PETSITE Pet Dog Running Machine for Small and Medium Sized Dogs User Manual

PETSITE Pet Dog Running Machine for Small and Medium Sized Dogs

Introduction

WARNING: Connect the treadmill to a properly grounded outlet only.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance to electric current reducing the risk of electric shock. This treadmill is equipped with a cord having an equipment grounding connector and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded by all local codes and ordinances.
DANGER: Improper connection of the treadmill grounding connector can result in the risk of electric shock. Check with a qualified electrician, if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the treadmill. If it will not fit your outlet, have a properly grounded outlet installed by a qualified electrician.

• Keep hands clear of all moving parts. Never place hands, or feet under the treadmill.
• Do not use the treadmill on a carpet.
• Before each use, check that the running belt is aligned and centred on the treadmill deck and all visible fasteners on the treadmill are sufficiently tightened and secure.

PRODUCT PARTS

MAIN PARTS OF NAME

ASSEMBLY INSTRUCTIONS

Warning: Do not connect the Treadmill to a power source before completing assembly.
Open the carton, remove the mainframe and the components and place it on the floor in an open area.

1. Assemble U-tube using the pre-installed screws as Fig 1
2. Assemble L-tube using the pre-installed screws as Fig 2 and Fig 3
3. Adjust the Velcro fastener on the tube to the proper place, then stick the Protection pads as shown in the picture.
4. Assemble the Panel using the pre-installed screws as Fig 4
5. Plug-in wiring as Fig 5
6. Assemble Wheels using the pre-installed knob as shown in the picture.
7. Place the Safety key on the panel and put the Remote control as shown in the picture.

PANEL OPERATION INSTRUCTION

1. Plug the power, then place the safety key on the computer and turn on the power switch which is located at the front of the treadmill.
2. The window will display “0.0”. Then press the “START/STOP” key to start the treadmill, after the 5-second countdown, the treadmill will start at the speed of 0.5MPH.
3. You may press the speed“+” or speed“-” key to increase or decrease the running speed during exercise. Each increment or reduction will be of 0.1 MPH. The speed range is from 0.5 MPH to 7.5 MPH.
4. You may also use the Quick Speed keys (2/3/4/5) on the console to directly access a preset speed.
5. Press the “START/STOP ” key to stop the treadmill. For emergency stops, remove the Safety Key. The Running Belt will stop automatically and all windows will display “E07”.

Note
The default duration of the operation is 30 minutes. The operation will automatically be turned off when time is up, you can press the start button to operate the device again.

REMOTE CONTROL OPERATION

1. Plug the power, then place the safety key on the computer and turn on the power switch which is located at the front of the treadmill, the window will display “0.0”.
2. After installing the battery, press the “ ” on the remote control near the treadmill to start the treadmill, after a 5-second countdown, the treadmill will start at the speed of 0.5MPH.
3. You may press the speed “+” or speed “-” key to increase or decrease the running speed during exercise. Each increment or reduction will be of 0.1 MPH. The speed range is from 0.5 MPH to 7.5 MPH.

Remote Control: Place the AAA battery in the remote control.

NOTE 1: The treadmill will make a “BI” sound under any valid press.
NOTE 2: The battery is not pre-installed.

DISPALY WINDOW AND KEY

1. LCD window: SPEED, TIME, DISTANCE, CALORIE, PROGRAM.
2. Functional keys: SPEED+, SPEED-, START / STOP, MODE, PROGRAM.
3. Quick keys for speed selection: 2,3,4,5.
4. When the display window shows “E07”, place the Safety key on the computer to activate operations.

MODE KEY

1. Press the “MODE” key to access countdown Mode. You may set a target Time, Distance, or Calories burned by using the speed “+” or “-” key to adjust to the desired amount. Press the “START/STOP” key to start your set workout.
2. Press the “START/STOP” key to stop the treadmill.
3. The system will shut down and stop after your desired goal has been reached and the machine will stop.

PROGRAM(PROG.) KEY

1. Before starting the treadmill, press the “PROG.” button to select the program, you may select P1, P2, P3, P4, P5, P6, P7, P8, P9, P10, P11, P12.
2. The TIME window will display a flashing preset time of 30:00 minutes, press the “+” or “-” to increase or decrease the desired workout time. The TIME range is from 8:00 to 99:00 minutes.
3. Press the “START” button to start the treadmill and Press the “STOP” button to stop the treadmill.
4. Under program mode, the preset workout time is 30 minutes, 1/20 minutes per interval.

Note: The “MODE” key and “PROGRAM” key must be selected before starting.

DAILY MAINTENANCE

WARNING
Turn off and unplug the treadmill before proceeding with any maintenance or visual inspections. Failure to do so may result in serious injury.
AT THE END OF EVERY EXERCISE SESSION ALWAYS

1. Use the Power Switch to turn the treadmill off.
2. Always position and store the Power Cord where it is clear from all pathways.
3. Unplug the Power Cord from the electrical outlet. This is especially important if you are not going to use your treadmill for extended periods.
4. Wipe all treadmill surfaces with a dry cloth or towel especially perspiration on the handlebars, console, running belt or other treadmill components.
5. Check and tighten screws at the fixing point.
6. Do not hang clothes or other objects on the machine.

STORAGE
Store your treadmill in a clean and dry environment. Ensure that the Power Switch is off and is unplugged from the electrical outlet.

MOVING
The treadmill has been designed and equipped with wheels (11) for easy mobility. Before moving, ensure that the Power Switch is in the “OFF” position and the power cord is unplugged from the electrical outlet. Tilt the base frame of the treadmill and then roll the treadmill to the desired position.

LUBRICATION YOUR TREADMILL

The treadmills have already been spread with “Silicone Oil” in advance before leaving the manufacturing plant. Silicone oil is without volatility and has gradually permeated through the running belt. There will be no need to re- spread the oil in normal circumstances.
To maintain the running belt, we have included a small bottle of “Silicone Oil “. The “Silicone Oil” may be re-spread once the resistance has been increased and the running belt starts rubbing against the running deck. To hold open the centre of the running deck. Allow the silicone oil to “set” for one minute before using the treadmill.

NOTE: Only use the “Silicone Oil” lubricants for this equipment. In addition, do not add any other oil ingredients; otherwise, the treadmill will be damaged. Do not over-lubricate the walking board. Excess lubricant should be wiped off with a clean towel.

RUNNING BELT ADJUSTMENT

• Adjust speed to 1.86 mph.
• If the running belt is deflecting to the right, adjust the bolt on the right one-half turn clockwise using the Allen key, and adjust the bolt on the left one-half turn anti-clockwise (see pic 1)
• If the running belt is deflecting to the left, adjust the bolt on the left one half turn clockwise using the Allen key, and adjust the bolt on the right one-half turn anti-clockwise (see pic 2)
• If the running belt is not deflected, but is slipping, adjust both left and right bolts one-half turn clockwise to tighten, or one-half turn anti-clockwise to loosen if the belt is too tight. (See pic 3 and 4)
• After adjustment, check the running belt, and adjust further if required.

OVERVIEW DRAWING

PARTS LIST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>