BOSCH GWX 18V-15 PSC Professional Angle Grinder Instruction Manual
- June 17, 2024
- Bosch
Table of Contents
GWX 18V-15 PSC Professional Angle Grinder
Instruction Manual GWX Professional
HEAVY DUTY
18V-15 C | 18V-15 SC | 18V-15 P | 18V-15 PSC
GWX 18V-15 PSC Professional Angle Grinder
|
---|---
|
Safety Instructions
General Power Tool Safety Warnings
WARNING
Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
- Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
- Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. u Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
- Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
- Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Safety warnings for angle grinder
Safety warnings common for grinding, sanding, wire brushing or cutting-off
operations:
- This power tool is intended to function as a grinder, sander, wire brush, hole cutter or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
- Operations such as polishing are not to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
- Do not convert this power tool to operate in a way which is not specifically designed and specified by the tool manufacturer. Such a conversion may result in a loss of control and cause serious personal injury.
- Do not use accessories which are not specifically designed and specified by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
- The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
- The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled. u The dimensions of the accessory mounting must fit the dimensions of the mounting hardware of the power tool. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
- Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
- Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various applications. The dust mask or respirator must be capable of filtrating particles generated by the particular application. Prolonged exposure to high intensity noise may cause hearing loss.
- Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
- Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
- Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
- Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
- Do not operate the power tool near flammable materials. Sparks could ignite these materials.
- Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Kickback and related warnings:
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing
pad, brush or any other accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the uncontrolled power tool to
be forced in the direction opposite of the accessory’s rotation at the point
of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the
edge of the wheel that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb out or kick out. The wheel
may either jump toward or away from the operator, depending on direction of
the wheel’s movement at the point of pinching. Abrasive wheels may also break
under these conditions. Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be avoided by taking
proper precautions as given below.
- Maintain a firm grip with both hands on the power tool and position your body and arms to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
- Never place your hand near the rotating accessory. Accessory may kickback over your hand.
- Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging.
- Use special care when working corners, sharp edges, etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
- Do not attach a saw chain woodcarving blade, segmented diamond wheel with a peripheral gap greater than 10 mm or toothed saw blade. Such blades create frequent kickback and loss of control.
Safety warnings specific for grinding and cutting-off operations:
- Use only wheel types that are specified for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
- The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
- The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.
- Wheels must be used only for specified applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
- Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
- Do not use worn down wheels from larger power tools. A wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.
- When using dual purpose wheels always use the correct guard for the application being performed. Failure to use the correct guard may not provide the desired level of guarding, which could lead to serious injury.
Additional safety warnings specific for cutting-off operations:
- Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
- Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.
- When the wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold it motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.
- Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
- Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
- Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
- Do not attempt to do curved cutting. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage, which can lead to serious injury. Safety warnings specific for sanding operations:
- Use proper sized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending too far beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
Safety warnings specific for wire brushing operations:
- Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush The wire bristles can easily penetrate light clothing and/or skin.
- If the use of a guard is specified for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.
Additional safety information
Wear safety goggles.
The protective guard must not be used for cutting. With a suitable adapter,
the protective guard can also be used for cutting.
Hold the power tool firmly with both hands and make sure you have a stable
footing. The power tool can be more securely guided with both hands.
- Use suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to explosion. Breaking water pipes causes property damage.
- Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working.
- Release the On/Off switch and set it to the Off position when the power supply is interrupted, e.g. when the battery pack is removed. This prevents uncontrolled restarting.
- Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.
- Store the application tools inside buildings, in a dry, frost-free room at a uniform temperature.
- Remove the application tools before transporting the power tool. This will allow you to avoid damage. u Bonded cutting and grinding discs have an expiration date, after which the discs must no longer be used.
- In case of damage and improper use of the battery, vapours may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.
- Do not open the battery. There is a risk of short-circuiting.
- The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.
- Only use the battery in the manufacturer’s products. This is the only way in which you can protect the battery against dangerous overload.
Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short- circuiting.
- Caution! When using the power tool with Bluetooth®, a fault may occur in other devices and systems, aero planes and medical devices (e.g. pacemakers, hearing aids). Also, damage to people and animals in the immediate vicinity cannot be completely excluded. Do not use the power tool with Bluetooth® in the vicinity of medical devices, petrol stations, chemical plants, areas with a potentially explosive atmosphere or in blasting areas. Do not use the power tool with Bluetooth® in aircraft. Avoid using the product near your body for extended periods. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Robert Bosch Power Tools GmbH is under license.
Product Description and Specifications
Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric
shock, fire and/or serious injury. Please observe the illustrations at the
beginning of this operating manual.
Intended use
The power tool is intended for cutting and brushing metal, stone, plastic and
composite materials, roughing metal, plastic and composite materials as well
as making holes in stone materials using diamond annular cutters, without the
use of water. Make sure that the correct protective guard is used (see
“Operation”, page 33).
Sufficient dust extraction must be provided when cutting stone.
With approved abrasive tools, the power tool can be used for sanding with
sanding discs.
The power tool must not be used to grind stone materials with diamond grinding
heads.
(GWX 18V-15 C / GWX 18V-15 SC / GWX 18V-15 PSC)
With the Bluetooth® Low Energy Module GCY 42 (not included with the
product as standard) inserted, power tool data and settings can be transferred
between the power tool and a mobile device by means of Bluetooth® wireless
technology.
Product features
The numbering of the product features refers to the diagram of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
(3) Lever
(4) User interface (GWX 18V-15 SC / GWX 18V-15 PSC)
(5) On/off switch (GWX 18V-15 C / GWX 18V-15 SC)
(6) Cover (for Bluetooth® Low Energy Module GCY 42 a) for GWX 18V-15 C, GWX
18V-15 SC, GWX 18V-15 PSC)
(7) Rechargeable battery a)
(8) Rechargeable battery release button a)
(9) On/off switch (GWX 18V-15 P / GWX 18V-15 PSC) (10) Unlocking lever for
on/off switch (GWX 18V-15 P / GWX 18V-15 PSC)
(11) Standard auxiliary handle (insulated gripping surface) a)
(12) Vibration-damping auxiliary handle (insulated gripping surface)
(13) X-LOCK disc brush a)
(14) X-LOCK conical brush a)
(15) Protective guard for grinding
(16) X-LOCK grinding disc/flap disc a)
(17) Protective guard for cutting a)
(18) Cover for cutting| (19) X-LOCK cutting disc a)
(20) X-LOCK diamond cutting disc a)
(21) X-LOCK holder
(22) Hand guard a)
(23) X-LOCK backing pad for fibre discs a)
(24) X-LOCK fibre disc a)
(25) X-LOCK clip for fibre discs a)
(26) X-LOCK cup brush a)
(27) X-LOCK diamond core cutter a)
(28) Handle (insulated gripping surface)
(29) Extraction guard for cutting with cutting guides a)
(30) Battery charge indicator (user interface)
(31) Kickback shutdown indicator (user interface)
(32) Speed preselection button (user interface)
(33) Speed setting/mode indicator (user interface)
(34) Smartphone symbol (user interface)
(35) Power tool status indicator (user interface)
(36) Temperature indicator (user interface)
---|---
a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
Technical Data
Angle grinder| | GWX 18V-15 C| GWX 18V-15 S| GWX 18V-15 P|
GWX 18V-15 PSC
---|---|---|---|---|---
Article number| | 3 601 JH6 4..| 3 601 JH6 5..| 3 601 JH6 F..| 3 601 JH6 G..
Rated voltage| V=| 18| 18| 18| 18
Rated no-load speed”‘| min’| 11,000| 11,000| 11,000| 11,000
No-load speed’)| min”| 9800| 3400-9800| 9800| 3400-9800
Max. grinding disc diameter/rubber sanding pad diameter| mm| 125| 125| 125|
125
Kick Back Control| | •| •| •| •
Restart protection| | •| •| •| •
Run-out brake| | •| •| •| •
Drop Control| | •| •| •| •
Speed preselection| | | •| | •
Weight according to EPTA-Procedure 01:20140| kg| 2.4-3.8| 2.5-3.8| 2.5-3.8|
2.5-3.8
Recommended ambient temperature during charging| °C| 0 to +35| 0 to +35| 0 to
+35| 0 to +35
Permitted ambient temperature dur- ing operation()) and during storage| °C|
-20 to +50| -20 to +50| -20 to +50| -20 to +50
Compatible rechargeable batteries| | GBA 18V… ProCORE18V…| GBA 18V…
ProCORE18V…| GBA 18V… ProCORE18V…| GBA 18V… ProCORE18V…
Recommended rechargeable batter- ies for maximum performance| | ProCORE18V…
5.5 Ah| ProCORE18V…
5.5 Ah| ProCORE18V…
5.5 Ah| ProCORE18V…
5.5 Ah
Angle grinder| | GWX 18V-15 C| GWX 18V-15 S| GWX 18V-15 P| GWX 18V-15 PSC
---|---|---|---|---|---
Article number| | 3 601 JH6 4..| 3 601 JH6 5..| 3 601 JH6 F..| 3 601 JH6 G..
Rated voltage| V=| 18| 18| 18| 18
Rated no-load speed”‘| min’| 11,000| 11,000| 11,000| 11,000
No-load spee’)| min”| 9800| 3400-9800| 9800| 3400-9800
Max. grinding disc diameter/rubber sanding pad diameter| mm| 125| 125| 125| 125
Kick Back Control| | •| •| •| •
Restart protection| | •| •| •| •
Run-out brake| | •| •| •| •
Drop Control| | •| •| •| •
Speed preselection| | | •| | •
Weight according to EPTA-Proced- ure 01:20140| kg| 2.4-3.8| 2.5-3.8| 2.5-3.8| 2.5-3.8
Recommended ambient temperature during charging| °C| 0 to +35| 0 to +35| 0 to +35| 0 to +35
Permitted ambient temperature dur- ing operation()) and during storage| °C| -20 to +50| -20 to +50| -20 to +50| -20 to +50
Compatible rechargeable batteries| | GBA 18V… ProCORE18V…| GBA 18V… ProCORE18V…| GBA 18V… ProCORE18V…| GBA 18V… ProCORE18V…
Recommended rechargeable batter- ies for maximum performance| | ProCORE18V…
5.5 Ah| ProCORE18V…
5.5 Ah| ProCORE18V…
5.5 Ah| ProCORE18V…
5.5 Ah
Recommended chargers| | GAL 18…
GAX 18…
GAL 36…| GAL 18…
GAX 18…
GAL 36…| GAL 18…
GAX 18…
GAL 36…| GAL 18…
GAX 18…
GAL 36…
Data transfer E)
Bluetooth® F)| | Bluetooth® 4.2
(Low Energy)| Bluetooth® 4.2
(Low Energy)| Bluetooth® 4.2
(Low Energy)| Bluetooth® 4.2
(Low Energy)
Signal interval| s| 8| 8| 8| 8
Max. signal range G)| m| 30| 30| 30| 30
A) Rated no-load speed for the selection of appropriate application tools in
accordance with EN IEC 62841-2-3. The actual no-load speed is lower for safety
reasons and according to production tolerances.
B) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah and
depending on the battery’s state of charge as well as the tool’s operating
temperature
C) Depends on rechargeable battery (7), protective guard ((17), (15),
(18)) and auxiliary handle ((11), (12)) in use
D) Limited performance at temperatures < 0 °C
E) Bluetooth ® Low Energy Module GCY 42 not included with the
product as standard
F) The mobile devices must be compatible with Bluetooth® Low Energy devices
(version 4.2) and support the Generic Access Profile (GAP).
G) The signal range may vary greatly depending on external conditions,
including the receiving device used. The Bluetooth® range may be significantly
weaker inside closed rooms and through metallic barriers (e.g. walls, shelving
units, cases, etc.).
Values can vary depending upon the product and are subject to application and
environmental conditions. For further information www.bosch-
professional.com/wac.
Noise/Vibration Information
| ■| GWX 18V-15 C| GWX 18V-15 SC| GWX 18V-15 P| GWX 18V-15 PSC
---|---|---|---|---|---
| | 3 601 JH6 4..| 3 601 JH6 5..| 3 601 JH6 F..| 3 601 JH6 G..
Noise emission values determined according to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!| dB(A)
dB(A)
dB| 92
100
3| 92
100
3| 94
102
3| 94
102
3
Vibration total values ah (triax vector sum) and uncertainty K determined
according to EN IEC 62841-2-3:
Grinding surfaces (roughing) and abrasive cutting:
ah
K| m/s²
m/s²| 6.4
1.5| 6.4
1.5| 5.5
1.5| 5.5
1.5
Disc sanding: A)
ah
K| m/s²
m/s²| <2.5
1.5| <2.5
1.5| <2.5
1.5| <2.5
1.5
A) determined with medium-hard backing pad
Grinding thin metal sheets or other materials that tend to easily vibrate with
a large surface area can cause the noise emission value to increase by up to
15 dB. Suitable, heavy damping mats can reduce the increased noise emissions.
Increased noise emissions must be taken into consideration, both for the risk
assessment of the noise output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these instructions have
been measured in accordance with a standardised measuring procedure and may be
used to compare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions. The stated vibration level and
noise emission value represent the main applications of the power tool.
However, if the power tool is used for other applications, with different
accessories or is poorly maintained, the vibration level and noise emission
value may differ. This may significantly increase the vibration and noise
emissions over the total working period.
To estimate vibration and noise emissions accurately, the times when the tool
is switched off or when it is running but not actually being used should also
be taken into account.
This may significantly reduce vibration and noise emissions over the total
working period.
Implement additional safety measures to protect the operator from the effects
of vibration, such as servicing the power tool and accessories, keeping their
hands warm, and organizing workflows correctly.
Kickback stop
If there is a sudden kickback in the power tool, e.g. jamming in a separating
cut, the power supply to the motor will be interrupted electronically. The
kickback stop indicator(31) then lights up. When kickback stop is activated,
the status indicator (35) flashes red.
To restart the tool, set the on/off switch (5) / (9) to the “off” position
and then switch the power tool on again.
Restart protection
The restart protection feature prevents the power tool from uncontrolled
starting after the power supply to it has been interrupted.
To restart the tool, set the on/off switch (5) / (9) to the “off” position and
then switch the power tool on again.
Impact shutdown
The integrated impact shutdown switches the power tool off as soon as it hits
the floor. The status indicator (35) then flashes red. To restart the
tool, set the on/off switch (5) / (9) to the “off” position and then
switch the power tool on again.
Run-out brake
The power tool is fitted with the electronic Bosch X Brake System. When it is
switched off, the abrasive tool is brought to a complete stop within a few
seconds. This means that the runout time is significantly shorter than for
angle grinders without a run-out brake and enables the power tool to be set
down sooner.
User interface (see figure E)
(GWX 18V-15 SC / GWX 18V-15 PSC)
The user interface (4) is used to preselect the speed and to indicate the
status of the power tool.
Speed preselection
(GWX 18V-15 SC / GWX 18V-15 PSC)
Note: Individually adjustable speed presetting with up to 6 speed levels is
only available when the Bluetooth® Low Energy Module GCY 42 (not included with
the product as standard) is inserted.
In the default setting, 3 speed levels are preset. A special application
(Bosch Toolbox App) can be used to program up to 6 speed levels.
If the number of speed levels is changed, the values of the individual levels
are adjusted by default. In this case, the speed level/mode indicator (33)
lights up white. When a speed value is programmed individually, the speed
level/mode indicator (33) lights up blue at this speed level (i.e. not
according to a default setting). The individual adaptation of speed levels is
possible in steps of 200 min-1 each. Observe the ascending logic of the steps
(2 ≥ 1 / 3 ≥ 2 etc).
The information in the tables below describes the preset speeds (default
settings) for each programmed number of levels.
GWX 18V-15 SC
GWX 18V-15 PSC| Basic speed setting at level
---|---
1| 2| 3| 4| 5| 6
[min-¹]| [min-¹]| [min-¹]| [min-¹]| [min-¹]|
[min-¹]
Number of speed settings| | | | |
2| 3400| 9800| –| –| –| –
3| 3400| 6600| 9800| –| –| –
4| 3400| 5600| 7600| 9800| –| –
5| 3400| 5000| 6600| 8200| 9800| –
6| 3400| 4600| 6000| 7200| 8600| 9800
The specified speed setting values depend on the rechargeable battery in use,
the battery’s state of charge and the tool’s operating temperature.
You can use the button for speed preselection (32) to preselect the
required speed, even during operation. The information in the table below
describes the recommended values for the default settings with 3 preset speed
levels.
Material| Application| Application tool| Speed
preselection
level| GWX 18V-15 SC
GWX 18V-15 PSC
[min-¹]
---|---|---|---|---
Metal| Removing paint| Sanding sheet| 1| 3400
Metal| Brushing, removing rust| Cup brush, abrasive disc| 1| 3400
Stainless steel| Grinding| Grinding disc/fibre disc| 2| 6600
Metal| Rough grinding| Grinding disc| 3| max.
Metal| Cutting| Cutting disc| 3| max.
Stone| Cutting| Diamond cutting disc| 3| max.
- The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
Rechargeable battery
Bosch sells some cordless power tools without a rechargeable battery. You can tell whether a rechargeable battery is included with the power tool by looking at the packaging.
Charging the battery
- Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.
Note: Lithium-ion rechargeable batteries are supplied partially charged according to international transport regulations. To ensure full rechargeable battery capacity, fully charge the rechargeable battery before using your tool for the first time.
Inserting the Battery
Push the charged battery into the battery holder until it clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery release button and pull
the battery out.
Do not use force to do this. The rechargeable battery has two locking levels
to prevent the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in place by a spring
when fitted in the power tool.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the state of charge of
the battery. For safety reasons, it is only possible to check the state of
charge when the power tool is not in operation.
Press the button for the battery charge indicator on or to show the state
of charge. This is also possible when the battery is removed.
If no LED lights up after pressing the button for the battery charge
indicator, then the battery is defective and must be replaced.
The state of charge of the battery is also displayed on the user interface
(see “Status indicators”, page 35).
Battery model GBA 18V…
LED | Capacity |
---|---|
3× continuous green light | 60–100 % |
2× continuous green light | 30–60 % |
1× continuous green light | 5–30 % |
1× flashing green light | 0–5 % |
Battery model ProCORE18V…
LED | Capacity |
---|---|
5 × continuous green light | 80–100 % |
4 × continuous green light | 60–80 % |
3 × continuous green light | 40–60 % |
2 × continuous green light | 20–40 % |
1 × continuous green light | 5–20 % |
1 × flashing green light | 0–5 % |
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to 50 °C. Do not
leave the battery in your car in the summer, for example.
Occasionally clean the ventilation slots on the battery using a soft brush
that is clean and dry.
A significantly reduced operating time after charging indicates that the
battery has deteriorated and must be replaced. Follow the instructions on
correct disposal.
Fitting
Inserting the Bluetooth ® Low Energy Module GCY 42 (Accessory)
Note: The Bluetooth ® Low Energy Module GCY 42 is avail- able as an accessory
with GWX 18V-15 C, GWX 18V-15 SC and GWX 18V-15 PSC power tools. Read the
corresponding operating instructions for information about the Bluetooth ® Low
Energy Module GCY 42.
Fitting Protective Equipment
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
Note: If the grinding disc breaks during operation or the holding fixtures on the protective guard/power tool become damaged, the power tool must be sent to the after-sales service immediately; see the “After-Sales Service and Application Service” section for addresses.
Protective guard for grinding
Place the protective guard (15) onto the holder on the power tool until
the coding cams of the protective guard are aligned with the holder. When
doing so, press and hold the unlocking lever (1).
Press the protective guard (15) onto the spindle collar until the shoulder
of the protective guard is sitting on the flange of the power tool and rotate
the protective guard until it audibly clicks into place.
Adjust the position of the protective guard (15) to meet the requirements
of the operation. To do this, push the unlocking lever (1) upward and
rotate the protective guard (15) into the required position.
- Always position the protective guard (15) such that the two cams on the unlocking lever (1) engage in the corresponding openings on the protective guard (15).
- Adjust the protective guard (15) such that sparking in the direction of the operator is prevented.
- The protective guard (15) must only be able to be rotated in the direction of the accessory while the unlocking lever (1) is actuated. Otherwise, the power tool must not be used any more under any circumstances and must be sent to the after-sales service.
Note: The coding cams on the protective guard (15) ensure that only a protective guard that is suitable for the power tool can be fitted.
Protective guard for cutting
- For cutting, always use the protective guard for cutting (17) or the protective guard for grinding (15) together with the cover for cutting (18).
- Provide sufficient dust extraction when cutting stone.
The protective guard for cutting (17) is fitted in the same way as the protective guard for grinding (15).
Metal cover for cutting
Fit the metal cover for cutting (18) on the protective guard for grinding (15) (see figure A): Swivel the tool retainer back (➊). Attach the cover (18) to the protective guard for grinding (15) (➋). Press the tool retainer firmly into place on the protective guard (15) (➌). To remove the cover (see figure B), press the button on the tool retainer (➊) and swivel it back (➋). Remove the cover (18) from the protective guard (15) (➌). Plastic cover for cutting Attach the plastic cover for cutting (18) to the protective guard for grinding (15) (see figure C). The cover (18) audibly and visually engages on the protective guard (15). To remove the cover (see figure D), unlock the cover (18) on the left- or right-hand side of the protective guard (15) (➊) and remove the cover (➋).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (29) is fitted in the same
way as the protective guard for grinding (15).
Hand guard
-
Always fit the hand guard (22) when working with the rubber sanding pad (23) or with the cup brush/conical brush/diamond annular cutter.
Attach the hand guard (22) to the side handle (11).
Standard auxiliary handle/low-vibration auxiliary handle Screw the auxiliary handle (11)/(12) on the right or left of the machine head depending on the working method. -
Do not operate your power tool without the auxiliary handle (11)/(12).
-
Do not continue to use the power tool if the auxiliary handle (11)/(12) is damaged. Do not make any alterations to the auxiliary handle (11)/(12).
The low-vibration auxiliary handle (12) reduces vibration, enabling the tool to be used safely and more comfortably.
Fitting and removing abrasive tools
Follow the special assembly instructions for X-LOCK application tools.
-
Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
-
Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working.
-
Only use original X-LOCK application tools that carry the X-LOCK logo. A maintained clamping gauge of max.
1.6 mm can only be guaranteed with original X-LOCK application tools. A higher clamping gauge can lead to insecure clamping, potentially causing the clamp tool to come loose. -
X-LOCK application tools do not need additional clamping flanges or support flanges.
-
Make sure that the application tool and the holder are not deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that both X-LOCK catches are open (see figure below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK catches.
Fitting the abrasive tool
- Place the grinding/cutting/flap disc in a central position on the X-LOCK holder, parallel to the bearing surface and with the right side facing up.
- Push the disc into the holder.
- The disc audibly clicks into place. Do not actuate the lever (3) when doing so.
- After fitting, check that the edge of the abrasive tool
(➍) is fitted correctly, i.e. is no higher than the reference surface
(➎). If the edge is higher than the reference surface, either the holder must be cleaned or the abrasive tool must not be used.
Before removing the grinding/cutting/flap disc: Make sure that the power tool has come to a complete stop.
Removing the abrasive tool
➊ Open the lever (3).
➋ The grinding/cutting/flap disc will be released.
➌ The grinding/cutting/flap disc can be removed.
Approved abrasive tools
You can use all the abrasive tools mentioned in these operating instructions.
The permissible speed[min-1 ] or the circumferential speed [m/s] of the
abrasive tools used must at least match the values given in the table.
It is therefore important to observe the permissible
rotational/circumferential speed on the label of the abrasive tool.
max. [mm]| [°]| |
---|---|---|---
| D| b| s| α| |
| 125| 7.2| –| –| 11,000| 80
| 125| 4.2| –| –| 11,000| 80
| 125| –| –| –| 11,000| 80
| 75| 30| –| –| 11,000| 80
| 125| 19| –| –| 11,000| 80
| 125| –| –| –| 11,000| 80
| 83| –| –| –| 11,000| 80
| 125| 6| 10| > 0| 11,000| 80
Rotating the machine head (see figure G)
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch. The machine head can be rotated in 90° increments. In this way, the on/off switch can be brought into a more favorable handling position for particular applications, e.g. for lefthanded tool users.
Completely unscrew the four screws (➊). Rotate the machine head carefully, without removing it from the housing, into the new position (➋). Screw in and retighten the four screws (➌).
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some wood types,
minerals and metal can be harmful to one’s health. Touching or breathing-in
the dust can cause allergic reactions and/or lead to respiratory infections of
the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carcinogenic,
especially in connection with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may only be worked by
specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the materials to be
worked.
- Avoid dust accumulation at the workplace. Dust can easily ignite.
Operation
- The power tool with inserted Bluetooth ® Low Energy Module GCY 42 is equipped with a radio interface. Local operating restrictions, e.g. in aircraft or hospitals, must be observed.
- In areas in which the Bluetooth® wireless technology must not be used, the Bluetooth® Low Energy Module GCY 42 and the coin cell must be removed.
- Do not load the power tool so heavily that it comes to a stop.
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
- Exercise caution when cutting slots in structural walls; see the “Information on structural design” section.
- Clamp the workpiece if it is not secure under its own weight.
- If the power tool has been subjected to a heavy load, continue to run it at no-load for several minutes to cool down the accessory.
- Do not use the power tool with a cut-off stand.
- Do not touch grinding and cutting discs until they have cooled down. The discs can become very hot while working.
If the power tool becomes electrostatically charged, the built-in electronics
will switch the power tool off. To restart the power tool. press the on/off
switch (5) again or push the unlocking lever (10) to the front and
then push the on/off
switch (9) upwards.
Practical advice
Rough grinding
- Always use the protective guard for grinding (15) when rough grinding with bonded abrasives.
- Never use cutting discs for rough grinding.
- When rough grinding, the protective guard for cutting (17) or the protective guard for grinding (15) with a fitted cover for cutting (18) can impact the workpiece and lead to a loss of control.
The best rough grinding results are achieved with a set angle of 30° to 40°. Move the power tool back and forth with moderate pressure. This will ensure that the workpiece does not become too hot or discolor and that grooves are not formed.
- The protective guard for cutting (17) or the protective guard for grinding (15) with a fitted cover for cutting (18) must be used when using bonded discs which are approved for cutting and grinding.
Surface grinding with flap disc
- Always use the protective guard for grinding (15) when grinding with the flap disc. The flap disc (accessory) enables you to machine curved surfaces and profiles. Flap discs have a considerably longer service life, lower noise levels and lower grinding temperatures than conventional grinding discs.
Surface grinding with sanding disc
- Always fit the hand guard (22) when working with the rubber sanding pad (23). Grinding with a sanding disc can be done without a protective guard. See the graphics page for fitting instructions.
Cup brush/disc brush/conical brush
- Always use the protective guard for grinding (15) when brushing with disc brushes. Brushing with cup brushes/conical brushes can be performed without the protective guard.
- Always fit the hand guard (22) when working with the cup brush or conical brush.
- The wires of the disc brush can get caught on the protective guard and break, if the maximum permitted dimensions of the disc brushes are exceeded. See the graphics page for fitting instructions.
Cutting Metal
- For cutting metal with bonded cutting discs or diamond cutting discs, always use the protective guard for cutting (17) or the protective guard for grinding (15) with a fitted cover for cutting (18).
- When using the protective guard for grinding (15) for cutting work with bonded cutting discs, there is an increased risk of being exposed to sparks, particles and disc fragments if the disc breaks.
When carrying out abrasive cutting, use a moderate feed that is suited to the material being machined. Do not exert pressure on the cutting disc and do not tilt or swing the power tool.
Do not attempt to reduce the speed of a cutting disc coming to a stop by applying pressure from the side.
The power tool must always work in an up-grinding motion. Otherwise there is a
risk that it will be pushed uncontrolled out of the cut. For best results when
cutting profiles and rectangular tubing, start at the smallest cross section.
Cutting stone
-
For cutting stone with bonded cutting discs or diamond cutting discs for concrete/stone, always use the extraction guard for cutting with a cutting guide (29) or the protective guard for cutting (17) or the protective guard for grinding
(15) with a fitted cover for cutting (18). -
Provide sufficient dust extraction when cutting stone.
-
Wear a dust mask.
-
The power tool may be used only for dry cutting/grinding.
-
When using the protective guard for cutting (17) , the protective guard for grinding (15) or the protective guard for grinding (15) with a fitted cover for cutting (18) for cutting and grinding applications in concrete or masonry, there is an increased dust load and an increased risk of losing control of the power tool, which can lead to kickback.
For cutting stone, it is best to use a diamond cutting disc. When using the
extraction guard for cutting with a cutting guide (29), the dust extractor
must be approved for extracting stone dust. Suitable dust extractors are
available from Bosch. Switch on the power tool and position it with the front
part of the cutting guide on the workpiece. Move the power tool with a
moderate feed motion that is suited to the material being machined.
When cutting especially hard materials such as concrete with a high pebble
content, the diamond cutting disc can overheat and become damaged as a result.
This is clearly indicated by circular sparking, rotating with the diamond
cutting
disc.
If this happens, stop cutting and allow the diamond cutting disc to cool down
by running the power tool for a short time at maximum speed with no load.
If work is noticeably slower and with circular sparking, this indicates that
the diamond cutting disc has become blunt. You can resharpen the disc by
briefly cutting into abrasive material (e.g. lime-sand brick).
Cutting other materials
- For cutting materials such as plastic, composite materials, etc. with bonded cutting discs or Carbide Multi Wheel cutting discs, always use the protective guard for cutting (17) or the protective guard for grinding (15) with a fitted cover for cutting (18). You can achieve improved dust extraction by using the extraction guard with a cutting guide (29).
Working with Diamond Annular Cutters
- Only use dry diamond annular cutters.
- Always fit the hand guard (22) when working with diamond annular cutters.
Do not place the diamond annular cutter parallel to the workpiece. Plunge it into the workpiece at an angle and in a circular motion. This will allow you to achieve optimal cooling and ensure a longer tool life for the diamond annular cutter.
Information on structural design
Recesses in load-bearing walls are subject to country-specific regulations. These regulations must be observed under all circumstances. Seek advice from the responsible structural engineer, architect or construction supervisor before starting work.
Start-up
Switching on/off
(GWX 18V-15 C / GWX 18V-15 SC)
To start the power tool, push the on/off switch (5) forward.
To lock the on/off switch (5) in position, push the on/off switch (5)
forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (5); or, if the
switch is locked, briefly push the on/off switch (5) backward and down and
then release it.
- Always check abrasive tools before using them. The abrasive tool must be fitted properly and be able to move freely. Carry out a test run for at least one minute with no load. Do not use abrasive tools that are damaged, run untrue or vibrate during use. Damaged abrasive tools can burst apart and cause injuries.
Switching On/Off
(GWX 18V-15 P / GWX 18V-15 PSC)
To start the power tool, push the unlocking lever (10) forwards and then push the on/off switch (5) up. To switch off the power tool, release the on/off switch (5).
- Always check abrasive tools before using them. The abrasive tool must be fitted properly and be able to move freely. Carry out a test run for at least one minute with no load. Do not use abrasive tools that are damaged, run untrue or vibrate during use. Damaged abrasive tools can burst apart and cause injuries.
Status indicators
Battery charge indicator (user interface) (30)| Meaning/cause|
Solution
---|---|---
Green| Battery charged| –
Yellow| Battery charged| Replace or charge battery soon
Red| Battery empty| Replace or charge battery
Power tool status indicator (35)| Meaning/cause| Solution
Green| Status OK|
Yellow| Critical temperature has been reached or rechargeable battery is
almost empty| Run the power tool at no load and allow it to cool down, or
replace or charge the battery soon
Illuminated red| Power tool has overheated or battery is empty| Allow the
power tool to cool down, or replace or charge the battery
Flashing red| Kickback shutdown, restart protection or impact shutdown has
been triggered| Switch the power tool off and on again
Flashing blue| (GWX 18V-15 C / GWX 18V-15 SC / GWX 18V-15 PSC) A) : Power
tool is connected to a mobile device or settings are being transferred| –
A) Bluetooth ® Low Energy Module GCY 42 not included with the product as
standard
Temperature indicator (36)| Meaning/cause| Solution
Yellow| Critical temperature has been reached (motor, electronics, battery)|
Run the power tool at no load and allow it to cool down
Red| Power tool is overheated and will switch off| Leave the power tool to
cool down
Smartphone symbol (34)| Meaning/cause
–| (GWX 18V-15 C / GWX 18V-15 SC / GWX 18V-15 PSC)A) : Further information can
be found under the “Power tool status” display on a mobile device if it is
connected via Bluetooth® wireless technology.
Connectivity functions
(GWX 18V-15 C / GWX 18V-15 SC / GWX 18V-15 PSC)
In conjunction with the Bluetooth® Low Energy module GCY 42 (not included with
the product as standard), the following connectivity functions are available
for the power tool:
– Registration and personalization
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for information about the
Bluetooth® Low Energy Module GCY 42 (not included with the product as
standard).
The connection of the power tool with the app must be confirmed by pressing
the speed preselection button (32) on the user interface (4). The app
requests this when connecting.
Maintenance and Service
Maintenance and Cleaning
- Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.
- To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean. Store and handle the accessories carefully. After-Sales Service and Application Service Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the
10‑digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts
or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at: www.bosch-
pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legislation on the
transport of dangerous goods. The user can transport the batteries by road
without further requirements.
When shipping by third parties (e.g.: by air transport or forwarding agency),
special requirements on packaging and labelling must be observed. For
preparation of the item being shipped, consulting an expert for hazardous
material is required.
Dispatch battery packs only when the housing is undamaged. Tape or mask off
open contacts and pack up the battery in such a manner that it cannot move
around in the packaging. Please also observe the possibility of more detailed
national regulations.
Disposal
Power tools, rechargeable batteries, accessories and packaging should be
sorted for environmental-friendly recycling.
Do not dispose of power tools and batteries/rechargeable batteries into
household waste!
Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic
equipment and its transposition into national law, power tools that are no
longer usable, and, according to the Directive 2006/66/EC, defective or
drained batteries must be collected separately and disposed of in an
environmentally correct manner.
If disposed incorrectly, waste electrical and electronic equipment may have
harmful effects on the environment and human health, due to the potential
presence of hazardous substances.
Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013
(SI 2013/3113) (as amended) and the Waste Batteries and Accumulators
Regulations 2009 (SI 2009/890) (as amended), products that are no longer
usable must be collected separately and disposed of in an environmentally
friendly manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see “Transport”, page
36).
Licenses
Copyright © 2004 – 2020, Texas Instruments Incorporated
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
– Neither the name of Texas Instruments Incorporated nor the names of its
contributors may be used to endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS”
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2009–2020 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
– Neither the name of ARM nor the names of its contributors may be used to
endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS”
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2011 Petteri Aimone
This software is provided ‘as-is’, without any express or implied warranty. In
no event will the authors be held liable for any damages arising from the use
of this software.
Permission is granted to anyone to use this software for any purpose,
including commercial applications, and to alter it and redistribute it freely,
subject to the following restrictions:
- The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
- Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
- This notice may not be removed or altered from any source distribution.
Warranty Disclaimer
This product contains Open Source Software components which underly Open
Source Software Licenses. Please note that Open Source Licenses contain
disclaimer clauses. The text of the Open Source Licenses that apply are
included in this manual under “Licenses”.
EU Declaration of Conformity
Angle grinder| Angle grinder| |
---|---|---|---
GWX 18V-15 C
GWX 18V-15 SC
GWX 18V-15 P
GWX 18V-15 PSC| 3 601 JH6 402
3 601 JH6 502
3 601 JH6 F02
3 601 JH6 G02| 2006/42/EC
2014/30/EU
2011/65/EU| EN 62841-1:2015+A11:2022
EN IEC 62841-2-3:2021+A11:2021
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
| * Robert Bosch Power Tools GmbH
(PT/ECS)
70538 Stuttgart
GERMANY
Thomas Donato
Chairman of the
Management Board| Helmut Heintzelman
Head of Product Certification
Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY
Stuttgart, 28.09.2023
Declaration of Conformity
Angle grinder
GWX 18V-15 C
GWX 18V-15 SC
GWX 18V-15 P
GWX 18V-15 PSC| Article number
3 601 JH6 402
3 601 JH6 502
3 601 JH6 F02
3 601 JH6 G02
---|---
We declare under our sole responsibility that the stated products comply with
all applicable provisions of the regulations listed below and are in
conformity with the following standards.
Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North
Orbital Road, Uxbridge UB9 5HJ, United Kingdom
| The Supply of Machinery (Safety) Regulations 2008
The Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
EN 62841-1:2015+A11:2022
EN IEC 62841-2-3:2021+A11:2021
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
| Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany
represented (in terms of the above regulations) by
Robert Bosch Limited, Broadwater Park, North Orbital Road,
Uxbridge UB9 5HJ, United Kingdom
Vonjy Rajakoba
Managing Director – Bosch UK| Martin Sibley
Head of Sales Operations and Aftersales
|
Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorised representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany
1 609 92A 8Z2 (2023.11) Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
References
- Invented for life | Bosch Global
- Početna strana | Bosch u Srbiji
- 巧米网为您服务!(QiaoMi.com)
- Skånevik Ølen Kraftlag AS
- ЕлектроінÑтрументи Bosch | Bosch Professional
- bosch-professional.com/wac
- ÐлектроинÑтрументы Bosch | Bosch Professional
- Bosch Power Tools | Bosch Power Tools
- Location selection | Bosch Power Tools
- Електроинструменти на Bosch | Електроинструменти на Bosch
- Service worldwide
- Home | Bosch Power Tools
- Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
- Bosch el-værktøj | Bosch el-værktøj
- Bosch-sähkötyökalut | Bosch-sähkötyökalut
- Outillage électroportatif Bosch | Outillage électroportatif Bosch
- Home | Bosch Power Tools
- Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
- Elektronarzędzia Bosch | Elektronarzędzia Bosch
- Scule electrice Bosch | Scule electrice Bosch
- Bosch električni alati | Bosch električni alati
- Bosch Услуги | Электроинструменты Bosch
- Elektrické náradie Bosch | Elektrické náradie Bosch
- Invented for life | Bosch Global
- Ana Sayfa | Bosch Türkiye
- Početna | Bosch u Hrvatskoj
- herramientasbosch.net
- bosch-professional.com/wac/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>