SEALEY PTB40506.V2 6 Drawer Hang On Chest Heavy Duty User Manual
- June 17, 2024
- SEALEY
Table of Contents
MSI MS-14F1 Prestige 14H Notebook PC
THANK YOU
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction manual
Wear protective gloves
SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop
practice regulations are adhered to when using this locker.
✔ Keep the work area clean, uncluttered and ensure there is adequate lighting.
✘ Keep the chest clean and tidy in accordance with good workshop practice.
✘ DO NOT use the chest for any purpose other than that for which it is
designed.
✘ DO NOT step on the drawers.
✘ DO NOT overload the chest.
✘ DO NOT clean the chest with any solvents which may damage the surfaces
or protective coating.
INTRODUCTION
Textured powder coat finish, both solvent and rust resistant. Ball bearing drawer slides provide superior performance and carry heavier loads, double sets on large drawers. All drawers have full width sand blasted aluminium ‘Lift & Latch’ drawer pulls, making easy access while preventing inadvertent opening when being moved. Non-slip drawer liners supplied for all drawers. Integral locking system locks all drawers with the turn of 1 key. Supplied with two keys. Hang-On chest suitable for heavy-duty Premier rollcabs.
SPECIFICATION
Model no. …………………………………………………PTB40506.V2
Overall size (W x D x H)……………………..405 x 460 x 885mm
ASSEMBLY
Refer to fig.1 and Parts Diagram
NOTE: Heavy item – get assistance to assemble.
NOTE: Minimum height of the rollcab top edge is 15mm and minimum depth of
rollcab is 460mm.
TOOLS REQUIRED : 10mm socket, ratchet, crosshead screwdriver.
INSTALL HANGER
Attach with countersink screw (3).
HANG CABINET fig.2
Fit protection pads (5).
Hang on the rollcab top.
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| 1 | M6x16mm hex bolt | 3 |
| 2 | Connector | 1 |
| 3 | M6x16mm countersink screw | 4 |
| 4 | Hanger | 1 |
| 5 | EVA pad | 2 |
| 6 | Slide Set | 7 sets |
| 7 | Drawer liner | 6 |
| 8 | Lock | 1 |
CONNECT THE CABINETS fig.3
Attach connecting piece (2) to locker with 2 x M6 x 16 hex head screw (1) and
rollcab with 1 x M6 x M16 hex head screw (1).
OPERATION
RAISE AND RELEASE DRAWER FRONTS
To open: lift up the drawer front whilst pulling towards you. To close: push
shut until the drawer closes.
If the drawer does not stay shut the hook may be bent or it may rub against
the drawer sides. To fix lightly bend the hook engages in the slide (above).
TO REMOVE DRAWERS
Pull drawer out so it is almost fully extended. Pull up the right hand black
release lever , whilst pushing down the left hand black release lever.
Whilst holding levers, as above, pull the draw outwards until it is released
from the slides.
TO REPLACE DRAWERS
Extend drawer slides. Insert brackets on each side of the drawer into the
slots in the cabinet slides, being careful that they are positioned properly.
Once properly inserted, completely close the drawer to set the slides in their
proper positions.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
CUSTOMER SUPPORT
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
[email protected]
www.sealey.co.uk
