Wan Zhao Sheng Xue Technology EKSAE910 Gaming Headset User Manual

Wan Zhao Sheng Xue Technology EKSAE910 Gaming Headset User Manual

Specification

A： short press microphone mute (need prompt sound)
B： power switch key-long press control switch machine, short press switch ENC 7.1 function C： volume adjustment knob D、TYPC- mouth telescopic microphone after boot ear shell light long light. Introduction:

To connect the wireless USB adapter to any USB port on the PC that can work properly, or toconnect the USB extension line without installing any driver,

Notes:
USB adapter, restart headset, and then automatically connect, this product is a one-to-one pair of a single product, if not paired, please boot state press the key to open the code button 3-5 seconds until the headset blue light is always on, The emitter blue light is always on, that is, the code is successful.

By using the USB extension line, the transmitter can be placed in the best receiving position, thus expanding the receiving range of the wireless headset, which is designed to operate within the maximum distance of 40 feet (12 meters) of the wireless transmitter. But other wireless devices close to or under environmental conditions may affect performance.

Blue light flashes slowly = battery power is low

(horn beep)

| Blue lights on = code connection successful
A red light is on = is charging|
A red light = full|
 |
 |
 |

Important Tips:

5.8 G Wireless headset Wireless headset must be charged before first use Connect the USB charging line to any USB port on the PC that can be used normally. :: Connect the USB charging line to G 2.4 wireless headset. 5.8 G Wireless headset There is no “memory effect” on the wireless headset, so there is no need required before recharging.

Charging Instruction

Charge when power is off

When 5.8 G Wireless headset the headset is closed and charged by connecting the USB line

Charge when power on “play and charge mode”

When 5.8 G Wireless headset headset is turned on and charged by connecting the USBN line.

For best wireless performance:

• Place wireless adapters in accessible open areas.
• Wireless adapters require active USB ports (100 mA)

For maximum battery life:

• Ensure that batteries are charged before initial use
• Do not allow the battery to remain fully discharged for long periods of time so that the batteryremains partially charged to maximize battery life
• unplug the USB charging line immediately after the headset is charged
• Place the headset at room temperature (20-30℃ or 68-86℃)

Important Tips:

Listening to things in high volume for a long time may damage your hearing. Take a break every once in a while And at the beginning, the volume should be as low as possible, and then higher. Wear the headset on the head and adjust the headband to make it comfortable.

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
  connected.

• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>