SEALEY SPB37W Broadcast Spreader 37kg Walk Behind Instruction Manual
- June 17, 2024
- SEALEY
Table of Contents
BROADCAST SPREADER 37KG
WALK BEHIND
MODEL No: SPB37W
SPB37W Broadcast Spreader 37kg Walk Behind
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction manual
SAFETY
Before each use, check that there is no damage to the spreader and that all
fixings are tight.
Replace or repair damaged parts . Use only recommended parts.
Unauthorised parts may be dangerous and will invalidate the warranty.
Ensure that the operator is fully trained and competent to operate the
spreader.
Ensure that all chemical safety instructions are adhered to when
handling products for use in the spreader . A full range of personal safety
equipment is available from your Sealey dealer.
Always distribute the load evenly.
Ensure all non essential personnel keep a safe distance when the spreader
is in use.
** Keep hands and feet away from moving parts.
X DO NOT overload the spreader – see Specification.
X DO NOT leave unattended, especially when loaded.
X DO NOT allow anybody to sit, stand, or ride on the spreader.
X DO NOT allow untrained personnel to use the spreader.
X DO NOT allow children to play in or climb onto the spreader.
X DO NOT use on windy days when spreading seeds or herbicides.
X DO NOT tow this spreader with a motorized vehicle of any sort.
X DO NOT use the spreader for purposes other than for which it is
designed.
X DO NOT operate the spreader when you are tired or under the influence
of alcohol, drugs or intoxicating medicines.
** When loaded, DO NOT operate the spreader over edges, rough surfaces etc
. where the spreader is at risk of overturning.
WARNING! Failure to comply with these instructions may result in damage
to spreader or other property and/or personal injury.
SPECIFICATION
Model No. ………………………………. SPB37W
Capacity (Volume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .29L
Capacity (Volume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .37kg
Dimensions (W x D x H) . . . . . . . . . . . . . . . . . . .535 x 940 x 820mm
Spread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .3-3 .6M
INTRODUCTION
Manufactured with a strong tubular steel frame and polypropylene dispensing
hopper. Fitted with nylon gear, rain cover, pneumatic tyres and adjustable
feed system. Includes hopper screen to ease spreader flow and filter out
unwanted contaminants. Sprays in 360° motion to cover a large area. Suitable
for a variety of horticultural agents including grit, seed, salt, fertilizer
and weedkiller.
ASSEMBLY
Note! Before assembly ensure
there are no missing parts or fixtures .
4.1 Refer to fig .1.
4 .1 .1 Slide the Impeller (14) over the vertical axle on the gearbox (12)
4 .1 .2 Secure the Impeller to the axle with a round head bolt M4x20 (4)
Ensure the impeller is secured to the lower hole on the axle .
4.2 Refer to fig .2.
4 .2 .1 Slide the wheel frames (15) over the axle, ensure the bush housing is
facing inwards.
4 .2 .2 Secure with support rod (19) and M6x40 hex bolts (2).
4.3 Refer to fig .3.
4 .3 .1 Take the hopper (13) and lay it upside down, lower the gearbox and
frame onto the hopper, inserting the vertical axle through the hopper.
4 .3 .2 On top of the wheel frame lay the support leg (16), secure together
with hex bolts M6x70 (1) with large washer (6), Inserting from inside the
hopper securing with lock nuts (7) on the outside.
4.4 Refer to fig .4.
4 .4 .1 Slide the inner axle bushes (11) over the axle and push into the
frame. Ensure a tight fit.
4 .4 .2 Put on the wheels (18) . Secure the right hand wheel using hex bolt
M5x45 (3) and a lock nut (8).
4 .4 .3 After the wheel place a flat washer (5) over the end of the axle and
then the axle caps (9). Use a soft faced mallet to ensure the axle is seated
correctly.
4.5 Refer to fig .5.
4 .5 .1 Turn the spreader onto its wheels and slide the handle assembly (17)
around the frame, secure with 4 M6x40 hex bolts (2) and lock nuts (7).
OPERATION
5.1 The spreader is designed to be pushed at three miles an hour, which is a
brisk walking pace . Slower or faster speeds will change the spread pattern .
Wet fertiliser will also change the spread pattern.
5.2 Use the Stop bolt on the gauge to ensure the same amount of distribution.
5.3 See figs .7 & 8 for suggested walking patterns depending on the level of
coverage you require.
5.4 Always start walking prior to opening the flow control plate.
5.5 Every time you are ready to stop, or turn to make a new pass, close the
flow control plate to stop dispensing the material and continue one more
stride . This reduces waste and avoids damaging a lawn with over saturated
product coverage.
5.6 To ensure consistent coverage, make sure each broadcast pattern slightly
overlaps the previous one.
5.7 Make sure that any broadcast material does not come into contact with
trees, shrubs and flowers that could be harmed by the material.
5.8 Clean the spreader thoroughly after each use paying particular attention
to the shut off plate and the bottom of the hopper.
(CHART ‘A’) SQUARE FOOT COVERAGE
PER BAG (LBS/1000SQ.FT)
WEIGHT OF BAG (LBS)| 5000 SQ.FT COVERAGE| 10000 SQ.FT COVERAGE| 15000 SQ.FT
COVERAGE
---|---|---|---
5| 1.0Ib| 0.51b| 0.3Ib
10| 2.0Ib| 1.0Ib| 0.71b
15| 3.0Ib| 1.51b| 1.0Ib
20| 4.0Ib| 2.0Ib| 1.31b
25| 5.0Ib| 2.5Ib| 1.7Ib
30| 6.0Ib| 3.0Ib| 2.0Ib
35| 7.0Ib| 3.5Ib| 2.31b
40| 8.0Ib| 4.0Ib| 2.31b
45| 9.0Ib| 4.5Ib| 3.0Ib
50| 10.0Ib| 5.0Ib| 3.31b
55| 11.01b| 5.5Ib| 3.71b
(CHART ‘B’) SPREADER SETTINGS/SPREADER WIDTHS
MATERIALS TO BE
USED| LBS/1000 SQ.FT| G/M2| SPREADER
SETTING| SMALL PARTICLE
SPREAD| MEDIUM PARTICLE
SPREAD| LARGE PARTICLE
SPREAD
---|---|---|---|---|---|---
GRIT
SEED
FERTILISER
WEED
KILLER
E.T.C.| 1| 5| 5| 5-6 ft| 6-9 ft| 9-12 ft
2| 10| 8| 5-6 ft| 6-9 ft| 9-12 ft
3| 15| 10| 5-6 ft| 6-9 ft| 9-12 ft
4| 20| 13| 5-6 ft| 6-9 ft| 9-12 ft
5| 25| 15| 5-6 ft| 6-9 ft| 9-12 ft
6| 30| 18| 5-6 ft| 6-9 ft| 9-12 ft
7| 35| 20| 5-6 ft| 6-9 ft| 9-12 ft
8| 40| 23| 5-6 ft| 6-9 ft| 9-12 ft
9| 45| 25| 5-6 ft| 6-9 ft| 9-12 ft
10| 50| 28| 5-6 ft| 6-9 ft| 9-12 ft
11| 55| 30| 5-6 ft| 6-9 ft| 9-12 ft
5.9 CALCULATING THE AMOUNT OF MATERIAL NEEDED.
(refer to Charts ‘A’ & ‘B’)
To calculate the amount of material needed e .g lawn fertiliser, divide the
coverage stated on the packaging by the weight of the fertiliser bag . For
example, a 10lb bag of fertiliser with a coverage of 10,0000 sq . ft . will
distribute 1lb of fertiliser every 1,000 sq .ft . at full rate or 1/2lb . of
fertiliser every 1,000 sq . ft . at half rate .
5.10 For pre-calculated rates see Chart ‘A’ (Example: A 25lb bag with a 15,000
sq . ft . coverage requires 1 .7lb of fertiliser per 1,000 sq .ft .
5.11 Use Chart ‘B’ to find the closest spreader setting . For example, 1 .7lb
per 1000 sq .ft . = spreader setting 8)
MAINTENANCE
6.1 After each use clean material out of hopper.
6 .1 .1 Rinse/dry inside and outside of spreader after each use.
6 .1 .2 Before operating make sure that the tyres are inflated to the correct
pressure i .e . 30psi .
6 .1 .3 Periodically check all fastenings are tight.
6 .1 .4 Annually clean and lightly lubricate parts.
6 .1 .5 Touch up all scratched or worn painted metal surfaces.
6 .1 .6 To avoid damaging the spreader never exceed the rated load capacity of
37kg.
6.2 STORAGE.
6 .2 .1 Before storing ensure that the spreader is clean and dry.
6 .2 .2 Store indoors or in a protected area during severe weather and in the
winter months.
6 .2 .3 Never allow material to stay in the hopper for extended periods of
time.
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
REGISTER YOUR PURCHASE HERE**
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk
Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
****www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>