SEALEY HVF20PO 20 Inch Industrial High Velocity Oscillating Pedestal Fan Instructions
- June 4, 2024
- SEALEY
Table of Contents
20” INDUSTRIAL HIGH VELOCITY
OSCILLATING PEDESTAL FAN
MODEL NO: HVF20PO
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT IS CORRECTLY
AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe
before use. Inspect power supply leads, plugs, and all electrical connections
for wear and damage. Sealey recommends that an RCD (Residual Current Device)
is used with all electrical products. You may obtain an RCD by contacting your
local Sealey dealer.
If the product is used in the course of business duties, it must be maintained
in a safe condition and routinely PAT (Portable Appliance Test) tested.
For electrical safety information, it is important that the following
information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe
before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and
check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the
power supply to be used and that the plug is fitted with the correct fuse –
see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty
item is repaired or is replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply
and remove it from use.
Ensure that repairs are carried out by a qualified electrician. Replace a
damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a
qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that
the restraint is tight. 3 Amp Sealey recommends that repairs are carried out
by a qualified electrician.
1.1.5. If an extension reel is used it should be unwound fully before
connection. A reel with an RCD fitted is preferred since any appliance plugged
into it will be protected. The cable core section is important and should be
at least 1.5mm², but to be absolutely sure that the capacity of the reel is
suitable for this product and for others that may be used in the other output
sockets, we recommend the use of 2.5mm² section cable.
GENERAL SAFETY
9 Disconnect the fan from the mains’ power when not in use, and before
servicing or performing any maintenance. 9 Use the fan in dry areas only.
DO NOT use in wet or areas with high condensation such as showers, pools, etc.
WARNING! If the fan falls into water or other liquid, switch off and
disconnect from the mains power supply immediately.
DO NOT touch the fan until the mains power supply has been disconnected. 9
Always disconnect the fan from the power supply when moving it from one
location to another and ensure the fan stands on a level surface.
The fan airflow is powerful. Before using ensure there are no materials or
items that may be blown about by the stream of air. 9 Keep the fan clean and
maintained in good condition. For electrical components or motor service
contact an authorized service agent.
Use recommended parts only (unapproved parts may be dangerous, and will
invalidate your warranty).
DO NOT operate the fan where there are harmful, explosive, or flammable gases,
fumes, or hazardous substances.
DO NOT stand the fan on the electrical power cable.
DO NOT insert any objects through the fan guard.
DO NOT cover the fan when in use.
DO NOT immerse the fan in water or any other liquid.
DO NOT allow children to operate the fan.
DO NOT stand the fan where it may be knocked over or off a surface, or where
the lead may cause a person to trip.
DO NOT use the fan outdoors.
DO NOT modify speed control or attempt to fit any additional external speed
control device to the fan. 9 When not in use cover the fan to protect it from
dust, and store it in a safe, dry, childproof location.
NOTE: This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
INTRODUCTION
The high-velocity fan is suitable for the movement of huge volumes of air. Features three-speed settings for choice of airflow, height adjustable stand, tilting blade cradle, and oscillation. Fully guarded blades with a large diameter base for safety and added stability. Suitable for industrial, commercial, Agricultural, workshop, and showroom applications.
SPECIFICATION
Model no: ………………………………………………………HVF20PO
Fan diameter: ……………………………………………..550mm (20”)
Speeds: ……………………………………………………………………..3
Speed range: ……………………………………1050/1150/1350rpm
Maximum airflow: …………………………….110m³/min (3900cfm)
Height: …………………………………………………… 1080-1410mm
Power: ………………………………………………………….. 110-115W
Supply: …………………………………………………………………230V
Current: …………………………………………………………………0.5A
Maximum Flow Rate (F): ……………………………. 160.35m3/min
Fan Power Input (P): …………………………………………..105.5W
Service Value (SV): ………………………………….1.52(m3/min)/W
Standby Power Consumption (PSB): …………………………0.0W
Seasonal Electricity Consumption (Q): ……………. 33.76kWh/a
Fan Sound Power Level (Lwa): ………………………. 78.26dB(A)
Maximum Air Velocity (c): …………………………………… 3.31m/s
ASSEMBLY
4.1. Bolt the bottom tube to the base as in fig.1.1.
4.2. Place the fan head assembly on the upper tube (fig.1.2)
4.3. Secure the fan head assembly by means of the two bolts as shown in
fig.1.3.
4.4. The height is adjustable by loosening the collar on the tube, sliding to
the required height and re-tightening.
4.5. The angle of the head is adjusted by loosening the head clamp and moving
the head and retightening the clamp.
OPERATION
IMPORTANT: Ensure that all safety instructions from section 1 have been
read and understood before using the fan.
5.1. Set the fan on a level, dry surface.
5.2. Plug the power cord into the main supply.
5.3. The fan features 3 speeds – selectable using the switch located at the
back of the fan (fig.2.1.) The fan speed increases as the switch is turned in
a clockwise direction.
5.4. To start the fan oscillating, press the control button (fig.2.2.) down,
and lift to stop the oscillation.
5.5. When not in use, disconnect from the power supply and store in a safe,
dry, childproof location.
MAINTENANCE
IMPORTANT: Turn the control switch to OFF and disconnect the fan from the
power supply before cleaning.
6.1. Use only a soft, damp cloth to clean the fan.
DO NOT submerse the fan in water and NEVER allow water to drip into the motor
housing.
DO NOT use solvents or other chemicals to clean the fan.
6.2. To clean the fan blades, loosen the 7 clips around the guards and then
lift off the front guard from the top hook.
6.3. Reassemble by hooking the front guard into place at the top of the rear
guard and then pushing the 7 clips back into place so that they engage both
the front and rear guards.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories, and packaging should be sorted, taken to a recycling center, and
disposed of in a manner that is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
**** sales@sealey.co.uk
**** www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
HVF20PO Issue:3 (3) 29/10/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>