VISUAL COMFORT KW5625BZ-ALB Signature Collection Pedra 56 Linear Chandelier Instruction Manual

VISUAL COMFORT KW5625BZ-ALB Signature Collection Pedra 56 Linear

Chandelier

Specifications

• Product Name: Pedra 56 Linear Chandelier
• Model Number: KW5625
• Installation Type: Canopy Mounted Driver
• Tools Required (Not Included): Phillips Screwdriver, Slotted Screwdriver, Slip Joint Pliers, Measuring Tape, Wire Strippers, Chain Pliers, Wire Cutters

Product Usage Instructions

Step 1: Unboxing and Preparation

1. Remove all parts from the box and place them on a clean, soft surface.

Step 2: Mounting and Installation

1. Remove tall mounting plate (B) from driver housing (F) and canopy (G) by removing collar ring (H).
2. Install a tall mounting plate (B) to the junction box and secure it with mounting screws (D).
3. Attach driver housing (F) and canopy (G) to the tall mounting plate (B) and secure with a collar ring (H).
4. Determine the desired overall length and required amount of chain (I). Shorten the chain using chain pliers.

Step 3: Electrical Connections

1. 1. Twist all fixture wires together and slip them through the mounting plate (B).

2. Connect the driver’s output neutral wire (black) to the fixture’s neutral wire (marked -) using a wire nut (A).

3. Connect the driver’s output hot wire (red) to the fixture’s hot wire (marked +) using a wire nut (A).

4. Wrap the supply ground wire (green) around the green grounding screw.

Frequently Asked Questions:

Q: What tools are required for the installation?

A: The tools required for installation include a Phillips screwdriver, slotted screwdriver, slip joint pliers, measuring tape, wire strippers, chain pliers, and wire cutters.

Q: How should I determine the length of the chain needed for installation?

A: To determine the length of the chain required, measure the desired overall length and adjust accordingly using chain pliers.
It’s recommended to keep some extra chains for flexibility during installation.

ASSEMBLY INSTRUCTIONS

Option 1: Canopy Mounted Driver

NOTICE:

• This light fixture should be installed under all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved.
• Inspect items and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Slotted Screwdriver
• Chain Pliers
• Slip Joint Pliers
• Measuring Tape
• Wire Cutters
• Wire Strippers

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove tall mounting plate (B) from driver housing (F) and canopy (G) by removing collar ring (H).

3. Install a tall mounting plate (B) to the junction box and secure with mounting screws (D).

4. Install driver housing (F) and canopy (G) to tall mounting plate (B) and secure with collar ring (H).

5. Determine the desired overall length, and amount of chain (I) needed Shorten the chain using chain pliers. (Keep extra chain)

6. Feed fixture wire through threaded rod (L), tube (K), fixture loop (J), then install threaded rod (L) & tube (K) to fixture (N) and secure using fixture loop (J).

7. Attach chain (I) to collar loop and to fixture loop (J) using quick links (E). Secure quick links (E).

8. Thread fixture wire through the chain (I).
   NOTE: When you reach the tall mounting plate (B), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

9. Separate two sides of molded wire, and strip insulation on each 5/8″.

10. Loosen collar ring (H) and let driver housing (F) and canopy (G) slip down chain (I) carefully.

    • NOTICE:
    • This light fixture should be installed under all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved.
    • Inspect items and contents carefully. If any damage or defect is found, do not install it.
    • Retain all packaging material until installation is complete and approved.

11. Twist all fixture wires together and slip through mounting plate (B). NOTE: Untwist wires and separate them to prepare for connection.

12. Connect driver (C) output neutral wire (black) to the fixture neutral wire (marked “-”) using wire nut (A).

13. Connect driver (C) output hot wire (red) to the fixture hot wire (marked “+”) using wire nut (A).

    • CAUTION: Do not reverse the hot and neutral connections.

14. Wrap supply ground wire (green) around the green grounding screw (see diagram 1). Tighten.

    • NOTE: The fixture must be grounded.

15. Connect driver (C) neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).

16. Connect driver (C) hot wire (black) to the supply hot wire (usually black) using wire nut (A).

    • CAUTION: Do not reverse the hot and neutral connections.

17. Make sure all wire connections are tight, then carefully tuck into the junction box.

18. Insert driver (C) into the mounting plate (B) bracket.

19. Install driver housing (F), and canopy (G) to mounting plate (B) and secure with collar ring (H).

20. Thread alabaster shades (M) to fixture (N).

    • Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Option 2: Ceiling Mounted Driver

NOTICE:

• This light fixture should be installed under all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully.
• If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Slotted Screwdriver
• Chain Pliers
• Slip Joint Pliers
• Measuring Tape
• Wire Cutters
• Wire Strippers

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Place driver (C) into the ceiling and route all wires through one of the knockouts in the junction box.
3. Remove the tall mounting plate (B) from driver housing (F) and canopy (G) by removing the collar ring (H).
   • NOTE: Driver housing (F) will not be used for ceiling-mounted assembly. Keep part and store for future use.
4. Install a short mounting plate (O) to the junction box and secure it with mounting screws (D).
5. Secure the collar loop (P) to the short mounting plate (O) using pliers to tighten the locknut.
6. Install canopy (G) to short mounting plate (O) and secure with collar ring (H).
7. Determine the desired overall length, and amount of chain (I) needed Shorten the chain using chain pliers. (Keep extra chain)
8. Feed fixture wire through threaded rod (L), tube (K), and fixture loop (J), then install threaded rod (L) & tube (K) to fixture (N) and secure using fixture loop (J).
9. Attach chain (I) to collar loop (P) and fixture loop (J) using quick links (E). Secure quick links (E).
   • NOTICE:
   • This light fixture should be installed under all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved.
   • Inspect items and contents carefully.
   • If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.
10. Thread fixture wire and ground wire through the chain (I).
    • NOTE: When you reach mounting plate (O), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.
11. Separate two sides of molded wire, and strip insulation on each 5/8″.
12. Loosen collar ring (H) and canopy (G) and slip down chain (I) carefully.
13. Twist all fixture wires together and slip through the mounting plate (O).
    • NOTE: Untwist wires and separate them to prepare for connection.
14. Connect driver (C) output neutral wire (black) to the fixture neutral wire (marked “-”) using wire nut (A).
15. Connect driver (C) output hot wire (red) to the fixture hot wire (marked “+”) using wire nut (A).
    • CAUTION: Do not reverse the hot and neutral connections.
16. Wrap supply ground wire (green) around the green grounding screw (see diagram 1). Tighten.
    • NOTE: The fixture must be grounded.
17. Connect driver (C) neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
18. Connect driver (C) hot wire (black) to the supply hot wire (usually black) using wire nut (A).
    • CAUTION: Do not reverse the hot and neutral connections.
19. Make sure all wire connections are tight, then carefully tuck into the junction box.
20. Install canopy (G) to mounting plate (O) and secure with collar ring (H).
21. Thread alabaster shades (M) to fixture (N).

Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>