Eonon P4 9.33 inch Dash Windshield Mounted CarPlay User Manual

User Manualhttps://www.eononsupport.com/q/1005.html

Precautions

Please read the user manual and follow all safety rules  and operating instructions. Keep the manual in a safe place for future reference, along with the warranty card.

1. Please power on the device and confirm that all functions are working properly before installation. During installation, do not forcefully pull or twist the wires, and ensure that all wires are connected properly. Do not modify the original cables. If any cables are damaged, be sure to replace them with a new cable before powering on the device.
2. If the unit works properly before installation but issues occur after installation, check for poor connections or short circuits caused by pin displacement in the connectors.
3.  Use this unit in DC7-32V vehicles only to prevent product damage or fires.
4.  Keep the unit away from liquids. If you notice water, foreign objects, unusual odors, or screen abnormalities, power off the unit immediately and contact your dealer or Eonon customer service. Avoid using it in this condition to prevent fire, electric shock, or failures.
5.  Do not use this unit for a long time after the engine is turned off, or it will drain the battery power.
6. Do not remove the MicroSD card while recording is in progress.
7.  Do not disassemble or modify the unit on your own without professional expertise. Please consult your dealer or Eonon customer service if you have any questions on installing or using this product.
8. Please use this product in accordance with traffic laws.
9. We reserve the right of final explanation.

Product Overview

1. Ambient light sensor
2. Built-in microphone
3.  Reset
4.  Front camera
5.  Type-C power input
6. Backup camera input
7. MicroSD card slot
8.  AUX output
9. Press to turn on/off the display, long press to power on/off.

Accessories

Installation Instructions

Car Stereo
A. To install the unit on the center console:

1. Clean the area on the center console where you want to installthe unit.
   

2. Attach the mounting bracket to the unit.
   

3. Remove the sticker from the bottom of the mounting bracket. Place the bracket onto the center console and press it firmly.
   

4. Connect one end of the cigarette lighter power cable to the power in port on the unit, and the other end to the car cigarette lighter socket.
   

B. To install the unit to the windshield:

1. Clean the area on the windshield where you want to install the unit. Change the mounting base to suction cup holder.
   

2. Remove the sticker from the suction cup holder.
   

3. Attach the holder to the windshield and press it firmly. Close the lever to lock into place.
   

4.  Connect one end of the cigarette lighter power cable to the power in port on the unit, and the other end to the car cigarette lighter socket.
   

5. Adjust the unit to the desired angle and installation completed.

Connection Instructions
Connect the Type-C interface of the cigarette lighter power to the unit’s POWER-IN port, and plug the other end into the car’s cigarette lighter power port.

Backup Camera

1. Connect the red trigger wire from the backup camera to the positive terminal of the car reverse light.
2. Connect the plug of the camera into the AV in port on the head unit.
   

Phone Link & DVR

Apple CarPlay/Android Auto
Apple Airplay/Android Cast
Please refer to the connection steps in the corresponding app for the setup.

DVR

1. To enable the DVR function, please insert
   a Micro SD card into the Micro SD card slot.

2.  Adjust the positions of the front and rear cameras.

Audio Output

Tap   .
Speaker: Sound is output through the built-in speaker of the unit.

BT Audio: Only available when using CarPlay or Android Auto.

1. After connecting CarPlay or Android Auto, find Bluetooth of your factory car radio on your phone and connect to it.
2. Set your factory car radio to Bluetooth music mode.

FM Output

1. Choose a transmission frequency that is not occupied by a radio station to prevent interference. If there is interference or noise, please switch to another frequency.
2. Tune your factory car radio to the corresponding frequency.

AUX Output

1. Connect the AUX output of the unit to the AUX input of your factory car radio via an AUX cable.
2. Set your factory car radio to AUX mode.

Specifications

should be Class 10 or higher.

FAQ

.” image-1=”” headline-2=”p” question-2=”Images do not automatically change while reversing” answer-2=”Please connect the red trigger wire from the backup camera to the positive terminal of the car reverse light.” image-2=”” headline-3=”p” question-3=”Android Auto is not working” answer-3=”1. This unit only supports wireless Android Auto. Please be sure that your phone supports wireless Android Auto. Please note that some mobile phones only support wired Android Auto instead of wireless Android Auto. 2. Please install the Android Auto app from the Google Play Store app on your phone and enable the Wireless Android Auto option. 3. To use wireless Android Auto, please turn on WiFi and Bluetooth of your phone and connect your phone’s Bluetooth to the head unit’s Bluetooth. Please note that you only need to connect Bluetooth but not WiFi.” image-3=”” headline-4=”p” question-4=”CarPlay is not working” answer-4=”This unit only supports wireless CarPlay. To use wireless CarPlay, please turn on WiFi and Bluetooth of your iPhone and connect your phone’s Bluetooth to the head unit’s Bluetooth. Please note that you only need to connect Bluetooth but not WiFi.” image-4=”” headline-5=”p” question-5=”DVR is not recording” answer-5=”1. Check if the MicroSD card is inserted properly. 2. Ensure the MicroSD card is class 10 or higher. 3. Format the MicroSD card and try again. 4. Check if the MicroSD is damaged. If it is damaged, replace it with a new one and try again.” image-5=”” count=”6″ html=”true” css_class=””]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>