LECTRON 15ATSLBLKUS 15 Amp Portable EV Charger Compatible User Manual
- June 17, 2024
- LECTRON
Table of Contents
LECTRON 15ATSLBLKUS 15 Amp Portable EV Charger Compatible
Specifications:
- Charger Type: Portable EV Charger
- Amperage: 15 Amp
- Compatibility: Tesla vehicles
- Plug Type: Tesla Plug
- Input Voltage: NEMA 5-15 (120 V)
- Cable Length: 16 ft
Product Usage Instructions
Safety Precautions:
Always follow the safety precautions provided in the user manual. Ensure
the charger is used in a dry environment and is not exposed to water or
extreme temperatures.
Installation:
Install the bracket with the screw then attach the charger module to the
mounting bracket until it clicks.
LED Indicators:
The LED indicators provide important information about the charging
process:
- Power status On/Off
- Charger-connection status
- Charging status
- Error indicator
Charging Your Vehicle:
- Ensure your car is parked and the engine is turned OFF.
- Insert the charger into an appropriate wall outlet.
- Plug the charging handle into your vehicle’s charging outlet.
- Charging begins automatically. Verify the Charging Indicator on the charger is blinking continuously.
- Monitor the vehicle panel to check the charging status. When fully charged, the Charging Indicator will stay solid.
- Once fully charged, pull out the charging handle from the vehicle.
FAQ:
-
Q: What should I do if the Charging Indicator does not light up?
A: Check the power source and connections to ensure proper contact. If issues persist, refer to the troubleshooting section in the user manual. -
Q: Can I use this charger with non-Tesla electric vehicles?
A: No, this charger is specifically designed for Tesla vehicles and may not be compatible with other electric vehicles.
Safety Precautions
- It is recommended that electrical outlets for your charger should be installed by a licensed and qualified electrician. To avoid serious injury or death, installation must comply with the provisions of the National Electric Code (NEC) and all local codes. If there are conflicts between local codes and the NEC, local codes shall take precedence.
- This product must be grounded. In case of a malfunction or breakdown, grounding can help reduce the risk of electric shock. This product includes a cord that is equipped with a grounding conductor and a grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
- SHOCK HAZARD – Make sure the plug is fully inserted into the wall outlet to avoid any exposed metal surfaces.
- Do not leave children unattended or unsupervised around chargers or other power outlets or devices
- DO NOT DROP THE CHARGER OR HANDLE.
- If the output plug is separated from the charger module or the charging handle, DO NOT ATTEMPT TO REPAIR THE CABLE YOURSELF. For assistance, contact Customer Service at: contact@ev-lectron.com
- When using your charger, basic precautions should always be followed, including:
- Read warnings on the charger-cord label before operating the charger for the first time.
- Read all instructions in this guide before using the charger.
- Never use the charger with non-approved power adapters or other power components.
In the Box
How to Install
- Install the bracket with the screw then attach the charger module to the mounting bracket until it clicks
LED Indicators
LED Status
Charging Your Vehicle
NOTE : Ensure your car is parked and the engine is turned OFF.
- Insert the charger into an appropriate wall outlet.
- The Power and Connected lights will light up and stay solid, which means the charger is receiving AC power and is ready for use.
- Plug the charging handle into your vehicle’s charging outlet
- Charging begins automatically. Power will be delivered in accordance with the demand of your vehicle. While charging, the Charging Indicator will continuously blink. Always verify your vehicle charging status by checking the vehicle panel
- When your vehicle is fully charged, the Charging Indicator light will stay solid. Your vehicle has a “dashboard gauge”, which also shows if your vehicle is fully charged. Refer to your vehicle user manual to find the location of the gauge on the dashboard.
- When the vehicle is fully charged, pull the charging handle out of the vehicle.
NOTE : The charger requires a 120 V AC split phase. It draws a maximum of 15 Amps of continuous current.
Troubleshooting
Please refer to this troubleshooting guide to fix common charging errors or while using the portable charger
| Problem | Possible Cause | Solution |
|---|
Charging Indicator does not illuminate
|
No power to the charger.
|
1. Check the circuit breaker and other circuit loads.
2. Try another wall outlet.
3. Ensure that the charger module (and adapter if operating in 120 V AC mode) is fully inserted into the wall outlet.
Contact Lectron Customer Support at contact@ev-lectron.com for assistance.
Vehicle will not charge
|
Charging handle is not properly inserted into the vehicle.
| 1. Inspect the charging handle.
2. Remove the charging handle from the vehicle, then reinsert it into the vehicle outlet until it clicks.
Vehicle cannot accept any charge.
| Verify that the vehicle charge timer is set to permit charging. Refer to the vehicle user manual for charge timer instructions.
Communication error between the charger and vehicle.
|
Contact Lectron Customer Support at contact@ev-lectron.com for assistance.
Above the temperature limit.
Cases:
1. Temperature is too high. The charger will restart charging when it cools down.
2. House/socket wiring may be faulty.
|
1. Inspect the charger module for overheating:
a. Carefully unplug the charger module from the wall outlet and allow it to cool.
b. If the problem continues, contact Lectron Customer Support at contact@ev- lectron.com for assistance.
2. Disconnect the charger from the wall outlet.
3. Have a qualified electrician inspect the wall outlet and adapter.
Error Indicator is blinking rapidly
|
Utility fault.
|
1. Disconnect the charger module from the wall outlet and reconnect it.
2. If the problem continues, have a qualified electrician inspect the ground circuit of the wall outlet.
Specifications
Rated current:
| ****
15 Amp
---|---
Input/output:
| ****
120 V AC
Frequency:
| ****
50/60 Hz
Cable length:
| ****
16 ft (5 m)
Plug:| ****
NEMA 5-15
EV charging handle:| ****
Tesla (Compatible with NACS)
Dimensions:| ****
8.1 x 3.2 x 1.6 in (20.8 x 8.2 x 4.23 cm)
Weight:| ****
5.3 lb (2.4 kg)
Operating temperature:| ****
-22 °F to +122 °F (-30 °C to +50 °C)
Material:| ****
PC+ABS
Control-box water resistance:| ****
IP65
Charging handle water resistance:| ****
Type 3R
Reference standard:| ****
UL2594, UL2251, UL2231
Get More Support
www.ev-lectron.com
Made in China
Scan the QR code below or email us at contact@ev-lectron.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>