Zler HFK9219-1 Heavy Duty Rollator Walker User Manual

Zler HFK9219-1 Heavy Duty Rollator Walker

Product Information

Specifications:

• Model: HFK9219-1
• Product Type: Rollator
• Components: Right handle, Left handle, Right rear leg tube, Left rear leg tube, Left front wheel, Right front wheel, Mainframe, Backrest
• Storage Temperature: -10°C to 40°C
• Relative Humidity: Up to 80%

Product Usage Instructions

Preparation before Assembly:

1. Unpack the product carefully and remove plastic ties and bubble bags using scissors.
2. Protect the parts by laying paper or carpet on the ground to prevent scratches.
3. Differentiate the parts and components using the product structure diagram.
4. Remove the inner carton and place the parts accordingly.

Assembly Instructions:

1. Step 1: Attach the right handle and left handle to the main frame.
2. Step 2: Install the right rear leg tube and left rear leg tube on the main frame.
3. Step 3: Mount the left front wheel and right front wheel on the main frame.
4. Step 4: Attach the backrest to the main frame.

Product Maintenance:

1. Avoid scratching or scraping the product surface with hard objects to prevent material damage.
2. Clean and maintain using a neutral synthetic detergent, a damp cloth, and then a dry cloth.
3. Avoid contact with strong acids and alkalis to prevent corrosion.

Storage Conditions:
Store the rollator in a clean, well-ventilated room with a temperature range of -10°C to 40°C and relative humidity not exceeding 80%. Avoid exposure to corrosive gases, moisture, light, and heat during transportation.

Frequently Asked Questions (FAQ):

Q: How do I clean the rollator?
A: For daily cleaning, use a neutral synthetic detergent with a damp cloth followed by a dry cloth to wipe the surface.

Thank you very much for choosing our products, please read the instructions carefully before assembling

• Product: Zler Rollator
• Model: HFK9219 1

Product Structure Diagram

The product structure diagram is as follows:

1. Right handle
2. Left handle
3. Right rear leg tube
4. Left rear leg tube
5. Left front wheel
6. Right front wheel
7. Main frame
8. Backrest

Preparation before Assembly

Firstly, Preparation before assembly:
After unpacking the packing box, first use scissors to remove the plastic ties and the packed bubble bag. Please take care to protect all the parts in the box. If assembling on the ground, lay the paper on the ground first. Or carpet to prevent scratches, pay attention to distinguishing the parts and components, and then remove the inner carton to take out the parts and place them first. There are bulk accessories in the packaging box as shown in Figure 1:

1. Right, handle
2. Left handle
3. Right rear leg tube
4. Left rear leg tube
5. Left front wheel
6. Right front wheel
7. Main frame
8. Backrest

Assembly Instructions

Secondly, Assembly instructions:
(please refer to the part number and name in Figure 1 for assembly):

• Step 1: (As shown in Figure 2) Put 1 right armrest tube and 2 left armrest tubes on the 7 mainframes respectively;
• Step 2: Put 3 rear wheel tubes right and 4 rear wheel tubes left on 7 respectively.
• Step 3: On the mainframe, put 5 on the front wheel left and 6 on the front wheel right on the 7 main frame respectively;
• Step 4: Put the 8 backrest tubes on the 7 main frames.

Check After Installation

Thirdly, check after installation:

1. Whether the four-wheeler is installed correctly, please refer to the manual diagram for comparison.
2. Verify that all parts of the four-wheeler are fully assembled, and you can check for extra parts.
3. Check whether there is any looseness in the installation of the four-wheeler. If there is any looseness, tighten the screws and nuts.
4. Check the appearance of all components of the four-wheeler for skew, and make appropriate adjustments.
5. Check whether the four-wheeler brakes are normal, whether the folding is smooth, and whether the steering is smooth.

Product Maintenance

Fourth, product maintenance and maintenance methods:

1. Do not scratch or scrape the surface of the product with hard objects to prevent material damage.
2. For daily cleaning and maintenance, apply neutral synthetic detergent, wipe with a damp cloth, and then wipe with a dry cloth.
3. Do not contact with strong acids and alkalis to prevent corrosion.

Fifth, Storage conditions and methods:
After packaging, the four-wheeler should be stored at a temperature not exceeding -10 ℃ to 40 ℃, and a relative humidity not exceeding 80%. No corrosive gas and well well-ventilated, clean room. Keep away from moisture, light and heat during transportation.

Zler Brand Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>