HotelMate MC35E Semi Conductor Fridge Instruction Manual

: June 11, 2024
: HotelMate

HotelMate MC35E Semi Conductor Fridge

HotelMate MC35E Semi Conductor Fridge product

Introduction

Semi-Conductor-Fridge is a household appliance that uses a thermoelectric cooling system to keep food and drinks cool. This fridge is manufactured by PKM, a German company that specializes in producing domestic appliances.

Technical Specifications

Klimaklasse: N
Energieeffizienzklasse: E
Energieverbrauch/Jahr in kW/h: 70,00
Stromspannung/Frequenz: 220-240 VAC (50 Hz)
Inhalt brutto/netto in l: 35/32
Lautstärke: 22 dB/A
Regelbarer Thermostat: No
Kompressor: No
Kältemittel: R600a/25 g
Automatische Abtauung: Yes
Innenbeleuchtung: Yes (LED)
Anzahl der Ablageflächen: 2/2
Gewicht netto / brutto in kg: 10,25/11,60

Technical modifications reserved.

*****	According to regulation (EU) No. 2019/2016
**	On a scale from A (highest efficiency) to G (lowest efficiency).
***	Based on standard measurement results within 24 hours. The current

energy consumption depends on the way the appliance is used as well as on its site.
****| This product contains a LED light source of energy efficiency class G according to EU-Regulation 2019/2015.

Safety Instructions

Before operating the appliance, carefully read the safety instructions provided in the user manual. Ignoring the safety instructions can be dangerous and may result in serious injury or death.

DANGER! indicates a hazardous situation which, if ignored, will result in death or serious injury.
WARNING! indicates a hazardous situation which, if ignored, could result in death or serious injury.
CAUTION! indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.
NOTICE! indicates possible damage to the appliance.
Store this manual in a safe place so you can use it whenever it is needed. Strictly observe the instructions to avoid damage to persons and property.
Check the technical periphery of the appliance! Do all wires and connections to the appliance work properly? Or are they time-worn and do not match the technical requirements of the appliance? A check-up of existing and newly-made connections must be done by an authorized professional. All connections and energy-leading components (incl. wires inside a wall) must be checked by a qualified professional. All modifications to the electrical mains to enable the installation of the appliance must be performed by a qualified professional.
The appliance is intended for private use only as well as to be used (1) in staff kitchen areas of shops, offices and other working environments; (2) by clients in hotels, motels, B&B and other residential type environments; (3) for catering and similar non-retail applications.
The appliance is intended for cooling food/beverages only.
The appliance is intended for indoor-use only.
The appliance is not intended to be operated for commercial purposes, during camping and in public transport.
Operate the appliance in accordance with its intended use only.
Do not allow anybody who is not familiar with this instruction manual to operate the appliance.
This appliance may be operated by children aged from 8 years and above as well as by persons with reduced physical, sensory and mental capabilities or lack of experience and knowledge if they are supervised or have been instructed concerning the safe use of the appliance and do comprehend the hazards involved. Children must not play with the appliance. Cleaning and user- maintenance must not be carried out by children unless they are supervised.

DANGER!

Do not connect the appliance to the mains if the appliance itself or the power cord or the plug are visibly damaged.
Never try to repair the appliance yourself. If the appliance does not operate properly, please contact the shop you purchased the appliance at. Original spare parts should be used only.
When the power cord is damaged, it must be replaced by the manufacturer or an authorized aftersales service or a qualified professional only.
RISK OF ELECTRICAL SHOCK! Never touch the plug while your hands are wet.

WARNING!

This appliance is equipped with the environmental-friendly refrigerant R600a. The refrigerant R600a is inflammable. The components of the cooling circuit must neither be damaged during transport nor use.
If any part of the cooling circuit is damaged, the appliance must not stand near a fire, naked light or spark-generating devices. Contact the shop you purchased the appliance at immediately .
If gas is set free in your home:
- Open all windows.
- Do not unplug the appliance and do not use the control panel or thermostat.
- Do not touch the appliance until all the gas has gone.
- Otherwise sparks can be generated which will ignite the gas.
Keep all components of the appliance away from fire and other sources of ignition when you dispose of or decommission the appliance.
EXPLOSION HAZARD! Do not store any explosive materials or sprays, which contain flammable propellants, in your appliance. Explosive mixtures can explode there.
While unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept away from children. CHOKING HAZARD.
Do not connect the appliance to the electric supply unless all packaging and transit protectors have been removed.
Operate the appliance with 220-240 VAC (50/60Hz) only. All connections and energy-leading components must be replaced by an authorized professional.
Do not use a socket board or a multi socket when connecting the appliance to the mains.
Do not connect the appliance to an energy saving plug (e.g. Sava Plug) and to inverters which convert direct current (DC) into alternating current (AC), e.g. solar systems, power supply of ships.
A dedicated and properly grounded socket meeting the data of the plug is required to minimize any kind of hazard. The appliance must be grounded properly.
Check that the power cord is not placed under the appliance or damaged when moving the appliance.
The technical data of your energy supplier must meet the data on the model plate of the appliance.
Your domestic circuit must be equipped with an automatic circuit breaker.
Do not modify the appliance.
Turn off the power before you install the appliance and before you connect it to the mains. RISK OF FATAL ELECTRIC SHOCK!
Disconnect the appliance from the mains before you clean or maintain it.
Do not use any electric appliances inside the food storage compartments of your appliance unless they are recommended by the manufacturer of your refrigerator.
Do not put any heat-radiating appliances onto your appliance.
Do not install the appliance in a place where it may come in contact with water/rain; otherwise the insulation of the electrical system will be damaged.
Do not put a water-boiler or vases onto your appliance. The electrical components of your appliance can be seriously damaged by water over-boiling or spilled water.
Do not use any steam cleaners to clean or defrost the appliance. The steam can get into contact with the electrical parts and cause an electrical short. RISK OF ELECTRIC SHOCK!
Never use mechanic devices, knives or other sharp-edged items to remove encrusted ice inside the appliance. RISK OF ELECTRIC SHOCK caused by damaging the interior of the appliance.
Children must never play with the appliance.
If you decommission your appliance (even temporarily), ensure that children cannot get into the appliance. Strictly observe the corresponding safety instructions numbers. 1 and 4, chapter DECOMMISSIONING, ultimate
Strictly observe the instructions in chapter INSTALLATION.

CAUTION!

The refrigerant electrical components, located at the rear of the appliance, can reach high temperatures during ordinary operation. Carry out the installation according to this manual. An insufficient ventilation of the appliance will impair its operation and will damage the appliance. Do not cover or block the ventilation slats at any time
o not touch the extremely cooled surfaces with wet or damp hands, because your skin may stick on these surfaces.

NOTICE

When you move the appliance, hold it at its base and lift it carefully. Keep the appliance in an upright position.
Do not tilt the appliance more than 450.
Leave the appliance in an upright position for 4-6 hours before you connect it to the mains.
Never use the door for moving the appliance as you will damage the hinges.
When you unpack the appliance, you should take note of the position of every part of the interior accessories in case you have to repack and transport it at a later point of time.
Do not operate the appliance unless all components are installed properly.
Do not stand or lean on the base, the drawers, the doors etc of the appliance.
Do not put hot liquids or hot foodstuff into the appliance.
The air vents of the appliance or its built-in structure (if the appliance is suitable for being built-in) must be completely open, unblocked and free of any kind of dirt.

Product Usage Instructions

Installation

Choose a suitable location for the fridge as per the below guidelines:

The fridge should be placed on a flat and stable surface.
Ensure that the fridge is not exposed to direct sunlight or heat sources.
There should be enough space around the fridge for ventilation.
The fridge should be installed away from other heat sources such as an oven or radiator.

Site

Unpack the appliance carefully. Dispose of the packaging as described in chapter waste management.
The accessories of your appliance can be protected from damage due to transportation (adhesive tapes etc.). Remove such tapes very carefully. Remove remains of such tapes with a damp cloth using lukewarm water and a mild detergent (see also chapter CLEANING AND MAINTENANCE). Never remove any components of the back of the appliance!
Install the appliance in a suitable position with an adequate distance from sources of heat and cold.
Check that the appliance and the power cord are not damaged.
Install the appliance in a dry and well-ventilated place.
Protect the appliance from direct sunlight.
The doors must open completely and without hindrance.
Install the appliance on a level, dry and solid floor. Check the correct installation with a bubble level.
Connect the appliance to the mains properly.
The nameplate is inside the appliance or at the back.

Ventilation Change of the hinge position

Hinge cover
M5*12 screw
Top hinge
Door
Hinge support foot
Screw cover

WARNING! Unplug the appliance before changing the hinge position. RISK OF ELECTRIC SHOCK!
CAUTION! The change of the hinge position must be carried out by at least two persons; otherwise you may hurt yourself or damage the appliance. Do not tilt the appliance more than 450.
NOTICE! Adjust the door properly. The seal must close properly.

Remove the hinge cover.
Loosen the three screws of the top hinge. Remove the top hinge.
Remove the door.
Remove the bottom hinge.
Remove the screw cover.
Install the bottom hinge on the opposite side.
Install the door and install the top hinge.
Install the screw cover on the opposite side.
Install the hinge cover.

Cleaning and Maintenance

The fridge should be cleaned regularly to ensure its proper functioning. Follow the below guidelines for cleaning and maintenance:

Unplug the fridge before cleaning it.
Clean the interior and exterior of the fridge with a soft cloth and mild detergent.
Do not use abrasive cleaners or solvents.
The LED light inside the fridge does not require replacement as it has a long lifespan.

WARNING!

Disconnect the appliance from the mains before you clean or maintain it.
Always keep the appliance clean so that unpleasant odours do not occur.
Take off all rings and bracelets before cleaning or maintaining the appliance; otherwise you will damage the surface of the appliance.

Detergent

Do not use any harsh, abrasive or aggressive detergents.
Do not use any solvents.
Do not use any abrasive detergents! Do not use any organic detergents! 4Do not use essential oils!
These instructions are valid for all surfaces of your appliance.

External cleaning

Use a moist cloth and a mild, non-acidic detergent. Use a suitable detergent for stubborn stains.
Detergents such as vinegar, citric acid etc.
Use clear water to rinse.
Dry the cleaned surfaces with a cloth.

Internal cleaning

Clean the shelves and the inside with warm water and a mild detergent.
Use clear water to rinse.
Dry the cleaned surfaces with a cloth.
Check the water drain and clean it if needed.

Door seals

Clean with warm water and a mild, non- acidic detergent.

Replacing of the illuminant
WARNING! The LED-illuminant must be replaced by a competent person only. If the LED-illuminant is damaged, please contact a qualified professional (not covered by the guarantee).
NOTICE! This product contains a LED light source of energy efficiency class G according to EU-Regulation 2019/2015.

Troubleshooting

If the fridge is not functioning properly, follow the below steps:

Ensure that the fridge is properly plugged in and the socket is receiving power.
Check that the thermostat is set to the correct temperature.
Check that there is enough space around the fridge for proper ventilation.
If the problem persists, contact a qualified technician for assistance.

MALFUNCTION

POSSIBLE CAUSE| MEASURE
The appliance does not work at all.

The plug of the appliance is not connected to the socket.
The plug has become loose.
The socket is not supplied with energy.
The fuse is switched off.
The voltage is too low.

|

Check the corresponding socket by connecting it with another appliance.
Check the fuse box.
Compare the data on the model plate with the data of your energy supplier.

Insufficient cooling efficiency.

Soiled/damaged door gasket.
Improper ventilation.
Ambient temperature is too high/low.

|

Clean door gasket/gasket has to be replaced.
Check that ventilation meets the requirements in chap. 3.2.
Refer to schedule in chap. 2.

The door makes a strange sound when opened.
The door seals are soiled.| Clean the seals.
Uncommon noise.

The appliance is not installed on a flat and level ground.. The appliance touches a wall or other object
Frozen food is stored improperly.
Items have dropped behind the appliance.

|

Install properly.
Store food properly.
Remove the items.

If the appliance shows a malfunction not noted on the schedule above or if you have checked all items on the above schedule but the problem still exists, please contact the shop you purchased the appliance at.

Disposal

Do not dispose of the fridge with normal household waste.
Contact your local waste disposal authority for proper disposal methods.

Climatic classes

Look at chap. TECHNICAL DATA for information about the climatic class of your appliance. Your appliance can be operated in rooms with relevant room temperatures as named below.
HotelMate MC35E Semi Conductor Fridge 1

Operation

Main components

Ventilation openings
Housing
Hinge cover
Power cable
LED-illuminant
Door
Door gasket
Shelf
Condensate drain pan

Temperature Control

The temperature of the fridge can be controlled using the thermostat. The thermostat is not adjustable and is set to maintain a temperature of +5°C. The temperature may vary depending on the ambient temperature and the amount of food stored in the fridge.

Let the appliance operate for 2 hours while empty, before using it.
The factory setting of the refrigeration temperature is 8 0C, based on an ambient temperature of 25 0C.
Unplug the appliance when you do not operate it for more than 30 days.
You must unplug the appliance to disconnect it from the mains.
The cooling temperature cannot be set to a specific value. However, approximate modifications of the max. possible cooling temperature can be carried out, but the max. cooling temperature remains dependent on the ambient temperature.
The setting unit is on the back of the appliance.
The setting unit is on the back of the appliance.

Operational parameters

The appliance can only reach the relevant temperatures when:

the a ambient temperature meets the climatic class.
the doors close properly.
you do not open the doors too often or too long.
the door seals are in proper condition.
the appliance is properly positioned.
you have not overfilled the appliance.
you do not store warm or hot food in the appliance.

Helpful hints/energy saving

Do not overfill your appliance.
Try to open the door as little as possible, especially when the weather is warm and humid. If you open the door, close it as fast as possible.
Permanently check , that the appliance is well-ventilated. The appliance has to be well-ventilated from all sides.

Decommissioning

If the appliance is not used for a longer period of time:

Draw the plug out of the socket.
Remove all food stored in the appliance.
Dry the inside of the appliance with a cloth and leave the door open for a few days.

Ultimate decommissioning

Draw the plug out of the socket.
Cut off the power cord at the appliance.
Completely remove every door of the appliance.
Leave the shelves in their position so that children are not able to get into the appliance.
Follow the advice for the disposal of the appliance in chapter WASTE MANAGEMENT.

Waste management

Dispose of the appliance relevant to the current legislation in view of explosive gases. The cooling systems and insulation of refrigerators and freezers contain refrigerants and gases which have to be deposed of properly. Do not damage the cooling fins and tubes. If refrigerants escape there is FIRE HAZARD!
While unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept away from children. CHOKING HAZARD!
Old and unused appliances must be send for disposal to the responsible recycling centre. Never expose to open flames.
Before you dispose of an old appliance, render it inoperative. Unplug the appliance and cut off the entire power cord. Dispose of the power cord and the plug immediately. Remove the door completely so children are not able to get into the appliance as this endangers their lives!
Dispose of any paper and cardboard into the corresponding containers.
Dispose of any plastics into the corresponding containers.
If suitable containers are not available at your residential area, dispose of these materials at a suitable municipal collection point for waste-recycling.
Receive more detailed information from your retailer or your municipal facilities.

Refrigerant

The refrigerant circuit of the appliance contains the refrigerant R600a, a natural gas of high environmental compatibility.
WARNING! Do not damage any components of the refrigerant circuit while transporting the appliance. FIRE HAZARD!

Materials marked with this symbol are recyclable.
Please contact your local authorities to receive further information.
The refrigerant R600a is flammable!

Guarantee conditions

for large electric appliances; PKM GmbH & Co. KG, Neuer Wall 2, 47441 Moers.
This appliance includes a 24-month guarantee for the consumer given by the manufacturer, dated from the day of purchase, referring to its flawless material-components and its faultless fabrication. The consumer is accredited with both the dues of the guarantee given by the manufacturer and the vendor’s guarantees. These are not restricted to the manufacturer’s guarantee.
Any guarantee claim has to be made immediately after the detection and within 24 months after the delivery to the first ultimate vendee. The guarantee claim has to be verified by the vendee by submitting a proof of purchase including the date of purchase and/or the date of delivery. The guarantee does not establish any entitlement to withdraw from the purchase contract or for a price reduction. Replaced components or exchanged appliances demise to us as our property.
The guarantee claim does not cover:

fragile components as plastic, glass or bulbs;
minor modifications of the PKM-products concerning their authorized condition if they do not influence the utility value of the product;
damage caused by handling errors or false operation;
damage caused by aggressive environmental conditions, chemicals, detergents;
damage caused by non-professional installation and haulage;
damage caused by non common household use;
damages which have been caused outside the appliance by a PKM-product unless a liability is forced by legal regulations.

The validity of the guarantee will be terminated if:

the prescriptions of the installation and operation of the appliance are not observed.
the appliance is repaired by a non-professional.
the appliance is damaged by the vendor, the installer or a third party.
the installation or the start-up is performed inappropriately.
the maintenance is inadequately or incorrectly performed.
the appliance is not used for its intended purpose.
the appliance is damaged by force majeur or natural disasters, including, but with not being limited to fires or explosions.

The guarantee claims neither extend the guarantee period nor initiate a new guarantee period. The geographical scope of the guarantee is limited with respect to appliances, which are purchased and used in Germany, Austria, Belgium, Luxembourg and the Netherlands.