JIAABCHOMO LK-9300 9D Head Shaver Replacement Blades User Manual

**JIAABCHOMO LK-9300 9D Head Shaver Replacement Blades User Manual

**

Product brief introduction

(a) Shaver
(b) Charger
(c) Comb
(d) Precision trimmer
(e) Nose hair trimmer cover
(f) Nose &ear trimmer
(g) Soft face sponge
(h) Facial cleaning brush
(i) Brush
(j) Horing mes

Notes
Before using the product, please read carefully the operating instructions and keep properly for future reference.

1. Only the included charger can be used.

2. Please use the adapter below 5V 1A for charging, do not use theadapter above 5V 1A for charging.

3. The charger includes a transformer which should not be cut off and replaced with another plug; otherwise, it will lead to serious results.

4. If the charger is damaged, it should be replaced with a new one with the original type to avoid danger.

5. The three blade is made of super thin alloy. To avoid of breakage. please do no press it by hand (Fig 1).
   

6. The temperature for the product’s charger and storage should not exceed 5℃-35℃.

7. Make sure the charger can not be rinsed under **watel(Fig 2).

**

8. Unplug the charger before cleaning the shaverwith running water.(Fig 3).
   

9. The waterproof grade IPX4.

10. This product cannot be used by physically distempered, s ensorially or mentally disordered, or inexperienced persons (including children), unless they are under supervision or instruction by people in charge of their security.

11. Take care of children to keep them away from this product

12. Pls clean inside beard if the shaver can not work after you pressthe switch.

13. It’s necessary to ensure to put the protective coveron the shaver when you travel to protect the shaver head.

Charge

Make sure the product is power-off before the charge.Fast charge for 2 hours, Keep use about 90 minutes after full charge. **(Fig4)

**

lt’s better for the product not to be connected to thepower supply for more than 24 hours.

1. Insert the product charger into the shaver (Fig 5)
   

2. Plug in the charger .

3. The charge indicator lights up (Fig 6).
   

4. After the full charge, unplug the charger and also pull out the product’s plug from the shaver.

5. lt can charge with the charging base.

How to Use Product

Shaving

1. Press the button ON/OFF to start the shaver.
2. Make the shaver head part move quickly on the skin instraight lines and circles **(Fig 7).

**

To ensure a better shaving effect, the shaver must be cleaned regularly.The easiest and most sanitary way to clean the product is to wash the shaver head part andthe whisker storeroom with water each time after using it.

1. Stop the shaver (Fig 8).
   

2. Pull away the shaver heads on the side one by oneand then rotate and pull out the middle head in the arrow direction indicated on it.

3. Clean the shaver head part and the hair storeroom for some time with running water (Fig 9).
   
   Make sure the inside of both the shaver head part andthe hair storeroom has been cleaned thoroughly.

4. Wash the product’s surface **(Fig 10).

** Close the shaver head part and throw off surplus water.
Do not wipe the shaver head part with a towel or paper tissues, which may cause damages to the shaver head

5. Open the shaver head part again and remain so todry up the product (Fig 11 ).You can also use the brush included to clean the hair storeroom.

Change
Change the shaver head once a year to get the best shaving effect. The shaver has a long service life if not damaged for human factors.The damaged shaver head can only be replaced with shaver head of this company.

1. Pull out the old shaver head assembly out of theshaver (Drawing )(Fig 12)
   
   

2. Insert the new shaver head assembly into the groove (1) on the shaver’s top and then press down the shaver head assembly (2) to mount it on the shaver (a click will be heard) (Fig 13 ).
   
   

PRECISION TRIMMER Instruction

Turn off the shaver power, remove the shaver head insert the hair clipper into the slot of the top shaver. Then press down the hair clipper head parts to installed in the shaver body.(hear the sound like”kaca”) (Fig 14).

TRIMMER

Note: Make sure your hair is clean and dry. Do not use the product for wet hair.

1. Take note that comb your hair according hair growth direction before clip hair.

2. Put on the comb accessories to the slot both sides,the sound like “kaca”,make sure the comb accessories have already fix on slot both sides intrue ways (Fig 15).
   

3. The comb accessories have two length“3MM“”5MM”and “7MM” for clip hair with different length.Replacing the comb accessories direction according to length mark in the bottom (Fig 16 ).
   
   Put down the comb accessories from one sides lot toanother (Fig17).

4. Open the switch, use it above hair slowly. For good clip effect, please use the product in the differenct direction from hair growth direction.
   

Cleanness /Lubricate

1. Take out the precision trimmer head, use brush toclean the trimmer or clipper, or wash the trimmer head.
2. Do not use abrasive,alcohol,gasoline or acetoneetc. liquid to wash the product.
3. You should clean the product immediately after using once.
4. For best using and clip effect,please add somelubricating oil every three monthes.
   The Lubricate oil is not included in this package you need to purchase it by yourself.

Nose trimmer instruction
Turn off the shaver power, remove the shaver head,insert the nose trimmer into the slot of the top shaver.Then press down the nose trimmer head parts to installed in the shaver body.(hear the sound like “kaca”) (Fig 18)

Trim nose hair

1. Make sure your nose is clean.
2. Open the switch, put the nose trimmer towards your inside nose,turn the nose trimmer to clip your long nose hair (Fig 19)
   
   

Do not exceed 0.5cm for nose trimmer length inside your nose.
To reduce itch, you should put one side of the nose trimmer tip close your skin.

Clip ear hair

1. Clean outside ear,make sure no earwax.
2. Open the switch, then turn the trimmer tip towards your ear to clipyour long ear hair.
3. Put the trimmer tip towards your outside earlap slowly. (Fig 20)
   
   Do not exceed 0.5cm for trimmer tip length inside your ear

SOFT FACE SPONGE

With cleansing brush, can wash your face softly and clean

Using the cleansing brush attachment

Use the rotating brush attachment with your daily cleansing cream.The cleansing brush attachment removes oil and dirt,contributing to a healthy and oil-free skin.

1. Make sure the appliance is switched off and attachthe cleansing brush attachment to the appliance.( Fig 21)
   
   

2. Moisten the attachment with water.Do not use theappliance with a dry brush head, as this can irritatethe skin.
   Note : soft face sponge and facial Cleansing brush are using same base (Fig 22-1-2)
   
   
   Tip: Use the attachment before shaving for easiershaving and a more hygienic shaving result.

3. Moisten your face with water and apply a cleanser to your face.

4. Place the attachment on your right cheek.

5. Switch on the appliance.

6. Gently move the attachment across your skin from the nose towards the ear. Do not push the attachment too hard onto the skin to make sure the treatment too hard onto the skin to make sure the treatment remains comfortable.

7. After approx.20 seconds you can move the attachment to your left cheek and start cleansing this part of your face.
   Caution: Do not clean the sensitive area around your eyes.

8. After approx. 20 seconds you can move the attachment to your forehead and start cleansing this part of your face.Gently move the attachment from left to right.
   Note: We advise you not overdo the cleansing and not cleanse any area longer than 20 seconds.

9. After the treatment, rinse and dry your face. Your face is now ready for the next step of your daily skincare routine.

10. Clean the attachment after use (see chapter Cleaning and maintenance).

11. You can use the appliance to trim edge or shave facial hair (beard, moustache and sideburns).

12. Shave for a smooth result, trim to obtain a certain length and edge to create perfect edges and sharp lines. This appliance is not intended for shaving.edging or trimming hairs on lower body parts orscalp hair. Take your time when you first start to use the appliance. You have to acquire practice with the appliance (Fig 23 ).
    
    

Accessories

The following accessories are included with the product: Charger; Brush;

Environmental Protection

1. To discard the product, please don’t put it together with general domestic rubbish heaps but hand it to the officially designated recycle center for the environmental protection (Fig 24)
   
   

2. The built-in rechargeable battery contains substances which may pollute the environment, so it must be unloaded from the product or sent to the officially designated recycle center to be disposed before it is discarded.

The battery should not be unloaded unless it has been used up.

1. Unplug the charger and also pull out the product’s plug from the shaver.
2. Unload the battery.
   Do not plug in the shaver again after unloading the battery.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>