CANOPIA 11×17.2 Yukon Garage Shed Kit User Guide

11×17.2 Yukon Garage Shed Kit
User Guide

HOW TO ASSEMBLE YUKON™ SERIES
11×17 / 3.3×5.2 | 11×21 / 3.3×6.4
IMPORTANT!
Please read these instructions carefully before starting assembly. Keep these instructions in a safe place for future reference.

AVAILABLE MODELS

11×9 / 3.3×2.7

PRIMARY UNIT 11×9 / 3.3×2.7| 2 BOXES

11×13 / 3.3×3.4

PRIMARY UNIT 11×9 / 3.3×2.7| 2 BOXES
1 EXTENSION UNIT 11×4 / 3.3×0.4| 1 BOX
11×17 / 3.3×5.2

PRIMARY UNIT 11×9 / 3.3×2.7| 2 BOXES
2 EXTENSION UNITS 11×4 / 3.3×0.4| 2 BOXES
REINFORCEMENT KIT 3 pcs| 1 BOX
11×21 / 3.3×6.4

PRIMARY UNIT 11×9 / 3.3×2.7| 2 BOXES
3 EXTENSION UNITS 11×4 / 3.3×0.4| 3 BOXES
REINFORCEMENT KIT 4 pcs| 1 BOX
Yukon WPC floor KIT – purchased separately

FLOOR KIT 11×9 / 3.3×2.7| 2 BOXES
| FLOOR KIT 11×13 / 3.3×3.4| 3 BOXES| FLOOR KIT 11×17 / 3.3×5.2| 4 BOXES| FLOOR KIT 11×21 / 3.3×6.4| 5 BOXES

HAVE A CONCERN? WE CAN HELP.
Before returning your purchase:
Please take a look at our “How to Assemble” video guide. Scan the QR Code below or go to canopia.shop/Assemle-Yukon 

canopia.shop/Assemle-Yukon

You didn’t find what you were looking for?
We can help at canopia.shop/support

https://canopia.shop/support

Still can’t find what you are looking for?
Please see next page for local customer care.

WE ARE HERE TO HELP
canopia.com/contact-us

https://canopia.shop/contact_us

CR • SL
0599-37-057 | info@ms-viscom.com
DK
07-575 42 70 | post@nshnordic.com
CH • HU • SK
0493-523-523 | servis@garland.cz
PL
Infolinia: 801-011-929 | 22-349-93-36 kontakt@ogrodosfera.pl
FI
Novotna: 09-6866720 Taki | Arabsat: 050-3715350 www.horisontenterprises.fi | tuki@horisontenterprises.fi
CY
0224-971-13 | alpaco@alpacodomica.com www.alpacodomica.com
BASE DIMENSIONS YUKON

11021/3.386.4
WIDTH| A| 307 cm/ 121
LENGTH| B| 508 cm/200
633 cm/ 249°

TOOLS G EQUIPMENT

| 2 people needed
---|---
Wrench 10 mm 113/32″
Soap
| Work gloves
---|---
Tape Measure
Ladder
| Philips head Screwdriver
---|---
Cordless drill Phillips head
Cordless drill With Drill Bit
| Silicone
---|---
Scissors
Jigsaw (WPC Floor Kit)

SITE PREPARATION & FOUNDATION

A-PREPARE THE SITE
The product must be positioned and fixed on a flat level surface

1. Clear the site
2. Level the ground

­B. CHOOSE YOUR FOUNDATION TYDE
For a foundation, we recommend using tree material types Corrected /Deque treated wood/wood deer peer blocks
Solid base Not possible * The size of the product displayed is for illustration purposes only and may not reflect the size of your product.
C- ANCHOR TO FOUNDATION

• Ona solid base

Secure the product to the foundation of your choice using suitable screws 6plug or ma600ry a0ch0r$ [not suppled)
Make sure you have at least5am/2 between the product bare ad th edges of our foundation on all sides
D-OPTIONELE ACCESOIRES

1. WPC FLOOR KM If you’ve purchased the WPC Floor Kit with the product, relevant steps are marked with these icons. If you’ve assembled the product without the floor kit and wish to add one, please refer to the relevant steps (marked with these icons) in the assembly and perform the necessary adjustments.

2. UTILITY SHED SHELF KIT:
   If you’ve purchased shelf kits, it is recommended to insert screws #411 inside the profiles’ tracks during the walls’ assembly.

3. VERTICAL BICYCLE HANGER:
   Can be installed once the product is fully assembled. Make sure the bottom wheel is at floor level.

INFORMATION

SAFETY ADVICE

• It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
• Always wear work gloves during panel sliding.
• Always wear shoes and safety goggles when working with extruded aluminum.
• IF using a step laddercr power tools make sure that you follow the manufacturer’s safety advice.
• Do not touch overhead power cables with the aluminums profiles.
• Do not attempt to assemble the product in windy or wet conditions.
• Dispose of all plastic bags. Keep them out of reach of small children.
• Keep children away from the assembly area.
• Do not lean against or push the products during construction.
• Do not position your product in an area exposed to excessive winds.
• Do nit attempts assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
• Hot items such as recently used grills, blowtorches etc. must nit be stored in the product.
• Make sure there are no hidden pipes or cables in the ground before anchoring to foundation.
• This predict is designed to be used mainly as a garden shed.
• To prevent water from seeping through the floor, the product must be mounted on a raised surface from the ground.
• Make sure to anchor the product directly to a solid foundation to increase the product’s stability and wind resistance in areas with severe weather conditions. Make sure that there are no obstructions between the assembly area and the final position of the product. The Palram – Canopia Anchoring kit is available for purchase separately.

CARE & MAINTENANCE 

• When your product needs to be cleaned, use a soft doth and rinse with cold clean water.
• DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
• Clean the product once assembly is complete.

BEFORE ASSEMBLY

• Selecting a site:
•  Choose your site carefully before beginning assembly.
• Choose a sunny position away from overhanging trees.
•  The product must be positioned and fixed on a flat level surface.
• The product must be secured directly to a solid foundation.
• This is a multi-part assembly best achieved by two pecple. Allow at least half a day for the assembly process.
• Take all components & parts out of the packages. Sort the parts and check against the content parts list.
• Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
• Please note multi-sided profiles are used in this product. As a result some holes in the profiles are not used during assembly.
• Please review entire instructions before starting. Carry out the assembly steps in exact order.
• Please consult your local authorities if any permits are required prior to constructing the product.
• Please ensure you have sufficient side space for inserting the roof panels during the assembly process.

IMPORTANT!

• Firmly connect the product to a level surface immediately after completion of the assembly.
• Anchoring this product to the ground is essential to its stability and rigidity. It is required to complete this stage in order for your warranty to be valid.
• During assembly use a soft surface below the parts to avoid scratches and damages.
• We recommend checking for restrictions or covenants for building this product in your area. In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product.

DURING ASSEMBLY

During assembly, you will encounter different icons for different products. Please see below for more information:

| You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.
---|---
| Use a rubber mallet if necessary.
| Make sure you remove covering plastic film from both sides of the panel.
| All panels with the stamped words “THIS SIDE OUT” must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place.
| This icon indicates that the installer should be inside the product.
| This icon indicates that the installer should be outside the product.
| Steps marked with dashed outlines refer to Extensions only. Some of the steps are irrelevant for an assembly of a single product when assembling a single or an extended product, some parts may be surplus.
| These 2 icons below indicate if screw’s tightening is required or not. Temporary tightening of a few screws may be needed to prevent a profile from sliding out Tighten all screws once assembly is completed

IMPORTANT!.
The drawings in this manual are designed for products 11×17 / 3.3×5.2 & 11×21 / 3.3×6.4.

IMPORTANT ASSEMBLY STEPS

When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments

Step 1: If you’ve purchased a WPC Floor Kit, do not assemble profile #8851!
Step 8: if you’re installing a WPC Floor Kit, measure and cut floor board # 8912.
Step 18: Matte side of all product’s panels should be facing out!
Use mild soap if needed to ease sliding of profiles & panels.
Step 22: It is recommended to insert screws #8192 as preparation for mounting shelves.
If you’ve purchased a Utility Shed Shelf kit, mount a maximum of 2 shelves per post.
Step 26: Note the bracket’s direction as shown in the drawings, make sure the bracket is in line with the gutter profile.
Step 27: Note the bracket’s direction and make sure the screws are positioned inside the profile’s channels as shown in the drawings.
Step 28: It is recommended to insert screws #8192 as preparation for mounting shelves. If you’ve purchased a Utility Shed Shelf kit, mount a maximum of 2 shelves per past.
Step 32: If you’ve purchased the Yukon 11×21 / 3.3×6.4 Storage Shed, please continue building the walls, adding the additional bracket and inserting screws #8192 as preparation for mounting shelves, as you’ve done in the last 4 steps.
Step 33: It is recommended to insert screws #8192 as preparation for mounting shelves. If you’ve purchased a Utility Shed Shelf kit, mount a maximum of 2 shelves per post.
Step 41: Before inserting the screws, make sure the internal metal profiles are not protruding and are well connected with one another inside the aluminum profiles.
Step 44: — The sticker must be placed on a clean and dry surface. Step 53: Slow down and be careful when sliding the panels in.
Step 56: Make sure the distance between the wall’s aluminum profiles and gutter is identical prior ta tightening the screws on the inside.
Step 73: Make sure the shed is leveled prior to anchoring it to the surface of your choosing. Use suitable screws and plugs (not supplied).
Contents![CANOPIA 11x17.2 Yukon Garage Shed Kit

• contents 2](https://manuals.plus/wp-content/uploads/2023/10/CANOPIA-11x17.2 -Yukon-Garage-Shed-Kit-contents-2.png) Extension Kit

|
---|---
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|

15 YEAR LIMITED WARRANTY

PALRAM – CANOPIA | 15 YEAR LIMITED WARRANTY

PARAM Canopied Ltd. (Company number: 512106824) whose registered office is at Tetradifon Industrial Park, M.P Misgave 2017400, Israel (“Canopied”) warrants that the product will be free from defects in material or workmanship for a percid of 15 years from the original date of purchase. » This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopies’ written specifications. + This warranty does not cover defects  resulting farm normal wear and tear including, but not limited to: damage caused by use of farce, incorrect handling, inappropriate use, negligence, accidents, impact from foreign abject, vandalism, pollutants, alteration, painting,  image resulting from cleaning with incompatible detergents or minor deviations of the product. » This warranty does not apply to damage resulting from “acts of Nature’, which includes but is not limited to hail, storm, tornado, hurricane, blizzard, flood, crfire. » Upon submitting proof of purchase and evidence of the claimed product failure, and subject to reporting the failure in writing within 30 days after discovery of the defect. Canopied, at its sole discretion, will replace defective parts of the Product. or refund you a prorated portion of the purchase price on a straight-line depreciated basis for the length of the warranty.

www.canopia.com

References

• Contact Us Archive - Canopia
• Inspection Systems for the Electronics Industry – Viscom – Viscom
• Αρχική Σελίδα - Alpaco Domica
• Canopia United Kingdom - Celebrate Outdoor Living

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>