XTRACTION ULTRAG 2004 Chevrolet Corve Deluxe Pit Kit Instruction Manual

: June 17, 2024
: XTRACTION ULTRAG

Table of Contents

XTRACTION ULTRAG 2004 Chevrolet Corve Deluxe Pit Kit
Product Usage Instructions
ASSEMBLY INSTRUCTIONS
PARTS LIST
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

XTRACTION ULTRAG 2004 Chevrolet Corve Deluxe Pit Kit

XTRACTION-ULTRAG-2004-Chevrolet-Corve-Deluxe-Pit-Kit-
product

Specifications:

Chassis: 1 piece
Gear Plate: 1 piece
Pinion Gear: 1 piece
Idler Gear: 1 piece
Cluster Gear: 1 piece
Retainer Clip: 1 piece
Armature: 1 piece
Rear Magnet (Red): 1 piece
Front Magnet: 1 piece
Commutator Brushes: 2 pieces
Commutator Springs: 2 pieces
Rear Axle: 1 piece
Rear Wheel: 2 pieces
Rear Tire: 2 pieces
Crown Gear: 1 piece
Front Wheel: 2 pieces
Front Axle: 1 piece
Front Tire: 2 pieces
Connector Plate (Right): 1 piece
Connector Plate (Left): 1 piece
Rivet: 2 pieces
Pick-up Spring: 2 pieces
Pick-up Shoe: 2 pieces
Guide Pin: 1 piece
Ultra-GTM Magnet: 1 piece

Product Usage Instructions

Assembly Instructions:

Insert the two commutator springs (12) into the center holes of the chassis (1). Place a commutator brush (11) on top of each spring.
Slide the front magnet (10) into the front recess of the chassis (1), followed by the rear magnet (9) into the rear recess.
Place the idler gear (4) over the pin on the gear plate (2) aligning the teeth with the armature pinion gear (3) and cluster gear (5).
Lower the gear plate (2) onto the chassis (1), aligning the armature (8) between the magnets.
Secure the idler gear by placing and snapping the retainer clip (7) into place.
Install pick-up springs and shoes on both sides of the chassis.
Attach rear tires (15) to rear wheels (14) and front tires (19) to front wheels (17).
Insert the guide pin (25) into the front of the chassis.
Insert the chassis into the body to complete assembly.

Racing Instructions:

Your X-Traction slot car is now ready to race. Test it on the track. If there are any issues, review each assembly step and ensure the correct placement of magnets. Visit autoworldslotcars.com for more information.

FAQ:

Q: What should I do if my car does not run properly?
A: Re-read each assembly step to confirm correct completion. Check magnet orientation in the chassis. Visit autoworldslotcars.com for troubleshooting tips.
Q: How can I improve performance?
A: Ensure tires are squared on rims. Regular maintenance and cleaning of components can also enhance performance.

ASSEMBLY INSTRUCTIONS

NOTE : Some parts shown in the diagram are pre-assembled

Insert the two commutator springs (12) into the center holes of the chassis (1). These are the shorter, softer springs included in the Pit Kit. Place a commutator brush (11), flat side up, on top of each spring.
Slide the front magnet (10), with a white painted edge facing down, into the front recess of the chassis (1). Now slide the rear magnet (9), with its red-painted edge facing down, into the rear recess of the chassis.
Place the idler gear (4) over the pin on the gear plate (2), aligning the teeth with the armature pinion gear (3) and cluster gear (5).
Lower the gear plate (2) onto the chassis (1) by first sliding the front tabs on the gear plate into the notches in the chassis and centering the armature (8) between the magnets.
Slip one side of the retainer clip (7) into the notch on one side of the chassis (1). Spread the clip slightly and snap it into the other side of the chassis, to hold the idler gear in place.
Flip the chassis over. Place a pick-up spring (23) in the circular recessed area of the left connector plate (21).
Hook the rear edge of a pick-up shoe (24) under the lip on the forward edge of the left metal connector plate (21), taking care not to move the pick-up spring. Bring the front of the pick-up shoe down, compressing the pick-up spring, and lightly snap the hole in the front face of the shoe over the locating tab on the front edge of the chassis. Repeat this procedure for the other side using the second pick-up spring and shoe.
Slide a rear tire (15) onto each rear wheel (14). Keeping the tires squared on the rims will improve performance!
Slide a front tire (19) onto each front wheel (17).
Snap the guide pin (25) into the front of the chassis (1).
Holding the body upside down, lower the chassis into the body on an angle, inserting the tab on one side of the chassis into the notch inside the body. Lightly spread the body open enough to snap the other side of the chassis into the body.

Your X-Traction slot car should now be ready to race!
Test your car on the track. If it does not run properly, re-read each assembly step to confirm you have completed it correctly. If the car runs backward, ensure the magnets are in the correct orientation in the chassis. For more information, visit autoworldslotcars.com.