services, please contact us via aftersales@dreame.tech Website: https://global.dreametech.com
Error Prompts and Solutions
If the appliance is not working properly, the screen display will show an error message. Please refer to the troubleshooting table to find your solution.
Error Icon| Possible Cause|
Solution
---|---|---
| Insufficient water in Clean Water Tank| Fill the Clean Water Tank.
| Used Water Tank not installed| Install the Used Water Tank.
Used Water Tank full| Empty the Used Water Tank.
| Brush roller stuck| Clean the brush roller with the provided cleaning brush.
| tube| Check whether the filter is clogged. Alternatively, clean the tube and
the dirt sensor.
Error Code| Possible Cause|
Solution
---|---|---
El -E7| Error| Restart the appliance for troubleshooting. If the problem
persists, please contact customer service.
Hl-H6
H7| Battery overheating| Wait until the battery’s temperature returns normal.
Specifications
Wet and Dry Vacuum Floor Washer
Model| HHV4| Rated Power| 300 W
Rated Voltage| 21.6 V =| Charging Voltage| 27 V
Used Water Tank Capacity| 700 mL| Clean Water Tank Capacity| 900 mL
Charging Time| Approx. 4.5 hours| Drying Time| Approx. 30 mins
Charging Base
Model| HCB3| Rated Power| 150 W
Input| 220-240 V— 50/60 Hz| Output| 27 V = 1.6 A
Model| 11036| Rated Power| 230 W
Input| 220-240 V-N.- 50/60 Hz| Output| 27 V = 1.6 A
Motorized Cleaning Head
Model| HCR14B
Rated Power| 50 W| Rated Voltage| 21.6 V
The rated power is measured during a representative period when the appliance works at full power at the beginning, with the charging and drying functions turned on simultaneousl
Battery Disposal and Removal
The built-in lithium-ion battery contains substances that are hazardous to the
environment. Before disposing of the battery, make sure the battery is removed
by qualified technicians and discarded at an appropriate recycling facility.
– the battery must be removed from the appliance before it is scrapped;
– the appliance must be disconnected from the supply mains when removing the
battery;
– the battery is to be disposed of safely.
Removal Guide
- Remove the display screen by rotating it with a tool.
- Remove the screws on the battery cover in turn and then pry open the cover with proper tools.
- Unplug the terminals between the battery and PCB board to remove the battery.
CAUTION:
- Before removing the battery, disconnect the power and run out the battery as much as possible.
- Unneeded batteries should be discarded at an appropriate recycling facility.
- Do not expose to high temperature environment to avoid risks of explosion.
- Under abusive conditions, liquid may be ejected from the battery. If contact occurs, flush with water and seek medical help.
- The word “dreame” is the abbreviation of Dreame Technology Co., Ltd. and its subsidiaries in China. It is the transliteration of the company’s Chinese name ” JB ° which means striving for excellence in every endeavor and reflects the company’s vision of continuous pursuit, exploration and search in technology.
Website:https://global.dreametech.com
Manufactured by: Dreame Trading (Tianjin) Co., Ltd.
Made in China
Documents / Resources
|
DREAME H12 Dual Wet and Dry
Vacuum
[pdf] User Manual
W2221-H12DUAL, H12, H12 Dual Wet and Dry Vacuum, Dual Wet and Dry Vacuum, Wet
and Dry Vacuum, Dry Vacuum, Vacuum
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>