Collomix Xo 20 NC Cordless mixer User Manual
- June 4, 2024
- Collomix
Table of Contents
Xo 20 NC Cordless mixer
User Manual
Xo 20 NC Cordless mixer
Technical data
| Xo 20 NC
---|---
Rated voltage| 18 V
Idle speed 1st gear| – 470 min-1
Idle speed 2nd gear| – 780 min-1
Speed under load, 1st gear| – 350 min-1
Speed under load, 2nd gear| – 580 min-1
Maximum paddle diameter| 140 mm
Paddle support| HEXAFIX
External thread of the agitator shaft| 5/8”
Max. mix amount| – 40 liters
Weight without a paddle, without a battery| 4.05 kg
Recommended CAS battery| 18 V, 5.2 Ah
- The unlocking mechanism for On/Off switch
- On/Off switch
- The unlocking mechanism for the battery
- Metal frame
- Handles
- Battery pack
- Rubber buffer
- Gear selector
- Agitator shaft
- HEXAFIX coupling
- Paddle
- Capacity indicator button
Intended use
The machine is intended for mixing liquid and powder building materials such
as paints, mortar, adhesives, plaster, and similar substances. The appropriate
paddle that offers the right mixing effect should be used based on the
consistency of the material and the quantity of material being mixed. The
total quantity of max. 30 kg/40 liters should not be exceeded per mixture. The
information in the technical data should be noted when selecting the paddle
type (diameter/mixing effect). Selecting an unsuitable mixing effect or paddle
diameter can overload the machine/drives and consequently lead to damage.
Please note that a paddle with a mixing effect from top to bottom puts a
greater strain on the power tool than vice versa.
Due to the high torque of the machine, it is not permitted for use as a drill.
It is not permitted to use the machine to prepare foodstuffs.
The machine is not suitable for mixing materials containing graphite dust,
brine or slurry. Mixing these substances can destroy the machine.
The user is solely responsible for damage caused by improper use.
Generally recognized accident prevention regulations and enclosed safety
instructions must be observed.
Device-Specific Safety Instructions
WARNING: Read all safety information, instructions, illustrations, and
technical data provided with this power tool. Failure to observe the safety
information and the following instructions may result in electric shock, fire,
and/or severe injuries.
Retain all safety information and instructions for the future.
The term “power tool” used in the safety instructions refers to mains-operated
power tools (with mains lead) and battery-operated power tools (without mains
lead).
It is only possible to work with the device safely if you read the operating
instructions and the safety instructions in full and strictly follow the
instructions.
The machine may only be used by persons familiar with the operating
instructions and the applicable regulations regarding occupational safety and
accident prevention.
****In addition, the “General Safety Instructions” enclosed must be followed.
- Do not operate the device in an environment with a potentially explosive atmosphere. Do not mix any highly flammable solvents or solvent-containing sub-stances with a flash point below 21 C.
- Ensure that no liquid sprays onto the motor housing and also avoid exposure to the rain – risk of electric shock!
- Do not clean the device with water – risk of electric shock!
- Always hold the device with both hands when working and ensure you have a secure footing.
- Prior to commissioning, check that the mixing stick is seated firmly and that it runs perfectly true.
- Only start/stop the device in the mixing vessel. Ensure that the mixing vessel has a firm and secure footing.
- Do not reach with your hand or objects into the mixing vessel during ongoing mixing operation. Risk of crushing!
- Wait, until the device and/or tool comes to a complete standstill. Rotating tools can get stuck and cause inju- ries or damage.
- If the sound pressure level in the workplace exceeds 85 dB (A), wear hearing protectors!
- It is recommended to wear work gloves and protective goggles when working with the mixer. Wearing close-fitting clothing is a requirement.
- Wearing a dust mask is recommended to protect against potentially harmful dust during mixing. Some mineral substances are carcinogenic. Use a vacuum cleaner where possible.
Special safety instructions for cordless machines:
- Protect battery packs from moisture!
- Do not expose battery packs to fire!
- Do not use defective or deformed battery packs!
- Do not open battery packs!
- Do not touch or short-circuit the battery packs’ contacts!
- A slightly acidic, flammable liquid may escape from defective Li-ion battery packs!
- If battery fluid escapes and comes into contact with the skin, rinse immediately with plenty of water. If battery fluid comes into contact with the eyes, rinse thoroughly with clean water and seek immediate medical attention!
Transporting Li-ion battery packs:
- The shipment of Li-ion battery packs is subject to hazardous goods legislation (UN 3480 and UN 3481). Clarify the currently valid regulations when sending Li-ion battery packs. Ask your transport company for information if necessary.
- Only send battery packs if the housing is undamaged and no fluid is escaping. Remove the battery pack from the machine for shipping purposes. Protect the contacts against short-circuit (e.g. insulate with adhesive tape).
- Remove the battery from the power tool before transporting, storing or performing any work on the power tool (e.g. maintenance, tool change, etc.).
Wear protective goggles and hearing protectors when working.
It is recommended to wear a dust mask during work involving large amounts of
dust.
Wear protective gloves when working.
Assembly HEXAFIX / paddle
Screw the HEXAFIX coupling enclosed with the packaging onto the agitator
shaft’s 5/8” external thread.
Insert the mixer with the HEXAFIX holder shaft into the coupling until it
snaps into place.
To remove or change the mixer, just pull the sleeve on the coupling and the
mixer will be released.
Keep the HEXAFIX coupling clean and grease it from time to time. This
maintains its functionality.
Operation
Always hold the machine with two hands.
Switching on
Press the button for the switch-on lock (1). The switch is unlocked.
Press the ON / OFF button (2).
The more firmly the ON / OFF switch is pressed, the faster the machine runs.
The ON / OFF switch cannot be locked!
It is best to work with the ON / OFF switch fully depressed at all times.
Switching off
Release the ON / OFF switch to finish the work.
This machine has a 2-speed gearbox.
Two maximum speeds (1st gear low speed, high torque / 2nd gear high speed) are
available.
Turn the gear selector by 180° to change from one gear to another.
Only operate the gear selector when the device is stopped.
Prevent accidental start-up: always switch the machine off if the bat- tery
pack is removed from the machine.
Work at a reduced speed when immersing the machine into or removing it from
the mix. Once the machine has been fully immersed, increase the speed to the
maximum so that sufficient motor cooling is guaranteed.
Guide the machine through the mixing vessel during the mixing process. Mix
until all the mix has been completely worked through.
Observe the material manufacturer’s processing instructions.
The tougher the mixture, the higher the torque forces acting on the machine;
prepare yourself for this during work.
Recoil may occur if the running mixer comes into contact with a surface (e.g.
base of the bucket).
Battery pack
Charge the battery pack before use. Recharge the battery pack if the
performance drops.
The ideal storage temperature is between 10°C and 30°C.
If the battery capacity has been depleted, the machine remains at a
standstill.
Re-insert a fully charged battery. “Li-Power” Li-ion battery packs have a
capacity and signal indicator (11): Press the button (10) and the charge
status is indicated using the LED lights.
If an LED light flashes, the battery pack is almost flat and must be
recharged.
Removing/inserting the battery pack Removing:
Press the button for the battery pack unlocking mechanism (3) and pull the
battery pack (6) forwards and out.
Inserting: Slide the battery pack (6) on until it snaps into place.
Fault:
Overload protection: The machine was switched off automatically. The device is
too hot!
Leave the machine idling until it has cooled down.
Care and maintenance
Remove the battery from the power tool before transporting, storing, or
performing any work on the power tool (e.g. maintenance, tool change, etc.).
There is a risk of injury if the ON/OFF switch is pressed accidentally.
Clean the machine and paddle immediately after use.
We recommend the Collomix MIXER-CLEAN cleaning bucket to clean the paddle.
Remove the paddle from the coupling after finishing the work.
Keep the HEXAFIX coupling clean and running well.
Regularly lubricate the hexagonal support of the coupling with a suitable
lubricant.
The ventilation openings must be kept clean and clear to
Disposal
The device, accessories and packaging should be introduced into an
environmentally friendly recycling system.
For EU countries only:
Do not dispose of power tools together with household waste.
According to EU Directive, 2002/96/EC on waste, electrical and electronic
equipment, and your country’s transposition into national law, power tools
that are no longer usable must be collected and sent to an eco-friendly
recycling facility.
Special instructions for cordless machines:
Battery packs must not be disposed of together with household waste! Return
defective or used battery packs to your dealer!
Do not throw battery packs into the water!
Discharge the battery pack in the power tool before disposal. Protect the
contacts against short-circuit (e.g. insulate them with adhesive tape).
Warranty
The manufacturer offers a product warranty within the scope of the delivery
terms and in accordance with legal/ country-specific regulations. Please
include your payment receipt or delivery note with any warranty claims.
Please return the device to us if you detect any irregularities.
Complaints/claims can only be considered if the device is delivered to the
Collomix Service department in a complete and undismantled state.
Any damage resulting from normal wear, overload, improper handling, non-
approved accessories, or insufficient maintenance shall be exempt from the
warranty.
Any repairs carried out by third parties shall release us from any warranty
obligation.
Any structural or functional changes to the device not authorized by us shall
result in the invalidation of the warranty as well as the declaration of
conformity.
Noise/vibration values
Measured values determined according to EN 60745 The A-weighted noise level of the device is typical:
| Sound pressure
LPA [dB(A)]| Sound power
LwA [dB(A)]
---|---|---
Xo 20 NC| 76 dB(a)| 87 dB(A)
| Uncertainty K = 3 dB
Vibration total value (when stirring mineral substances
| Emission value an [m/s2]
---|---
Xo 20 NC| 1.5 m/s2
| Uncertainty K = 1.5 m/s2
The stated technical data is subject to tolerances (corresponding to the
respective valid standards).
Emission values These values make it possible to estimate the emissions of the
power tool and compare various power tools.
The actual load may be higher or lower depending on the operating conditions
and the condition of the power tool or the attachments.
For estimation purposes, take into account work breaks and phases with lower
loads.
Define protective measures for the user, e.g. organizational measures, based
on correspondingly adjusted estimated values.
Subject to change
Manufacturer:
Collomix GmbH
Daimlerstraße 9
85080 Gaimersheim
Germany
www.collomix.com
EU Declaration of Conformity
We declare under our sole responsibility that the stated product ① complies with all applicable provisions of the directives and regulations ② listed below and are in conformity with the following standards ③. Technical file at ④
Hersteller:
Collomix GmbH
Daimlerstraße 9
85080 Gaimersheim
Deutschland
www.collomix.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>