Ponek S821 WiFi Thermal Printer User Manual

Ponek S821 WiFi Thermal Printer User Manual

Package Contents

• Printer*1

• Printing paper*1

• Adapter x1

• Data Cable*1

• Quick Start Guide*1

Attention: All pictures in this instruction manual are for illustration purposes only. The actual product may vary due to product enhancement.

Printer Components

Warning

1. Please use our official power adapter to ensure the quality of your printing.
2. Please do not touch the print head as an overheated print head may cause undesirable burns.
3. The paper cutter is very sharp. Please be careful when handling it. (Only applies to models with paper cutters)
4. Please connect to your 2.4 GHz WiFi. (5 GHz is currently not supported)
5. When printing, please do not pull the paper by force to prevent affecting your printing experience.
6. The optimum working temperature for the printer is around 0°C-40°C. The too-high or too-low temperature may affect the printing quality.

Instructions

1. Open the cover by pressing the Open Cover Buttons on the two sides of the printer.
   

2. Take out a random paper roll and tear the edge of the paper roll.
   

3. Install the paper roll back into the paper compartment and pull the paper out of the Paper Output Slot. Close the Cover
   

Hint: How to differentiate the front and back of the printing paper

1. Take a piece of printing paper and scratch both sides of the paper with your fingernails. The front side is the side with colors. Install the paper with the front side facing upward.
2. Our product can print paper in different sizes. Please adjust the paper holder on the right to match the width of the printing paper.
3. To achieve the best result, please use our genuine printing paper.

Connect to App

Step 1: Please search for “Phomemo” on your s phone’ app market and download the App.

Step 2: Turn on the printer, open the app, and connect to the printer by following the instructions on the App

Step 3: Choose the file you want to print on the App. You may check the print preview and start printing.

Warning:

1. Please ensure your Bluetooth is turned on. Make sure to put your phonenear the printer.
2. If you’ re connecting through WiFi, please connect to the 2.4 GHz WiFi, not the 5 GHz WiFi.

Connect to the computer

Step 1: Connect one end of the data cable to your computer and the other end to the printer’ s USB port. Connect your printer to a power source and turn on your printer.
Step 2: Enter our official website and download the printer’ s drivers. Install the printer’ s driver.
Official website: http://S821.phomemo.com/
Step 3: Add the printer to your computer and establish a connection. Once the connection is established, you can print your documents from your computer. Tip: If you wish to obtain more tutorials on how to install the driver, please open your Phomemo APP > Profile > Use Tutorial to obtain more guidance

Printer State

Printer
State| Turning on the printer| Indicator Light (Power) — Red, Green & White (Flashing)
Printing| Indicator Light (Power) — Green (Flashing)
Idle State (Including after printing, installing paper rolls, closing the cover or paper compartment)| Indicator Light (Power) — Green (Lit)
Turning off the printer| Indicator Light (Power) — Off
Upgrading Firmware| Indicator Light (Power) — Red & Green (Alternating Flashing)
Abnormal
State| Print Head overheated| Indicator Light (Power) — Red (Flashing)
Out of Paper/ Unable to detect paper| Indicator Light (Power) — Red (Lit)
Incorrect RFID
Printer’ s Cover Open
Connection
State| WiFi Connecting| Indicator Light (WiFi) — White (Flashing)
USB Cable Connecting
WiFi Connected| Indicator Light (WiFi) — White (Lit)
Disconnecting| Indicator Light (WiFi) — White (Flash three times)

Official printing paper type

Normal thermal paper: Does not contain Bisphenol-A. Writable Quick-drying thermal paper: Thermal paper that does not contain Bisphenol-A, can be written on, and dries ink quickly.

• The printing papers mentioned above are official printing papers.
• Any issues with your printer arising from using non-official printing papers will not be covered under our warranty policy.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body.

IC Caution

Radio Standards Specification RSS-Gen, issue 5- English:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.

RF exposure statement:

The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Warranty Card

Product certification

• Inspector:
• Delivery date:

Documents / Resources

| Ponek S821 WiFi Thermal Printer [pdf] User Manual
S821 WiFi Thermal Printer, S821, WiFi Thermal Printer, Thermal Printer, Printer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>