Inwa MZ-320B Garden Light Wireless Speaker User Manual

User Manual

Safety Notice

1. Read all instructions and save for future reference.
2. Operate the product in accordance with all instructions.
3. Please heed all warnings in this product and in the User Manual.
4. Clean only with a dry cloth. Be sure to unplug the power adapter from any power source before cleaning.
5. Do not use third-party accessories or non-recommended accessories on this product.
6. Do not place the product on unstable surfaces, such as carts, shelves, tripods, etc., which may drop the product and cause serious personal injury and serious damage to the product.
7. Do not block or cover the vents. Openings in the product compartment ensure efficient cooling and prevent overheating. Do not place the product on beds, sofas and rugs, and do not install it on shelves or bookshelves unless proper ventilation is provided.
8. Do not charge for a long time when not in use.
9. Do not place this product near heat sources. Avoid radiators, stoves, and other appliances that generate heat, and avoid prolonged exposure to sunlight and heat.
10. Please consult professionals for all services. If the product is damaged or malfunctions during use, please contact qualified service personnel. Do not repair it yourself.
11. For wireless use, unplug the power adapter completely.

Quick Start Guide

1. Packing list
2. Product parameters

Input voltage: DC5V 2.5A
Output power: 15W2
Frequency response: 20Hz-20KHz
Bluetooth distance: 10~20m
Bluetooth version: 5.3
Auxiliary input: 3.5mm
Distortion: <1%
Signal-to-noise ratio: >85dB
Working time: 60% volume can play continuously for 10hr. Note: Speaker will auto shut down after two hours of Bluetooth disconnection.
Battery capacity: 26002mAh
Standby time: >300hr
Waterproof grade: IPX5
Charging time: 3-4hr
Serial transmission distance: <40m
Operating temperature range: 0°- 40°
Operating humidity range: 40 – 50%RH
Storage temperature range: -25°C – 70°
Product net weight: 2230g (With battery)
Product size: W182xD182xH283mm

Operation Instructions

1. Function panel and port desci on1. Switch and play pause key
   2. Light brightness key
   3. Lighting mode key
   4. Ambient light key
   5. Pairing key
   6. Long press volume down/
   7. Long press volume up/ (networking/Bluetooth) short press previous song short press next song
   8. Charging indicator
   9. Audio input indicator
   10. Main speaker indicator
   11. Aux. speaker indicator

2. Speaker charging
   Notice: The speaker must be fully charged before use.
   1. Open the rubber cover, then plug the power adapter (5V 2.5A) into the charging port.
   2. Plug the power adapter into a power outlet.
   3. When charging, the red indicator light is on; when the red indicator light is off, it means fully charged.

3. Bluetooth pairing
   (The speaker must be powered on, press and hold the power button for 2 seconds to switch on and off)
   A. Establish a new connection
   1. The Bluetooth (TX) white indicator light will flash quickly after the speaker is turned on.
   (If the bluetooth (TX) white light is not flashing or only the red indicator light flashing, double- click or long press the bluetooth pairing key ” ” until white indicator light is flashing)
   2. Enable bluetooth in the device settings and select the bluetooth name “MZ-320”.
   3. After successful pairing, the TX white light will stay on and you will hear a beeping sound.
   4. Short press the power key “ ” to play and pause music.
   B. Disconnect and pair with new device
   1. After the device is paired successfully, double-click the Bluetooth pairing key ” “, the TX white indicator flashes quickly, and a beep sounds, and the connected Bluetooth device will be disconnected.
   2. Repeat steps 1-3 in the previous section (establish a new connection). Notice: When pairing, the Bluetooth device and the speaker should be close together (10m/33.3ft).

4. Sync speakers
   Sync pairing:
   1 Turn on one speaker (main speaker), and connect it to the Bluetooth device.
   2 Then turn on the next speaker (Aux. speaker) and it will automatically connect to the main speaker.
   Tip: If Aux. speaker didn’t connect with main speaker. Long press the network pairing key “ ” on the Aux. speaker for 2 seconds until the orange indicator light (RX) starts flashing and it will automatically connects to the main speaker. Notice: When the speakers are in sync, the main speaker’s TX white indicator light and the Aux. speaker’s RX orange indicator light will stay on. Notice: When synchronizing the speaker, you need to connect the Main speaker (TX) with the Bluetooth device, and then the Aux. speaker (RX) can automatically connect to the Main speaker (TX) for synchronous networking.

5. AUX input
   The speaker comes with a 3.5mm audio cable, you can use the 3.5mm audio cable to listen to music. In this case, Bluetooth will be disabled, and the speaker automatically switches to AUX input mode.
   1. Plug the 3.5mm audio cable into the audio jack of the device, (make sure the audio jack is not blocked by any protective sleeves or accessories).
   2. After plugging the audio cable into the speaker, you will hear a beep sound and the red light will be on.

6. Light display
   A. Lighting switch
   1. Press the lighting key (The default brightness when the light is on is: 100%)
   2. Press the lighting key each time, and switch the lighting cyclically: white light, warm white, turn off the light. B. Light brightness control
   1. Press the lighting key “ “. (The default brightness when the light is on is: 100%)
   2. Press the light brightness key “ ” each time, and adjust the brightness cyclically: 100%, 75%, 50%, 25%. C. Ambient light selection
   The ambient light must be turned on to change the color of the ambient light, press the ambient light key “ “. the color of the ambient light is displayed in the following order:
   1. Rhythm flashing light (Beat-driven flashing lights)
   2. Dark blue (no flashing)
   3. Green (no flashing)
   4. Purple (no flashing)
   5. Red (no flashing)
   6. Pink (no flashing)
   7. Flame light
   8. Colorful flowing light Notice:
   The default is light mode 1 rhythm flashing light when power on.
   (When there is no music, the brightness is 25%, and the 5 colors are switched at an interval of 5 seconds. When there is music, the brightness flashes at 25-100%)

7. Support Information
   Need further help, you can contact us by
   A. Service E-mail: inwa_support@innosystemtech.com
   B. Or contact us on Amazon
   1. Go to Your Orders.
   2. Find your order in the list.
   3. Select Problem with order.
   4. Choose your topic from list displayed. Select Contact seller.

GOAL REACH CONSULTING LTD
OFFICE 1029 3 HARDMAN STREET 10TH
FLOOR, SPINNINGFIELDS MANCHESTER,
UK M3 3HF
OST UK 20230424000006 goalservice@hotmail.com
We simply act as UK representative for cross-border sellers, and are not manufacturers/importers/distributors for the product, nor involved in the manufacture/import/sale of the product.
Therefore, we are not responsible for any after-sales services related to the product. In case of any product quality or infringement issues, the manufacturer/importer/seller shall be solely held responsible.
SUCCESS COURIER SL
CALLE RIO TORMES NUM.1, PLANTA 1,
DERECHA , OFICINA 3, Fuenlabrada,
Madrid, 28947 Spain
OST_EU_20230424000022 successservice2@hotmail.com
We simply act as EU representative for cross-border sellers, and are not manufacturers/importers/distributors for the product, nor involved in the manufacture/import/sale of the product.
Therefore, we are not responsible for any after-sales services related to the product. In case of any product quality or infringement issues, the manufacturer/importer/seller shall be solely held responsible.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>