VEVOR AX-EJD Solar Barn Light User Manual

June 17, 2024
VEVOR

VEVOR AX-EJD Solar Barn Light User Manual
VEVOR AX-EJD Solar Barn Light

We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only representsanestimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if youareactually saving half in comparison with the top major brands

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel freetocontact us:
CustomerService@vevor.com

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear inter predation four user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t in form you again if there are any technology or software updates on our product.

Reading IconWarning- To reduce the risk of injury, user must read instructions manual carefully.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may casein desired operation.
Unable to charge in the shadow
Do not install in a location without direct sunlight, if the photovoltaic panel cannot receive sunlight, the solar lamp will not work properly at night.
Installed in direct sunlight

HOW TO INSTALL?

  1. Cover the solar panel or place the light in a dark environment, turn on the switch to check if the light work normally.

  2. As shown in the figure, justify groove part to fix the connector.

  3. Thread the bracket through the mounting base

  4. Fix the bracket and base together with nuts.

  5. Use long screws to fix the base at the position you need to install, unplug the blue cover, and connect the light head with the bracket

  6. Fix the light head and the bracket firmly with screws.

LIGHTING MODES

Select mode by pressing the white button.
Pressing button

Pressing button
Press white button to turn on the switch, and the first mode is auto dusk to dawn, the light will keep dim light all night, regardless of whether motion is detected by the sensing range of the light.

Pressing button
When motion is detected nearby, the light will display 60% brightness, if no motion is detected within 20s, it will display 30% brightness.

Pressing button
At night the lamp will remain OFF until the sensor detects nearby movement then turn to 100% brightness, light will turn OFF after no motion is detected within 20 seconds.

NOTE : When using it for the first time, if the wall lantern does not light up, please place the wall lantern in direct sunlight to charge it for 8 hours.

FREQUENTLY ASKED QUESTIONS

Why does my light not come on at night?

(1) Make sure the switch is ON (White button). Light can only be charged when the switch is turned on. (2) Make sure that the location you install does not have shade or eaves to block the sun. (3) Make sure that there are no other light sources above the solar panel at night, such as street lights.

Does the solar panel require the direct sun to charge?

The solar panel must be installed in a location where it can receive full direct sunshine (when available) and usually set the solar panel facing South at an appropriate angle. The solar panel must not be installed in a shaded or part-shaded location.

What type of battery does my solar hanging light require to operate?

The solar barn light requires one Lithium-ion 3.7V 1500 mash battery, battery model: 18650.

Can I use any regular bulb for the solar barn light?

Only bulbs purchased through Aulani to can be used for this product.

IF THE LIGHT DOES NOT TURN ON AT DUSK AFTER 6-8 HOURS OF CHARGING:

  1. Unscrew the three fixing screws as shown in the picture.
    Screws shown picture

  2. Uncover the lampshade gently upward.
    Screws shown picture

  3. Check whether the internal circuit is off, loose, etc.
    Screws shown picture

LIST OF ACCESSORIES

  1. Products*1
  2. Instructions*1
  3. Plastic Expansion (4.5mm35mm)2
  4. Galvanized Screws (4.5mm30mm)2
  5. Irons*1
  6. Install the Round Iron Disc *1
  7. Ironed Fixing Nut *1
  8. The Lamp Body Fixes the Plastic Parts *1
  9. The Lamp Body Fixing Rubber Part Screw(412mm) 1
  10. Dense Bags *1

Technical Support and E-Warranty Certificate www.vevor.com/support
Company logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals