G rbach Y23070915 Stainless Steel Shower Column Without Mixer Instruction Manual
- June 17, 2024
- G RBACH
Table of Contents
G rbach Y23070915 Stainless Steel Shower Column Without Mixer
Technical Specifications
- Pressure: recommended 3-12 bar, if more than 12 bar please install
Product Information
This product is a sliding hand shower holder designed for use in shower columns. It allows for flexible adjustment of the distance between wall holders up to a maximum of 84cm. The sliding mechanism is operated by pressing a grey button to adjust the height of the hand shower holder. The product is manufactured by Zhangpu Juhe Sanitary co., Ltd.
Installation Instructions
- Fix the shower column to the wall holder.
- Press the grey button while installing the sliding hand shower holder into the shower column. Ensure the grey button faces upward.
- Adjust the distance between wall holders as needed within the range of 60-80cm.
- Ensure that the 24mm diameter hole of the sliding hand shower holder faces upwards and the 20mm diameter hole faces downwards.
- Tighten the nuts of the shower hose by hand to avoid surface damage.
- Check all connections for leaks after installation.
- For safety, have installation carried out by competent persons and turn off the general water supply before installation.
Safety Instructions
- Please only have the installation carried out by competent persons.
- Turn off the general water supply before installation.
- Make sure all seals are seated correctly.
Troubleshooting
- If the shower head has water dropping, ensure it is kept horizontally.
- If water comes out from the hand shower only when turning down the handle of diverter, reinstall the shower hose correctly.
- If nozzles are clogged, use a cloth and clear water to wipe them and remove scale.
FAQ
Q: What should I do if water is leaking from connections after
installation?
A: Check all connections for leaks and tighten them if necessary.
Improper installation is not covered by warranty.
Q: How do I adjust the height of the hand shower holder?
A: Press the grey button while sliding the hand shower holder along the
shower column to reach the desired position. Ensure the grey button faces
upward to prevent sliding down along the column.
Instructions for use:
Notice! All pictures shown are for illustrative purposes only.
Deviations from the products are possible.
The data may change with different installation scenarios.
Please install according to the actual situation.
Parts List
TOOLS
INSTRUCTION
-
The distance between two wall holders can be adjusted flexibly up to a maximum of 84cm.
-
Press the grey button while installing the sliding hand shower holder into the shower column.
Attention! -
While installing and adjusting the height of hand shower holder, please always press the grey button on the sliding hand shower holder until it reaches the desired position, to avoid the damage of spring.
Please make sure the grey button on the sliding hand shower holder must face upward. If it facing down, the hand shower holder will slide down along the shower column. -
The 24mm diameter hole of sliding hand shower holder facing upwards, and 20mm diameter hole facing downwards.
Attention!
Please tighten the nut at the bottom of the shower column by hand, or cover
the nut with a cloth before you tighten it by pliers or wrench, to avoid the
damage of surface.
Attention!
Please tighten the nuts of shower hose by hand, or cover the nut with a cloth
before you tighten it by pliers or wrench, to avoid the damage of surface.
Troubleshooting
- Shower head with water dropping: Please always keep the shower head to be horizontally.
- When turn down the handle of diverter, water comes out from hand shower,but turn the handle up, water does not run out from shower head: The shower hose was installed to incorrect connector of diverter, please reinstall the shower hose correctly.
- Nozzles clogged and water does not come out: Please use a cloth and clear water to Please tighten the nut at the bottom of the wipe the nozzles and remove scale.
Attention!
Check all connections leaking or not after installation. The improper
installation of products is not covered by warranty. Especially the
consequential damage caused by improper installation is not guaranteed.
Warranty conditions
We guarantee the perfect functioning of our items for two years. In the event
of a warranty claim, please contact the trading partner from whom you
purchased the item first. If in doubt, they will contact us.
Please tell us as precisely as possible what damage/error / defect the item
has.
- The guarantee begins on the date of purchase of the item.
- Please keep the invoice. The invoice serves as proof of guarantee.
- The subject of the guarantee is the defect-free function of the item.
Defects must be reported immediately after they occur within the stated period of the guarantee. The defective article must be kept and returned to the trading partner within 30 days.
The following cases are excluded:
- Normal wear and tear.
- Improper installation.
- Improper handling.
- Improper repair.
Please read the instructions completely before installation and follow the
instructions. These instructions contain important information on
installation, adjustment, maintenance and spare parts.
Keep the instructions in a safe place, and pass them on to subsequent owners.
The guarantee is granted by Dylin GmbH, Glinde, 21509, Germany.
Safety instructions
- Please only have the installation carried out by competent persons.
- Please turn off the general water supply before installation.
- Make sure that all seals are seated correctly.
Disposal
To protect against transport damage, your product is delivered by a solid
packaging.
The packaging is made from recyclable materials. Dispose of them in an
environmentally friendly manner.
Don’ t throw the product into the normal household waste at the end of its
service life, but inquire with your local government about the options for
environmentally friendly disposal.
Technical specifications
- Pressure: recommended 3-12 bar, if more than 12 bar please install pressure reducer.
- Water temperature: Max. 80°C.
Service-Address
Importer: Dylin Gmbh
Address: Humboldtstr. 25A, 21509 Glinde, Germany.
© 2018 Dylin Gmbh. All rights reserved.
Manufacturer: Zhangpu Juhe Sanitary co., Ltd.
Area A, No.211 Maipu, Maipu Village, Sui’an Town, Zhangpu County, Zhangzhou
City, Fujian Province,China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>